Axle Load Spectra Characterization by Mixed Distribution Modeling
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Transportation Engineering
Volume 131, Issue 2
Abstract
Traffic comprises a primary input to any pavement design methodology. As pavement design evolves from traditional empirically based methods toward mechanistic-empirical (M-E), there will be a greater emphasis placed on accurate characterization of the distributions of axle loads, because they are entered directly into pavement response models. Known as load spectra, these distributions of axle weight are often complex and not well represented by individual theoretical statistical distributions. This research proposes a mixed distribution model of two or more theoretical distributions to accurately characterize axle load spectra. This paper details the model development and demonstrates its predictive capability using weigh-in-motion data from 13 sites in Alabama. The data show the predictive capability of the mixed distribution model through high values, exceeding 0.96 in all cases. The typical axle load distribution in Alabama is comprised of a combination of lognormal and normal distributions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers wish to acknowledge the Alabama Department of Transportation and the Auburn University Highway Research Center for their cooperation and support of this research.
References
American Association of State Highway and Transportation Officials (AASHTO). (2003). AASHTO guide for design of pavement structures, Washington, D.C.
Chia-Pei, J. C., and Ching, C. P. (1995). “Truck load distribution and its impact on vehicle weight regulations in Taiwan.” Transportation Research Record. 1501, Transportation Research Board, Washington, D.C., 87–94.
Devore, J. L. (1995). Probability and statistics for engineering and the sciences, 4th Ed., Duxbury Press.
Jones, D. (2003). “Vehicle Travel Information System (VTRIS).” Federal Highway Administration, ⟨http://www.fhwa.dot.gov/ohim/ohimvtis.htm⟩.
Huang, W.-H., Sung, Y.-L., and Lin, J.-D. (2002). “Development of axle load distribution for heavy vehicles.” Pre-Prints, 81st Annual Meeting, Transportation Research Board, Washington, D.C.
Kim, J. R., Titus-Glover, L., Darter, M. I., and Kumapley, R. K. (1998). “Axle load distribution characterization for mechanistic pavement design.” Transportation Research Record. 1629, Transportation Research Board, Washington, D.C., 13–17.
Liu, W. D., Cornell, C. A., and Imbsen, R. A. (1988). “Analysis of bridge truck loads.” Probabilistic methods in civil engineering, P. D. Spanos, ed., ASCE, New York, 221–224.
Mohammadi, J., and Shah, N. (1992). “Statistical evaluation of truck overloads.” J. Transp. Eng., 118(5), 651–665.
“NIST/SEMATECH e-handbook of statistical methods.” (2002). ⟨http://www.itl.nist.gov/div898/handbook/⟩ (Oct. 28, 2002).
Shah, N. (1989). “An investigation of overloads on highway bridges.” M.S. thesis, Illinois Institute of Technology, Chicago.
Timm, D. H., Newcomb, D. E., and Galambos, T. V. (2000). “Incorporation of reliability into mechanistic-empirical pavement design.” Transportation Research Record. 1730, Transportation Research Board, Washington, D.C., 73–80.
Tisdale, S. M. (2003). “Development of truck equivalency factors and axle load spectra for pavement design.” MS thesis, Auburn Univ., Auburn, Ala.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Jul 1, 2003
Accepted: Feb 24, 2004
Published online: Feb 1, 2005
Published in print: Feb 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.