Structural Behavior of Concrete Block Paving. I: Sand in Bed and Joints
This article has a reply.
VIEW THE REPLYPublication: Journal of Transportation Engineering
Volume 128, Issue 2
Abstract
The quality of the bedding sand, jointing sand, joint width, and thickness of bedding course in concrete block pavement influence the performance of the entire pavement. A review of the literature revealed a wide range of views regarding the behavior of bedding sand, jointing sand, and concrete blocks in a block pavement. This paper describes the results of a series of tests conducted to investigate the effects of changing parameters of bedding and jointing sand on pavement performance. The influence of block parameters has been presented separately as a companion paper. A laboratory-scale test was used to study these parameters based on static plate loading tests. Eight different grades of sand ranging from coarse to fine were used in the test program. The pavement responses are characterized in terms of deflection due to applied load for half of a legal single axle limit. The results indicate that coarse grade sand is preferable.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (1998). “Standard test methods for vulcanized rubber and thermoplastic rubbers and thermoplastic elastomers-tension.” D412-98a, West Conshohochen, Pa.
Bose, S. (1994). “Elastic modulus of granular bases in flexible pavements.” PhD thesis, Civil Engineering Dept., Indian Institute of Technology, Kharagpur, India.
British Standards Institute (BSI). (1973). “Specification for aggregates from natural sources of concrete.” British Standard 882, 1201: Part 2: 1973, London.
Bureau of Indian Standards (BIS). (1963). “Indian standard methods of test for aggregates for concrete.” (1963). IS: 2386-1963, New Delhi, India.
Bureau of Indian Standards (BIS). (1970). “Indian standard specifications for coarse and fine aggregates from natural sources for concrete (second revision).” IS 383-1970, New Delhi, India.
Bureau of Indian Standards (BIS). (1976). “Indian standard methods of test of burnt clay building bricks (second revision).” IS 3495-1976, New Delhi, India.
Bureau of Indian Standards (BIS). (1983). “Indian standard methods of test for soils (second revision).” (1983). IS 2720-1983, New Delhi, India.
Eisenmann, J., and Leykauf, G. (1988). “Design of concrete block pavement in FRG.” Proc., 3rd Int. Conf. on Concrete Block Paving, Pavitalia, Rome, 149–155.
Ghafoori, N., and Mathis, R.(1998). “Prediction of freezing and thawing durability of concrete paving blocks.” J. Mater. Civ. Eng., 10(1), 45–51.
Ghafoori, N., and Mathis, R.(1997). “Sulfate resistance of concrete pavers.” J. Mater. Civ. Eng., 9(1), 35–40.
Huurman, M. (1997). “Permanent deformation in concrete block pavements.” PhD thesis, Delft Univ. of Technology, Delft, The Netherlands.
Indian Road Congress (IRC). (1984). “Guidelines on design of flexible pavements.” IRC 37-1984, New Delhi, India.
Knapton, J., and Barber, S. D.(1979). “The behavior of a concrete block pavement.” Proc. Inst. Civ. Eng., London, 66(1), 277–292.
Knapton, J., and O’Grady, M. (1983). “Structural behavior of concrete block paving.” J. Concrete Soc., 17–18.
Lilley, A. A. (1980). “A review of concrete block paving in the UK over the last five years.” Proc., 1st Int. Conf. on Concrete Block Paving, Newcastle-upon-Tyne, U.K., 40–44.
Lilley, A. A., and Dowson, A. J. (1988). “Laying course sand for concrete block paving.” Proc., 3rd Int. Conf. on Concrete Block Paving, Pavitalia, Rome, 457–462.
Livneh, M., Ishai, I., and Nesichi, S. (1988). “Development of a pavement design methodology for concrete block pavements in Israel.” Proc., 3rd Int. Conf. on Concrete Block Paving, Pavitalia, Rome, 94–101.
Mavin, K. C. (1980). “Interlocking block paving in Australian residential streets.” Proc., 1st Int. Conf. on Concrete Block Paving, Newcastle-upon-Tyne, U.K., 150–154.
Ministry of Surface Transport (MOST). (1995). Specifications of road and bridge works (third revision), Indian Road Congress, New Delhi, India.
Panda, B. C., and Ghosh, A. K.(1999). “Structural modeling and design of interlocking concrete block pavement.” Indian Concr. J., 73(2), 123–127.
Panda, B. C., and Ghosh, A. K.(2001). “Source of jointing sand for concrete block pavement.” J. Mater. Civ. Eng., 13(3), 235–237.
Rada, G. R., Smith, D. R., Miller, J. S., and Witzak, M. W.(1990). “Structural design of concrete block pavements.” J. Transp. Eng. 116(5), 615–635.
Shackel, B. (1980). “The performance of interlocking block pavements under accelerated trafficking.” Proc., 1st Int. Conf. on Concrete Block Paving, Newcastle-upon-Tyne, U.K., 113–120.
Shackel, B., O’Keeffe, W., and O’Keeffe, L. (1993). “Concrete block paving tested as articulated slabs.” Proc., 5th Int. Conf. on Concrete Pavement Design and Rehabilitation, Purdue Univ., West Lafayette, Ind., 89–95.
Sharp, K. G., and Simons, M. J. (1980). “Interlocking concrete blocks: state-of-art review.” Proc., Australian Road Research Board, 10(2), 205–218.
Simmons, M. J. (1979). “Construction of interlocking concrete block pavements.” Australian Road Research Rep. ARR No. 90, 71–80.
Van der Vlist, A. A. (1980). “The development of concrete blocks in The Netherlands.” Proc., 1st Int. Conf. on Concrete Block Paving, Newcastle-upon-Tyne, U.K., 14–22.
Information & Authors
Information
Published In
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: May 4, 2000
Accepted: Mar 16, 2001
Published online: Mar 1, 2002
Published in print: Mar 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.