Tubular Links for Eccentrically Braced Frames. II: Experimental Verification
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 134, Issue 5
Abstract
This paper describes the results of an experimental study to verify proposed design requirements for eccentrically braced frame links with hollow rectangular (i.e., tubular) cross sections. Twelve primary link specimens and two supplementary links that have different end connections are tested. Three cross sections and four normalized link lengths are considered. Two of the cross sections have web and flange compactness ratios near the proposed limits while the third cross section has compactness ratios significantly less than the proposed limits. Shear, intermediate, and flexural, link lengths are tested, including some at the critical transition length from shear-to-intermediate link behavior. Results indicated that tubular links satisfying the proposed compactness and stiffener requirements can achieve the target plastic rotations for wide-flange links when subjected to the loading protocol specified in the 2005 AISC Seismic Provisions. The predominant failure mode is fracture of the link flange near the connection to the end plates used for testing. A method for calculating the ultimate link shear, proposed by others for wide-flange links, is also investigated and modified to agree with the results of the tubular link tests.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was conducted by the State University of New York at Buffalo and was supported by the Federal Highway Administration under Contract No. UNSPECIFIEDDTFH61-98-C-00094 and the Multidisciplinary Center for Earthquake Engineering Research. However, any opinions, findings, conclusions, and recommendations presented in this paper are those of the writers and do not necessarily reflect the views of the sponsors.
References
AISC. (2002). Seismic provisions for structural steel buildings, Chicago.
AISC. (2005). Seismic provisions for structural steel buildings, Chicago.
Berman, J. W., and Bruneau, M. (2005). “Approaches for the seismic retrofit of braced steel bridge piers and proof-of-concept testing of a laterally stable eccentrically braced frame.” Technical Rep. No. MCEER-05-0004, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, N.Y.
Berman, J. W., and Bruneau, M. (2006). “Further development of tubular eccentrically braced frame links for the seismic retrofit of braced steel truss bridge piers.” Technical Rep. No. MCEER-06-0006, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, N.Y.
Berman, J. W., and Bruneau, M. (2007). “Experimental and analytical investigation of tubular links for eccentrically braced frames.” Eng. Struct., 29(8), 1929–1938.
Berman, J. W., and Bruneau, M. (2008). “Tubular links for eccentrically braced frames. I: Finite element parametric study.” J. Struct. Eng., 134(5), 692–701.
Dafalias, Y. F., and Popov, E. P. (1976). “Plastic internal variables formalism of cyclic plasticity.” J. Appl. Mech., 43(4), 645–651.
Dusicka, P., Itani, A. M., and Buckle, I. G. (2002). “Cyclic behavior of shear links and tower shaft assembly of San Francisco-Oakland Bay Bridge Tower.” Technical Rep. No. CCEER 02-06, Center for Civil Engineering Earthquake Research, Univ. of Nevada, Reno, Reno, Nev.
Engelhardt, M. D., and Popov, E. P. (1992). “Experimental performance of long links in eccentrically braced frames.” J. Struct. Eng., 118(11), 3067–3088.
Hjelmstad, K. D., and Popov, E. P. (1984). “Characteristics of eccentrically braced frames.” J. Struct. Eng., 110(2), 340–353.
Itani, A. M. (1997). “Cyclic behavior of Richmond-San Rafael Tower Links.” Technical Rep. No. CCEER 97-4, Center for Civil Engineering Earthquake Research, Univ. of Nevada, Reno, Reno, Nev.
Kasai, K., and Popov, E. P. (1986). “General behavior of WF steel shear link beams.” J. Struct. Eng., 112(2), 362–382.
Malley, J. O., and Popov, E. P. (1984). “Shear links in eccentrically braced frames.” J. Struct. Eng., 110(9), 2275–2295.
Metris, Inc. (2005). K-Series cameras by Metris, Inc., ⟨www.metris.com⟩.
Okazaki, T., Arce, G., Ryu, H. C., and Engelhardt, M. D. (2005). “Experimental study of local buckling, overstrength, and fracture of links in eccentrically braced frames.” J. Struct. Eng., 131(10), 1526–1535.
Pollino, M., and Bruneau, M. (2004). “Seismic retrofit of bridge steel truss piers using a controlled rocking approach.” Technical Rep. No. MCEER-04-0011, Multidisciplinary Center for Earthquake Engineering Research, State Univ. of New York at Buffalo, Buffalo, N.Y.
Popov, E. P., and Bertero, V. V. (1980). “Seismic analysis of some steel building frames.” J. Engrg. Mech. Div., 106(1), 75–92.
Richards, P. (2004). “Cyclic stability and capacity design of steel eccentrically braced frames.” Ph.D. dissertation, Univ. of California, San Diego.
Richards, P., and Uang, C. M. (2003). “Development of testing protocol for short links in eccentrically braced frames.” Rep. No. SSRP-2003/08, Structural Systems Research Project, Dept. of Structural Engineering, Univ. of Californi, San Diego, La Jolla, Calif.
Richards, P., and Uang, C. M. (2005). “Effect of flange width-thickness ratio on eccentrically braced frames link cyclic rotation capacity.” J. Struct. Eng., 131(10), 1546–1552.
Richards, P., and Uang, C. M. (2006). “Testing protocol for short links in eccentrically braced frames.” J. Struct. Eng., 132(8), 1183–1191.
Ricles, J. M., and Popov, E. P. (1989). “Composite action in eccentrically braced frames.” J. Struct. Eng., 115(8), 2046–2066.
Roeder, C. W., and Popov, E. P. (1978). “Eccentrically braced steel frames for earthquakes.” J. Struct. Div., 104(3), 391–412.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Jun 15, 2006
Accepted: Apr 9, 2007
Published online: May 1, 2008
Published in print: May 2008
Notes
Note. Associate Editor: Benjamin W. Schafer
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.