Evaluation of 3D Steel Moment Frames under Earthquake Excitations. I: Modeling
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 133, Issue 3
Abstract
For performance evaluation of structural systems under seismic loads, accurate modeling of structural component and system response behavior in the nonlinear range is required. In this study, the differential-equation-based hysteresis (Bouc-Wen) model is incorporated into ABAQUS to describe the inelastic connection behaviors of moment frames, taking into account capacity uncertainties of connections documented in the FEMA/SAC projects. A three-dimensional (3D) finite-element model is developed to examine the effects of bi-axial motions including those due to torsion oscillation. Effects of gravity frames, panel zones, and inelastic column deformation are also considered. Numerical examples are carried out to evaluate displacement demand. System capacity against incipient collapse is determined by the incremental dynamic analysis (IDA). Both inherent variability and modeling error are considered. Results indicate that torsional effects due to asymmetric member failures are important. The conventional lumped-plasticity model limits the development of plasticity of columns, thus is not appropriate in IDA for system capacity analysis. As expected, fracture failures of the pre-Northridge connections have a severe impact on the building performance. The methods of modeling and response analysis developed will be used in the reliability and redundancy study in the companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Support from the National Science Foundation under Grant No. NSFNSF-CMS 02-18703 is gratefully acknowledged.
References
AISC. (2002). “Seismic provisions for structural steel buildings.” ANSI/AISC 341-02, Chicago.
Baber, T. T., and Noori, M. N. (1985). “Random vibration of degrading, pinching systems.” J. Eng. Mech., 111(8), 1010–1026.
Baber, T. T., and Wen, Y. K. (1981). “Random vibration hysteretic, degrading systems.” J. Engrg. Mech. Div., 107(6), 1069–1074.
FEMA. (1997). “Connection test summaries.” Rep. No. FEMA-289, Washington, D.C.
FEMA. (2000a). “Recommended seismic design criteria for new steel moment-frame buildings.” Rep. No. FEMA-350, Washington, D.C.
FEMA. (2000b). “State of art report on connection performance.” Rep. No. FEMA-355D, Washington, D.C.
Foliente, G. C. (1995). “Hysteresis modeling of wood joints and structural systems.” J. Struct. Eng., 121(6), 1013–1017.
Hibbitt, Karlsson, and Sorensen, Inc. (HKS). (2003). ABAQUS version 6.4 Pawtucket, R.I.
Hilber, H. M., Hughes, T. J. R., and Taylor, R. L. (1978). “Collocation, dissipation, and ‘overshoot’ for time integration schemes in structural dynamics.” Earthquake Eng. Struct. Dyn., 6, 99–117.
International Conference of Building Officials (ICBO). (1998). International building code 2000, Boca Raton, Fla.
Kennedy, D. J. L., and Baker, K. A. (1984). “Resistance factors for steel highway bridges.” Can. J. Civ. Eng., 11, 324–334.
Krawinkler, H. (2000). “State of art report on systems performance of moment resisting steel frames subject to earthquake ground shaking.” FEMA 355c, Federal Emergency Management Agency, Washington, D.C.
Liao, K.-W., Wen, Y.-K., and Foutch, D. A. (2007). “Evaluation of 3D steel moment frames under earthquake excitations. II: Reliability and redundancy.” J. Struct. Eng., 133(3), 471–480.
Liu, J., and Astaneh-Asl, A. (2000). “Cyclic tests on simple connections including effects of the slab.” SAC Background Document SAC/BD-00/03, SAC Joint Venture, Richmond, Calif.
Shi, S. (1997). “Evaluation of connection fracture and hysteresis type on the seismic response of steel buildings.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Illinois at Urbana-Champaign, Urbana, Ill.
Shome, N., and Cornell, C. A. (2000). “Structural seismic demand analysis: Consideration of ‘collapse’.” Proc., 8th Annual ASCE Specialty Conf. on Probabilistic Mechanics and Structural Reliability.
Somerville, P., Smith, N., Punyamurthula, S., and Sun, J. (1997). “Development of ground motion time histories for Phase 2 of the FEMA/SAC steel project.” Rep. No. SAC/BD-97/04, Sacramento, Calif.
Vamvatsikos, D., and Cornell, C. A. (2002). “Incremental dynamic analysis.” Earthquake Eng. Struct. Dyn., 31(3), 491–514.
Wang, C.-H., and Wen, Y. K. (2000a). “Evaluation of pre-Northridge low-rise steel buildings. Part I: Modeling.” J. Struct. Eng., 126(10), 1160–1168.
Wang, C.-H., and Wen, Y. K. (2000b). “Evaluation of pre-Northridge low-rise steel buildings. Part II: Reliability.” J. Struct. Eng., 126(10), 1169–1176.
Wen, Y. K. (1976). “Method for random vibration of hysteretic systems.” J. Engrg. Mech. Div., 102(2), 249–263.
Wen, Y. K., and Foutch, D. A. (1997). “Proposed statistical and reliability framework for comparing and evaluating predictive models for evaluation and design and critical issues in developing such framework.” Rep. No. SAC/BD-97/03, FEMA/SAC Steel Project, Sacramento, Calif.
Yang, T.-S., and Popov., E. P. (1995). “Behavior of pre-Northridge moment resisting steel connections.” Rep. No. UCB/EERC-95/08, Earthquake Engineering Research Center, Univ. of California, Berkeley, Berkeley, Calif.
Yun, S. Y., Hamburger, R. O., Cornell, C. A., and Foutch, D. A. (2002). “Seismic performance evaluation for steel moment frames.” J. Struct. Eng., 128(4), 534–545.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jun 10, 2005
Accepted: Jul 31, 2006
Published online: Mar 1, 2007
Published in print: Mar 2007
Notes
Note. Associate Editor: Panos Tsopelas
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.