Cast Modular Panel Zone Node for Steel Special Moment Frames. I: Analytical Development
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 133, Issue 10
Abstract
A panel zone dissipator modular node (PZ-MN) has been developed for use in seismic-resistant steel moment frames. The PZ-MN is configured directly for optimal seismic performance through a casting process. The PZ-MN dissipates energy through stable yielding of the panel zone. This objective is accomplished by mitigating the effects of panel zone distortion on surrounding members and connections. Field welds are removed from critical cross sections and demands are redirected in noncritical paths. A cast piece easily accommodates the geometries and features to meet this objective. The PZ-MN was developed through a comprehensive analytical research program and verified through full-scale experimentation. This paper describes the analytical development stage. Investigation of trial configurations, key parameters, and enhancements resulted in a prototype design for the PZ-MN. The PZ-MN prototype shows the potential for excellent seismic performance, including under the combined effects of lateral and gravity load. This performance is experimentally verified in a companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by NSF CAREER Award Grant No. NSFCMS-01-96120. Supplemental funds were provided by the American Institute of Steel Construction (AISC) and the Steel Founder’s Society of America (SFSA). Industry Partners Varicast, Inc. and Able Steel created the prototype specimens. The reaction frame was provided through a donation by ConXtech, Inc.; the computer laboratory through a grant from Intel, Inc.; finite-element software was donated by industry partner Swanson, Inc. (ANSYS). The writers are grateful for this support. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the writers and do not necessarily reflect the views of the National Science Foundation.
References
American Institute of Steel Construction (AISC). (1997). Seismic provisions for structural steel buildings, Chicago.
American Institute of Steel Construction (AISC). (2002). Seismic provisions for structural steel buildings, Chicago.
ANSYS Inc. (1999). ANSYS user’s manual—Version 5.6, Canonsburg, Pa.
Bertero, V. V., Popov, E. P., and Krawinkler, H. (1972). “Beam-column subassemblages under repeated loading.” J. Struct. Div., 98(5), 1137–1159.
El-Tawil, S., Mikesell, T., and Kunnath, S. K. (2000). “Effect of local details and yield ratio on behavior of FR steel connections.” J. Struct. Eng., 126(1), 79–87.
El-Tawil, S., Vidarsson, E., Mikesell, T., and Kunnath, S. K. (1999). “Inelastic behavior and design of steel panel zones.” J. Struct. Eng., 125(2), 183–193.
Engelhardt, M. D., Winneberger, T., Zekany, A. J., and Potyraj, T. J. (1996). “Dogbone connection: Part II.” Modern Steel Constr., 36(8), 46–55.
Englekirk, R. E. (1999). “Extant panel zone design procedures for steel frames are questioned.” Earthquake Spectra, 15(2), 361–370.
Federal Emergency Management Agency (FEMA). (2000a). “Recommended seismic design criteria for new steel moment-frame buildings.” FEMA-350, prepared by the SAC Joint Venture for the Federal Emergency Management Agency, Washington, D.C.
Federal Emergency Management Agency (FEMA). (2000b). “State of the art report on welding and inspection.” FEMA-355B, prepared by the SAC Joint Venture for the Federal Emergency Management Agency, Washington, D.C.
Federal Emergency Management Agency (FEMA). (2000c). “State of the art report on systems performance of steel moment frames subject to earthquake ground shaking.” FEMA-355C, prepared by the SAC Joint Venture for the Federal Emergency Management Agency, Washington, D.C.
Federal Emergency Management Agency (FEMA). (2000d). “State of the art report on past performance of steel moment-frame buildings in earthquakes.” FEMA-355E, prepared by the SAC Joint Venture for the Federal Emergency Management Agency, Washington, D.C.
Fleischman, R. B., Palmer, N. J., Wan, G., and Li, X. (2007). “Cast modular panel zone node for steel special moment frames. II: Experimental verification and system evaluation.” J. Struct. Eng., 133(10), 1404–1414.
Gupta, A., and Krawinkler, H. (2000). “Behavior of ductile SMRFs at various seismic hazard levels.” J. Struct. Eng., 126(1), 98–107.
International Code Council, Inc. (ICC). (2003). International building code.
Krawinkler, H. (1978). “Shear in beam-column joints in seismic design of steel frames.” Eng. J., 5(3), 82–90.
Krawinkler, H. (1996). “Earthquake design and performance of steel structures.” Bull. N.Z. Natl. Soc. Earthq. Eng., 29(4), 229–241.
Li, X. (2002). “Development of panel zone dissipator modular nodes for seismic resistant steel frames.” MS thesis, Civil Engineering and Engineering Mechancis, Univ. of Arizona, Tucson, Ariz.
Malley, J. O. (1995). “Performance of steel framed buildings in the January 17, 1994 Northridge earthquake.” Proc., Restructuring: America and Beyond, Structures Congress, Vol. 1, ASCE, 320–332.
Popov, E. P., Tsai, K. C., and Engelhardt, M. D. (1989). “On seismic steel joints and connections.” Eng. Struct., 11(4), 148–162.
Richard, R. M., Allen, J., and Partridge, J. E. (2001). “Accumulated seismic connection damage based upon full scale low cycle fatigue connection tests.” Proc., Structural Engineers Association of California (SEAOC) 70th Annual Convention, 43–48.
Richard, R. M., Patridge, J. E., and Allen, J. (1995). “Finite element analyses and tests of beam-to-column connections.” Modem steel construction, AISC, Chicago.
Schafer, B. W., Ojdrovic, R. P., and Zarghamee, M. S. (2000). “Triaxiality and fracture of steel moment connections.” J. Struct. Eng., 126(10), 1131–1139.
Schneider, S. P., and Amidl, A. (1998). “Seismic behavior of steel frames with deformable panel zone.” J. Struct. Eng., 124(1), 35–42.
Structural Engineers Association of California (SEAOC). (1996). Blue book, Sacramento, Calif.
Stojadinovic, B., Goel, S. C., Lee, K.-H., Margarian, A. G., and Choi, H., (2000). “Parametric tests on unreinforced steel moment connections.” J. Struct. Eng., 126(1), 40–49.
Sumer, A., Fleischman, R. B., and Hoskisson, B. (2006). “Development of a cast modular connector for seismic-resistant steel moment frames. Part 1: Prototype development.” Eng. J., in press.
Uniform Building Code. (1994). Int. Conf. of Building Officials, Whittier, Calif.
Varicast. (2002). Steel Casting Mechanical Testing Reports, Portland, Ore.
Watanabe, J., Sugiura, K., Nagata, K., and Kitane, Y. (1998). “Performance and damages to steel structures during the 1995 Hyogoken-Nanbu earthquake.” Eng. Struct., 20(4–6), 148–162.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: May 24, 2005
Accepted: Oct 9, 2006
Published online: Oct 1, 2007
Published in print: Oct 2007
Notes
Note. Associate Editor: Sherif El-Tawil
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.