Disturbed Stress Field Model for Reinforced Concrete: Formulation
This article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 126, Issue 9
Abstract
A conceptual model is presented for describing the behavior of cracked reinforced concrete elements, representing a hybrid formulation between a fully rotating crack model and a fixed crack model. The formulation described builds on the concepts of the modified compression field theory, treating cracked concrete as an orthotropic material with unique stress-strain relationships in compression and tension. Advancements in the formulation, relative to the modified compression field theory, include a new approach to the reorientation of concrete stress and strain fields, removing the restriction that they be coincident, and an improved treatment of shear stresses on crack surfaces. New sets of equilibrium, compatibility, and constitutive relations are formulated accordingly, and alternative crack slip models are discussed. The proposed theory is shown to yield improved simulations of response in specific situations where the previous formulation was found to produce inaccuracies. This paper describes the formulation of the theory at the fundamental level.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ayoub, A., and Filippou, F. C. (1998). “Nonlinear finite element analysis of RC shear panels and walls.”J. Struct. Engrg., ASCE, 124(3), 298–308.
2.
Barzegar-Jamshidi, F., and Schnobrich, W. C. (1986). “Nonlinear finite element analysis of reinforced concrete under short-term monotonic loading.” Civ. Engrg. Studies Rep. No. 530, University of Illinois at Urbana-Champaign, Urbana, Ill.
3.
Bentz, E. C. ( 1999). “Sectional analysis of reinforced concrete structures.” PhD thesis, Dept. of Civ. Engrg., University of Toronto, Toronto.
4.
Bhide, S. B., and Collins, M. P. (1989). “Influence of axial tension on the shear capacity of reinforced concrete members.” ACI Struct. J., 86(5), 570–581.
5.
Canadian Standards Association (CSA) Committee A23.3. (1994). “Design of concrete structures: Structures (design)—A national standard of Canada.” Rexdale, Ont., Canada.
6.
Collins, M. P., Mitchell, D., Adebar, P., and Vecchio, F. J. (1996). “A general shear design method.” ACI Struct. J., 93(1), 36–45.
7.
Foster, S. J. ( 1992). “The structural behavior of reinforced concrete deep beams.” PhD dissertation, University of New South Wales, New South Wales, Australia.
8.
Kaufmann, W., and Marti, P. (1998). “Structural concrete: Cracked membrane model.”J. Struct. Engrg., ASCE, 124(12), 1467–1475.
9.
Kollegger, J., and Mehlhorn, G. (1990). “Experimentelle Untersuchungen zur Bestimmung der Druckfestigkeit des gerissenen Stahlbetons bei einer Querzugbeanspruchung.” Rep. 413, Deutscher Ausschuss für Stahlbeton, Berlin.
10.
Okamura, H., and Maekawa, K. ( 1991). “Nonlinear analysis and constitutive methods of reinforced concrete.” ISBN 7655-1506-0, University of Tokyo, Tokyo.
11.
Vecchio, F. J. (1992). “Finite element modeling of concrete expansion and confinement.”J. Struct. Engrg., ASCE, 118(9), 2390–2406.
12.
Vecchio, F. J. (2000). “Analysis of shear-critical reinforced concrete beams.” ACI Struct. J., 97(1), 102–110.
13.
Vecchio, F. J., and Collins, M. P. (1982). “Response of reinforced concrete to in-plane shear and normal stresses.” Rep. No. 82-03, Dept. of Civ. Engrg., University of Toronto, Toronto.
14.
Vecchio, F. J., and Collins, M. P. (1986). “The modified compression field theory for reinforced concrete elements subjected to shear.” ACI J., 83(2), 219–231.
15.
Vecchio, F. J., and Collins, M. P. (1993). “Compression response of cracked reinforced concrete.”J. Struct. Engrg., ASCE, 119(12), 3590–3610.
16.
Vecchio, F. J., Polak, M. A., and Selby, R. G. (1996). “Nonlinear analysis of reinforced concrete: The University of Toronto experience.” Proc., 3rd Asian-Pacific Conf. on Computational Mech.
17.
Walraven, J. C. (1981). “Fundamental analysis of aggregate interlock.”J. Struct. Engrg., ASCE, 107(11), 2245–2270.
Information & Authors
Information
Published In
History
Received: Aug 10, 1999
Published online: Sep 1, 2000
Published in print: Sep 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.