Influence of Grain Size on Sediment Transport during Initial Stages of Horizontal Dam Break–Type Flows
Publication: Journal of Waterway, Port, Coastal, and Ocean Engineering
Volume 145, Issue 3
Abstract
The influence of grain size on sediment transport during the initial stages of dam break–type flows over horizontal mobile sediment beds was investigated through dimensional analysis and experiments. A new dimensional analysis reconciles the unbalanced dimensions in Bagnold’s formulations describing the grain size influence on steady-flow sediment transport and indicates that the sediment transport is inversely proportional to the square root of the grain size, consistent with Bagnold’s empirical correlation. Total transport rates were measured for quartz grains ranging from 0.22 to 2.65 mm in diameter. Regression between the dimensionless variables indicated that the mobility number collapses the sediment transport data better than the Shields number and indicated that the total sediment transport is approximately inversely proportional to the square root of the grain size and the velocity to the fourth power. The Meyer-Peter Müller transport model based on the Shields number requires transport coefficients for the finest sand that are significantly larger than the conventional values suggested in the literature, between 30 for ks = 2.5D50 and 40 for ks = D50. The values for other sediment sizes are closer to conventional values, within the usual range of 10–12 for ks = 2.5D50, but somewhat higher at 16–22 for ks = D50. The occurrence of sheet flow in a suspension regime appears possible, which may explain the significantly larger transport coefficients required for the finest grain size.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Ilya Othman is indebted to the Ministry of Higher Education of Malaysia and the Universiti Teknologi Malaysia for providing a scholarship and financial support. Zhonglian Jiang and Tom Baldock acknowledge support from the China Scholarship Council and the Australian Research Council through DP110101176 and DP140101302.
References
Asano, T. 1995. “Sediment Transport under Sheet-Flow Conditions.” J. Waterway, Port, Coastal, Ocean Eng. 121 (5): 239–246. https://doi.org/10.1061/(ASCE)0733-950X(1995)121:5(239).
Bagnold, R. A. 1956. “The flow of cohesionless grains in fluids.” Proc. R. Soc. London, Ser. A 249: 235–297.
Bagnold, R. A. 1980. “An empirical correlation of bedload transport rates in flumes and natural rivers.” Proc. R. Soc. London, Ser. A 372 (1751): 453–473. https://doi.org/10.1098/rspa.1980.0122.
Bagnold, R. A. 1986. “Transport of solids by natural water flow: Evidence for a worldwide correlation.” Proc. R. Soc. London, Ser. A 405 (1829): 369–374. https://doi.org/10.1098/rspa.1986.0059.
Baldock, T. E., and P. Nielsen. 2010. “Discussion of ‘effect of seepage-induced nonhydrostatic pressure distribution on bed-load transport and bed morphodynamics’ by Simona Francalanci, Gary Parker, and Luca Solari.” J. Hydraul. Eng. 136 (1): 77–79. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000015.
Barnes, M. P., and T. E. Baldock. 2010. “A Lagrangian model for boundary layer growth and bed shear stress in the swash zone.” Coastal Eng. 57 (4): 385–396. https://doi.org/10.1016/j.coastaleng.2009.11.009.
BMT Group Ltd. 2013. TUFLOW FV Science Manual. Teddington, UK: BMT Group Ltd.
Camenen, B., and M. Larson. 2013. “Accuracy of equivalent roughness height formulas in practical applications.” J. Hydraul. Eng. 139 (3): 331–335. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000670.
Capart, H., and L. Fraccarollo. 2011. “Transport layer structure in intense bed-load.” Geophys. Res. Lett. 38 (20): L20402. https://doi.org/10.1029/2011GL049408.
Capart, H., and D. L. Young. 1998. “Formation of a jump by the dam-break wave over a granular bed.” J. Fluid Mech. 372 (Oct): 165–187. https://doi.org/10.1017/S0022112098002250.
Chanson, H. 2006. “Tsunami surges on dry coastal plains: Application of dam break wave equations.” Coastal Eng. J. 48 (4): 355–370. https://doi.org/10.1142/S0578563406001477.
Cheng, N.-S. 2016. “Representative grain size and equivalent roughness height of a sediment bed.” J. Hydraul. Eng. 142 (1): 06015016. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001069.
Dade, W. B., and P. F. Friend. 1998. “Grain-size, sediment-transport regime, and channel slope in alluvial rivers.” J. Geol. 106 (6): 661–675. https://doi.org/10.1086/516052.
Elfrink, B., and T. Baldock. 2002. “Hydrodynamics and sediment transport in the swash zone: A review and perspectives.” Coastal Eng. 45 (3–4): 149–167. https://doi.org/10.1016/S0378-3839(02)00032-7.
Engelund, F., and E. Hansen. 1967. A monograph on sediment transport in alluvial streams. Copenhagen, Denmark: Teknisk forlag.
Fraccarollo, L., and H. Capart. 2002. “Riemann wave description of erosional dam-break flows.” J. Fluid Mech. 461 (Jun): 183–228. https://doi.org/10.1017/S0022112002008455.
Gomez, B. 2006. “The potential rate of bed-load transport.” Proc. Natl. Acad. Sci. U.S.A. 103 (46): 17170–17173. https://doi.org/10.1073/pnas.0608487103.
Goutiere, L., S. Soares-Frazão, and Y. Zech. 2011. “Dam-break flow on mobile bed in abruptly widening channel: Experimental data.” J. Hydraul. Res. 49 (3): 367–371. https://doi.org/10.1080/00221686.2010.548969.
Hanes, D. M., and A. J. Bowen. 1985. “A granular-fluid model for steady intense bed-load transport.” J. Geophys. Res. C: Oceans 90 (C5): 9149–9158. https://doi.org/10.1029/JC090iC05p09149.
Hogg, A. J., and D. Pritchard. 2004. “The effects of hydraulic resistance on dam-break and other shallow inertial flows.” J. Fluid Mech. 501 (Feb): 179–212. https://doi.org/10.1017/S0022112003007468.
Jiang, Z., and T. E. Baldock. 2015. “Direct bed shear measurements under loose bed swash flows.” Coastal Eng. 100 (Jun): 67–76. https://doi.org/10.1016/j.coastaleng.2015.04.001.
Keulegan, G. H., and L. H. Carpenter. 1958. “Forces on cylinders and plates in an oscillating fluid.” J. Res. Nat. Bur. Stand. 60 (5): 423–440. https://doi.org/10.6028/jres.060.043.
Kikkert, G. A., T. O’Donoghue, D. Pokrajac, and N. Dodd. 2012. “Experimental study of bore-driven swash hydrodynamics on impermeable rough slopes.” Coastal Eng. 60 (Feb): 149–166. https://doi.org/10.1016/j.coastaleng.2011.09.006.
Leal, J. G., R. M. L. Ferreira, and A. H. Cardoso. 2006. “Dam-break wave-front celerity.” J. Hydraul. Eng. 132 (1): 69–76. https://doi.org/10.1061/(ASCE)0733-9429(2006)132:1(69).
Martin, Y., and M. Church. 2000. “Re-examination of Bagnold’s empirical bedload formulae.” Earth Surf. Processes Landforms 25 (9): 1011–1024. https://doi.org/10.1002/1096-9837(200008)25:9%3C1011::AID-ESP114%3E3.0.CO;2-H.
Masselink, G., and M. Hughes. 1998. “Field investigation of sediment transport in the swash zone.” Cont. Shelf Res. 18 (10): 1179–1199. https://doi.org/10.1016/S0278-4343(98)00027-2.
Meyer-Peter, E., and R. Müller. 1948. “Formulas for bed-load transport.” In Proc., 2nd Meeting Int. Association for Hydraulic Structures Research (IAHR), 39–64. Stockholm, Sweden: IAHR.
Nielsen, P. 1992. Coastal bottom boundary layers and sediment transport. Singapore: World Scientific.
Nielsen, P. 2002. “Shear stress and sediment transport calculations for swash zone modelling.” Coastal Eng. 45 (1): 53–60. https://doi.org/10.1016/S0378-3839(01)00036-9.
Nikuradse, J. 1950. Laws of flow in rough pipes. Washington, DC: National Advisory Committee for Aeronautics.
O’Donoghue, T., G. A. Kikkert, D. Pokrajac, N. Dodd, and R. Briganti. 2016. “Intra-swash hydrodynamics and sediment flux for dambreak swash on coarse-grained beaches.” Coastal Eng. 112 (Jun): 113–130. https://doi.org/10.1016/j.coastaleng.2016.03.004.
Othman, I. K. 2014. “Influence of grain size on swash zone sediment transport.” Ph.D. thesis, Univ. of Queensland. https://espace.library.uq.edu.au/view/UQ:320491.
Othman, I. K., T. E. Baldock, and D. P. Callaghan. 2014. “Measurement and modelling of the influence of grain size and pressure gradient on swash uprush sediment transport.” Coastal Eng. 83 (Jan): 1–14. https://doi.org/10.1016/j.coastaleng.2013.09.001.
Postacchini, M., I. K. Othman, M. Brocchini, and T. E. Baldock. 2014. “Sediment transport and morphodynamics generated by a dam-break swash uprush: Coupled vs uncoupled modeling.” Coastal Eng. 89 (Jul): 99–105. https://doi.org/10.1016/j.coastaleng.2014.04.003.
Pritchard, D., and A. J. Hogg. 2002. “On sediment transport under dam-break flow.” J. Fluid Mech. 473 (Dec): 265–274. https://doi.org/10.1017/S0022112002002550.
Pugh, F., and K. Wilson. 1999. “Velocity and concentration distributions in sheet flow above plane beds.” J. Hydraul. Eng. 125: 117–125. https://doi.org/10.1061/(ASCE)0733-9429(1999)125:2(117).
Shields, A. 1936. Anwendung der aehnlichkeitsmechanik und der turbulenzforschung auf die geschiebebewegung. [In German.] Vol 26, Mitteilungen der Preußischen Versuchsanstalt fu¨r Wasserbau und Schiffbau. Berlin: Eigenverl.
Sleath, J. F. A. 1999. “Conditions for plug formation in oscillatory flow.” Cont. Shelf Res. 19 (13): 1643–1664. https://doi.org/10.1016/S0278-4343(98)00096-X.
Spinewine, B., and H. Capart. 2013. “Intense bed-load due to a sudden dam-break.” J. Fluid Mech. 731 (Sep): 579–614. https://doi.org/10.1017/jfm.2013.227.
Spinewine, B., and Y. Zech. 2007. “Small-scale laboratory dam-break waves on movable beds.” J. Hydraul. Res. 45 (Sup 1): 73–86. https://doi.org/10.1080/00221686.2007.9521834.
Stansby, P. K., A. Chegini, and T. C. D. Barnes. 1998. “The initial stages of dam-break flow.” J. Fluid Mech. 374 (Nov): 407–424. https://doi.org/10.1017/S0022112098009975.
Sumer, B. M., A. Kozakiewicz, J. Fredsøe, and R. Deigaard. 1996. “Velocity and concentration profiles in sheet-flow layer of movable bed.” J. Hydraul. Eng. 122 (10): 549–558. https://doi.org/10.1061/(ASCE)0733-9429(1996)122:10(549).
Swamee, P. K., and A. K. Jain. 1976. “Explicit equations for pipe-flow problems.” J. Hydraul. Div. 102: 657–664.
van Rijn, L. C. 1982. “Equivalent roughness of alluvial bed.” J. Hydraul. Div. 108 (10): 1215–1218.
van Rijn, L. C. 1993. Principles of sediment transport in rivers, estuaries, and coastal seas. Amsterdam, Netherlands: Aqua Publications.
Wong, M., and G. Parker. 2006. “Reanalysis and correction of bed-load relation of Meyer-Peter and Müller using their own database.” J. Hydraul. Eng. 132 (11): 1159–1168. https://doi.org/10.1061/(ASCE)0733-9429(2006)132:11(1159).
Wüthrich, D., M. Pfister, I. Nistor, and A. J. Schleiss. 2018. “Experimental study of tsunami-like waves generated with a vertical release technique on dry and wet beds.” J. Waterway, Port, Coastal, Ocean Eng. 144 (4): 04018006. https://doi.org/10.1061/(ASCE)WW.1943-5460.0000447.
Yang, S.-Q., S. K. Tan, and S. Y. Lim. 2005. “Flow resistance and bed form geometry in a wide alluvial channel.” Water Resour. Res. 41 (9): W09419. https://doi.org/10.1029/2005WR004211.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: May 22, 2018
Accepted: Oct 3, 2018
Published online: Mar 1, 2019
Published in print: May 1, 2019
Discussion open until: Aug 1, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.