Influence of Channel Shape on Wave-Generated Parameters by a Pressure Source in Shallow Water
Publication: Journal of Waterway, Port, Coastal, and Ocean Engineering
Volume 143, Issue 5
Abstract
The present work is a numerical investigation into the waves generated by a pressure source moving in straight channels with a nonrectangular cross-channel depth profile. Wave fields generated by the moving pressure source are described, and the effects of channel bathymetry on the generated wave characteristics of wave height, wave-breaking location, wave-breaking type and intensity, and peel angle are presented. Four different channel cross-section shapes were investigated, and the results were analyzed. It was concluded that the maximum wave height depended primarily on pressure-source parameters and that the investigated channel shapes did not have a significant effect on the maximum wave height. All four investigated channels were able to generate plunging-shaped breaking waves. In addition, wave-breaking intensity and barrel shape could be controlled by beach-slope shape; however, beach slope did not have a considerable effect on the wave-breaking location. The width of the deep section of the channel had a significant effect on the breaking location. Widening the deep section of the channel moved the breaking point farther from the pressure source. According to the simulation results, it is possible to generate waves for an intermediate or expert surfer only by changing the pressure-source speed. According to the results, by changing the pressure-source speed, the peel angle changes, which is the best way to change the required skill level for surfing. In addition, changing the channel shape did not have a significant effect on the required skill level for surfing.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank the Australian Research Council (ARC), University of Tasmania, and Liquid Time Pty Ltd., which funded this research. This research was supported under the ARC Linkage Projects funding scheme (Project LP0990307).
References
Andersson, B., et al. (2012). Computational fluid dynamics for engineers, Cambridge University Press, Cambridge, U.K.
ANSYS-Fluent 14.0 [Computer software]. ANSYS, Canonsburg, PA.
Black, K., and Mead, S. (2001). “Predicting the breaking intensity of surfing waves.” J. Coastal Res. Surfing, 51–65.
Chandraprabha, S., and Molland, A. F. (2004). “A numerical prediction of wash wave and wave resistance of high speed displacement ships in deep and shallow water.” Proc., Conf. Mechanical Engineering Network of Thailand.
Driscoll, A., and Renilson, M. R. (1980). “The wavedozer: A system of generating stationary waves in a circulating water channel.” AMTE(H) TM80013, Admiralty Marine Technology Establishment (Haslar), Haslar, U.K.
Ertekin, R. C., Webster, W. C., and Wehausen, J. V. (1986). “Waves caused by a moving disturbance in a shallow channel of finite width.” Fluid Mech., 169, 275–292.
Fontaine, E., and Tulin, M. P. (2001). “On the prediction of nonlinear free-surface flows past slender hulls using 2d+t theory: The evolution of an idea.” Ship Technol. Res., 48, 56–67.
Galvin, C. J., Jr. (1968). “Breaker type classification on three laboratory beaches.” J. Geophys. Res., 73(12), 3651–3659.
Henn, R., Sharma, S. D., and Jiang, T. (2001). “Influence of canal topography on ship waves in shallow water.” Proc., 16th Int. Workshop on Water Waves and Floating Bodies, Office of Naval Research International Field Office, London.
Hutt, J. A., Black, K. P., and Mead, S. T. (2001). “Classification of surf breaks in relation to surfing skill.” J. Coastal Res., 29, 66–81.
Javanmardi, M. (2015). “The investigation of high quality surfing waves generated by a moving pressure source.” Ph.D. thesis, Univ. of Tasmania, Launceston, Australia.
Javanmardi, M., Binns, J., Renilson, M. R., Thomas, G., and Huijsmans, J. (2012). “The formation of surfable waves in a circular wave pool-comparison of numerical and experimental approaches.” Proc., 31st Int. Conf. on Ocean, Offshore and Arctic Engineering, ASME, New York.
Javanmardi, M., Binns, J., Thomas, G., and Renilson, M. R. (2013). “Prediction of water wave propagation using computational fluid dynamics.” Proc., 32nd Int. Conf. on Ocean, Offshore and Arctic Engineering, ASME, New York.
Jiang, T., Henn, R., and Sharma, S. D. (2002). “Wash waves generated by ships moving on fairways of varying topography.” Proc., 24th Symp. on Naval Hydrodynamics, Research Institute for Applied Mechanics, Kyushu Univ., Fukuoka, Japan.
Katsis, C., and Akylas, T. R. (1987). “On the excitation of long nonlinear water waves by a moving pressure distribution: Part 2. Three-dimensional effects.” Fluid Mech., 177, 49–65.
Kim, Y. (2003). “Artificial damping in water wave problems II: Application to wave absorption.” Int. J. Offshore and Polar Eng., 13, 5.
Kofoed-Hansen, H., Jensen, T., Sørensen, O. R., and Fuchs, J. (2000). “Wake wash risk assessment of high-speed ferry routes—A case study and suggestions for model improvements.” Proc., Int. Conf. on Hydrodynamics of High-Speed Craft—Wake Wash and Motion Control, The Royal Institution of Naval Architects, London.
Koushan, K., Werenskiold, P., and Zhao, R. (2001). “Experimental and theoretical investigation of wake wash.” Proc., 6th Annual Conf. on FAST SEA Transportation, The Royal Institution of Naval Architects, Southampton, U.K., 165–179.
Liu, P. L.-F., and Wu, T.-R. (2004). “Waves generated by moving pressure disturbances in rectangular and trapezoidal channels.” J. Hydraul. Res., 42(2), 163–171.
Macfarlane, G. (2012). “Marine vessel wave wake: Focus on vessel operations within sheltered waterways.” Ph.D. thesis, Univ. of Tasmania, Launceston, Australia.
Macfarlane, G., and Cox, G. (2004). “The development of vessel wave wake criteria for the Noosa and Brisbane Rivers in southeast Queensland.” Proc., 5th Int. Conf. on Coastal Environment, WIT, Southampton, U.K.
Macfarlane, G., Cox, G., and Bradbury, J. (2008). “Bank erosion from small craft wave wake in sheltered waterways.” Trans. RINA B: Int. J. Small Craft Tech., 150(B2).
Macfarlane, G. J., and Bose, N. (2012). Wave wake: Focus on vessel operations within sheltered waterways, Society of Naval Architects and Marine Engineers, Alexandria, VA.
Mathew, J., and Akylas, T. R. (1990). “On three-dimensional long water waves in a channel with sloping sidewalls.” Fluid Mech., 215, 289–307.
Mead, S. (2003). “Surfing science.” Proc., 3rd Int. Surfing Reef Symp., ASR Limited, Hamilton, New Zealand.
Mead, S., and Black, K. (2001). “Natural and artificial reefs for surfing and coastal protection.” J. Coastal Res., (29), 5–20.
Muzaferija, S., Peric, M., Sames, P., and Schellin, T. (1998). “A two-fluid Navier-Stokes solver to simulate water entry.” Proc., Int. 22nd Symp. on Naval Hydrodynamics, National Academy Press, Washington, DC.
Nanson, G. C., Krusenstierna, A. V., Bryant, E. A., and Renilson, M. R. (1994). “Experimental measurements of river bank erosion caused by boat-generated waves on the Gordon River, Tasmania.” River Res. Appl., 9(1), 1–14.
Nelson, R. (1997). “Height limits in top down and bottom up wave environments.” Coastal Eng., 32(2–3) 247–254.
Pedersen, G. (1988). “Three-dimensional wave patterns generated by moving disturbances at transcritical speeds.” Fluid Mech., 196, 39–63.
Peregrine, D. H. (1966). “Long waves in a uniform channel of arbitrary cross section.” Fluid Mech., 32(2), 353–365.
Peters, A. S. (1966). “Rotational and irrotational solitary waves in a channel with arbitrary cross-section.” Comm. Pure Appl. Math., 19(4), 445–471.
Raven, H. C. (2000). “Numerical wash prediction using a free-surface panel code.” Proc., Int. Conf. on Hydrodynamics of High-Speed Craft—Wake Wash and Motion Control, The Royal Institution of Naval Architects, London.
Renilson, M. R., and Lenz, S. (1989). “An investigation into the effect of hull form on the wake wave generated by low speed vessels.” Proc., 22nd American Towing Tank Conf., British Maritime Technology, Teddington, U.K.
Robbins, A., Thomas, G., Renilson, M., and Macfarlane, G. (2011). “Subcritical wave wake unsteadiness.” Trans. RINA A: Int. J. Marit. Eng., 153(3), 153–161.
Sayce, A., Black, K. P., and Gorman, R. (1999). “Breaking wave shape on surfing reefs.” Proc., 14th Australian Conf. on Coastal Engineering, National Committee on Coastal and Ocean Engineering, Institute of Engineers, Barton, Australia.
Schmied, S., Binns, J., Renilson, M. R., Thomas, G., Macfarlane, G. J., and Huijsmans, R. (2011). “A novel method for generating continuously surfable waves—Comparison of predictions with experimental results.” Proc., 30th Int. Conf. on Ocean, Offshore and Arctic Engineering, ASME, New York.
Teng, M. H., and Wu, T. Y. (1997). “Effects of channel cross-sectional geometry on long wave generation and propagation.” Phys. Fluid., 9(11), 3368–3377.
Yang, Q., Faltinsen, O. M., and Zhao, R. (2001). “Wash and wave resistance of ships in finite water depth.” Proc., 8th Int. Symp.—PRADs, Practical Design of Ships and Other Floating Structures, Y.-S. Wu, G.-J. Zhou, W.-C. Cui, eds., Vol. 1, Elsevier Science, Amsterdam, Netherlands, 181–196.
Zibell, H. G., and Grollius, W. (1999). “Fast vessels on inland waterways.” Proc., RINA Int. Conf. on Coastal Ships and Inland Waterways, The Royal Institution of Naval Architects, London.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Jan 8, 2016
Accepted: Jan 9, 2017
Published online: May 10, 2017
Published in print: Sep 1, 2017
Discussion open until: Oct 10, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.