Effects of Moored Boats on the Gradually Varied Free-Surface Profiles of River Flows
Publication: Journal of Waterway, Port, Coastal, and Ocean Engineering
Volume 143, Issue 3
Abstract
The last mile of rivers often represents an option worth considering for the development of ports. This is particularly true in coastal areas that are densely developed. The simplest form of a port canal, i.e., boats moored along the banks, is an attractive option for the low investment required and the often acceptable residual wave motion. Some of the major rivers have thousands of boats moored along their banks. The effect of these floaters on the river levels during floods must be taken into account. The authors present a methodology based on the computation of the forces on a single boat or an array of boats that yields a quantification of the effect on the river levels. It essentially provides an iterative procedure for computing the value of the resistance coefficient to be used in hydraulic analysis. Theoretical predictions are satisfactorily confirmed by ad hoc experimental investigation.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge technicians Mr. Mario Nardi and Lucio Matergia.
References
Bathurst, J. (2002). “At-a-site variation and minimum flow resistance for mountain rivers.” J. Hydrol., 269(1–2), 11–26.
Chakrabarti, S., and Cotter, D. (1994). “Tank wall effects on broadside current forces on barge models.” Ocean Eng., 21(5), 489–497.
Chanson, H. (2004). Hydraulics of open channel flow: An introduction: Basic principles, sediment motion, hydraulic modelling, design of hydraulic structures, Butterworth-Heinemann, Amsterdam, Netherlands, 650.
Chaudhry, M. H. (2007). Open-channel flow, Springer Science & Business Media, New York, 523.
Chow, V. T. (1959). Open-channel hydraulics, McGraw-Hill, New York, 680.
DoD (Department of Defense). (1999). “Department of defense handbook, mooring design.” MIL-HDBK-1026/4A, Washington, DC.
DoD (Department of Defense). (2005). “Design: mooring.” UFC 4-159-03, Washington, DC.
Jacobsen, V., and Jones, D. (1987). “Current loads on ships moored in shallow water.” Proc., 19th Annual Offshore Technology Conf., Vol. 4, Offshore Technology Conf., Richardson, TX, 259–268.
Kim, J., Ivanov, V. Y., and Katopodes, N. D. (2012). “Hydraulic resistance to overland flow on surfaces with partially submerged vegetation.” Water Resour. Res., 48(10), W10540.
Lawrence, D. (1997). “Macroscale surface roughness and frictional resistance in overland flow.” Earth Surf. Processes Landforms, 22(4), 365–382.
Lee, K. H., Han, H. S., and Park, S. (2015). “Failure analysis of naval vessel’s mooring system and suggestion of reducing mooring line tension under ocean wave excitation.” Eng. Fail. Anal., 57, 296–309.
Leopardi, M. (2004). “On roughness similarity of hydraulic models.” J. Hydraul. Res., 42(3), 239–245.
Marchi, E. (1961). “Il moto uniforme delle correnti liquide nei condotti chiusi e aperti.” L’Energia Elettrica, 38(4), 289–301 (in Italian).
Nanson, G. C., Von Krusenstierna, A., Bryant, E. A., and Renilson, M. R. (1994). “Experimental measurements of river-bank erosion caused by boat-generated waves on the Gordon river, Tasmania.” Regulated Rivers Res. Manage., 9(1), 1–14.
NavFaC (Naval Facilities Engineering Command). (1985). Fleet moorings, basic criteria and planning guidelines, design manual 26.5, Naval Facilities Engineering Service Center, Washington, DC.
NavFaC (Naval Facilities Engineering Command). (1986). Mooring design physical and empirical data, design manual 26.6, Naval Facilities Engineering Service Center, Washington, DC.
Percival, S., Hendrix, D., and Noblesse, F. (2001). “Hydrodynamic optimization of ship hull forms.” Appl. Ocean Res., 23(6), 337–355.
Petryk, S., and Bosmajian, G. (1975). “Analysis of flow through vegetation.” J. Hydraul. Div., 101(HY7), 871–884.
Rhee, D. S., Woo, H., Kwon, B., and Ahn, H. K. (2008). “Hydraulic resistance of some selected vegetation in open channel flows.” River Res. Appl., 24(5), 673–687.
Righetti, M., and Armanini, A. (2002). “Flow resistance in open channel flows with sparsely distributed bushes.” J. Hydrol., 269(1), 55–64.
Seelig, W. N., Kriebel, D., and Headland, J. (1992). “Broadside current forces on moored ships.” Proc., Civil Engineering in the Oceans V, ASCE, Reston, VA, 326–340.
Wohl, E. E., and Ikeda, H. (1998). “The effect of roughness configuration on velocity profiles in an artificial channel.” Earth Surf. Processes Landforms, 23(2), 159–169.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Feb 22, 2016
Accepted: Jul 29, 2016
Published online: Oct 5, 2016
Discussion open until: Mar 5, 2017
Published in print: May 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.