Near-Field Resuspension Model for a Cutter Suction Dredge
Publication: Journal of Waterway, Port, Coastal, and Ocean Engineering
Volume 138, Issue 3
Abstract
The quantity of resuspended solids (RSS) created during dredging operations is both a production and environmental issue. Numerical models predict the movement of sediment plumes from dredging operations; however, these far-field models need a “source term” as input. The purpose of this work was to generate a “source term” by developing a near-field resuspension model for cutter suction dredging operations. The near-field cutter resuspension model (NFCRM) used a discretized domain to obtain a more accurate velocity structure and incorporated real laboratory data to model the fluid dynamics of the cutter suction dredging environment. A two-dimensional finite-difference method produced temporal evolution of resuspension from the dredging operation. The output of the near-field model clarified dynamics of the cutter-head environment and provided a source term for a far-field model. To develop and verify the near-field model, turbidity and velocity were measured around a 34.3 cm (13.5 in.) diameter cutter head. Turbidity measurements were equated to RSS concentrations. The NFCRM incorporated laboratory data to determine the velocity field and the turbulent diffusion. Settling velocity of sediment was the primary scaling variable. Cutter speed provided a direct relationship to scale the advective field. The Péclet number scaled the diffusive field. Both point-specific and overall source-term resuspension values predicted from the NFCRM were validated with laboratory testing and field data. Conclusions from this research demonstrate that undercutting produced a larger point-specific RSS concentration than overcutting in laboratory testing. RSS concentration was positively correlated with cutter speed and thickness of cut, and inversely correlated with suction flow rate. The NFCRM produced higher point-specific regions of RSS for undercutting but larger mean values of RSS for overcutting. The NFCRM was comparable to all laboratory testing and field data with suitable mean absolute error (MAE) values. Greater accuracy was achieved for overcutting simulations. The NFCRM followed laboratory trends with cutter speed and suction flow rate but did not show a strong correlation with cut thickness. The NFCRM was numerically sensitive to swing speed because of instabilities in the advective field. Future research should investigate different cutter-head designs and three-dimensional modeling.
Get full access to this article
View all available purchase options and get full access to this article.
References
Bridges, T. S., et al. (2008). “The four R’s of environmental dredging: Resuspension, release, residual, and risk.” Dredging Operations and Environmental Research Program, Technical Rep. No. ERDC/EL TR-08-4, Engineer Research and Development Center, Vicksburg, MS.
Burden, R., and Faires, J. (2001). Numerical analysis, Wadsworth Group, Pacific Grove, CA.
Burger, M. (2003). “Mixture forming processes in dredge cutterheads.” Ph.D. dissertation, Delft Univ. of Technology, Delft, Netherlands.
Chapra, S. C. (1997). Surface water quality modeling, McGraw-Hill, New York.
Collins, M. A. (1995). “Dredging-induced near-field resuspended sediment concentrations and source strengths.” Miscellaneous Paper D-95-2, U.S. Army Engineer Waterways Experiment Station, Vicksburg, MS.
Crockett, T. R. (1993). “Modeling near-field sediment resuspension in cutter head suction dredging operations.” M.S. thesis, Univ. of Nebraska, Lincoln, NE.
Dietrich, W. E. (1982). “Settling velocity of natural particles.” Water Resour. Res.WRERAQ, 18(6), 1615–1626.
Hayes, D. (1986). “Development of a near field source strength model to predict sediment resuspension from cutter suction dredges.” M.S. thesis, Mississippi State Univ., Starkville, MS.
Hayes, D. F., Crockett, T. R., Ward, T. J., and Averett, D. (2000). “Sediment resuspension during cutter head dredging operations.” J. Waterway, Port, Coastal, Ocean Eng.JWPED5, 126(3), 153–161.
Hayes, D. F., and Wu, P. (2001). “Simple approach to TSS source strength estimates.” Proc., WEDA XXI and TAMU 33 Annual Conf., Western Dredging Association, Vancouver, WA.
Hayes, D., Raymond, G., and McLellan, T. (1984). “Sediment resuspension from dredging activities.” Proc., Conf., Dredging 84’, ASCE, Reston, VA.
Henriksen, J. (2010). “Near-field sediment resuspension measurement and modeling for cutter suction dredging operations.” Ph.D. dissertation, Texas A&M Univ., College Station, TX.
Henriksen, J., Randall, R., DeJong, P., and Sonye, S. (2007). “Initial experiments and data acquisition for the model dredge carriage.” Proc., 18th World Dredging Congress, WEDA, Vancouver, WA.
Kuo, A., Welch, C., and Lukens, R. (1985). “Dredge induced turbidity plume model.” J. Waterway, Port, Coastal, Ocean Eng., 111(3), 476–494.
Miedema, S. A. (1995). “Production estimation based on cutting theories for cutting water saturated sand.” Proc., 14th World Dredging Congress, WODA, Amsterdam, Netherlands, 255–275.
Mol, A. (1977). Flow in and around a cutter head: Part III, flow in a cutter head with an artificial breach, injections with pieces of plastic, Delft Hydraulics Laboratory, Delft, Netherlands.
Montgomery, R., and Raymond, G. (1984). “Overview of corps research program on dredging contaminated sediments.” Proc., 8th U.S./Japan Experts Meeting, U.S. Army Engineer Water Resources Support Center, Ft. Belvoir, VA.
Munson, B. R., Young, D. F., and Okiisi, T. H. (2002). Fundamentals of fluid mechanics, 4th Ed., Wiley, New York.
Nakai, O. (1978). “Turbidity generated by dredging projects.” Proc., 3rd U.S./Japan Experts Meeting, U.S. Army Engineer Water Resources Support Center, Ft. Belvoir, VA.
Randall, R., DeJong, P., Sonye, S., Krippner, N., and Henriksen, J. (2005). “Laboratory dredge carriage for modeling dredge operations.” Proc., Western Dredging Association 25th Technical Conf. and 37th Annual Texas A&M Dredging Seminar, Texas A&M Univ., Center for Dredging Studies, Ocean Engineering Program, Civil Engineering Dept., College Station, TX.
Wu, P. Y., and Hayes, D. F. (2000). “Verification and enhancement of TSS source strength models for cutter dredges.” World Dredging, Min., Constr., 36(6).
Yagi, T., et al. (1975). “Effect of operating conditions of hydraulic dredges on dredging capacity and turbidity.” Technical Note 228, Port and Harbour Research Institute, Ministry of Transport, Yokosuka, Japan.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Nov 27, 2010
Accepted: Aug 30, 2011
Published online: Aug 30, 2011
Published in print: May 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.