Numerical Modeling of Load and Stress on the Contact Surface of a Turnout and a Railway Vehicle
Publication: Journal of Transportation Engineering
Volume 139, Issue 5
Abstract
In operating conditions, railroads are subject to abrasive and fatigue wear. Their durability period depends on the properties of the materials from which rail sections are made, the characteristics and value of the load, and the distribution of contact stresses and strain in the places at which wheels contact track and turnout components. Forecasting of the real load and the resultant contact stress and strain makes it possible to rationally design railway turnouts and correctly select the material to be used for their components. For these reasons, characteristics of load and, subsequently, distributions of contact stresses and deformations in places of wheel/turnout-component contact were determined in numerical calculations using Universal Mechanism and MSC.MARC computer applications. It was determined that the distributions of contact and reduced stresses depend on the load value. The highest reduced stresses occur in the contact zone and right under the rolling surface of the section.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The presented results were obtained within Project No. PBU-70/RM2/2011, which was completed using the resources of the National Science Centre.
References
Ahlstrom, J., and Karlsson, B. (2005). “Fatigue behaviour of rail steel: A comparison between strain and stress controlled loading.” Wear, 258(7–8), 1187–1193.
Giannakos, K. (2010). “Loads on track, ballast fouling, and life cycle under dynamic loading in railways.” J. Transp. Eng., 136(12), 1075–1084.
Herian, J., and Aniołek, K. (2008). “The structure and properties of steel with different pearlite morphology and its resistance to abrasive wear.” Arch. Mater. Sci. Eng., 31(2), 83–86.
Herian, J., and Aniołek, K. (2010). “Abrasive wear of railway sections of steel with a different pearlite morphology in railroad switches.” J. Achiev. Mater. Manuf. Eng., 43(1), 236–243.
Knothe, K., Theiler, A., and Guney, S. (1999). “Investigation of contact stresses on the wheel/rail-system at steady state curving.” Proc., 16th IAVSD Symp., Dynamics of Vehicles on Roads and on Tracks (Supplement to Vehicle System Dynamics), Taylor and Francis, New York, 616–628.
Kovalev, R., and Pogorelov, D. (2003). “On some approaches for optimization of railway vehicle dynamics.” Proc., Int. Congress Mechanics and Tribology of Transport Systems (Mechtribotrans 2003), Book 1, Rostov State Univ. of Transport Communication, Rostov-on-Don, Russia, 369–371.
Kuminek, T. (2005) “The influence of wheel profile on cooperation of elements of the system: Wheel-rail.” Ph.D. thesis, Silesian Univ. of Technology, Katowice.
Markine, V., Steenbergen, M., and Shevtsov, I. (2009). “A dynamic model for analysis of damage of railway switches.” Proc., 21st Int. Symp., Dynamics of Vehicles on Roads and Tracks, Taylor and Francis, New York, 1–13.
Modi, O. P., Mondal, D. P., Prasad, B. K., Singh, M., and Khaira, H. K. (2003). “Abrasive wear behaviour of a high carbon steel: Effects of microstructure and experimental parameters and correlation with mechanical properties.” Mater. Sci. Eng., A343(1–2), 235–242.
MSC.Adams/VI-Rail [Computer software]. Marburg, Germany, VI-Grade.
MSC.MARC [Computer software]. Santa Ana, CA, MSC Software.
MSC.visualNastran for Windows [Computer software]. Santa Ana, CA, MSC Software.
Pogorelov, D. (2003). “Computer-aided modeling railroad vehicle dynamics.” Proc., Int. Congress Mechanics and Tribology of Transport Systems (Mechtribotrans 2003), Book 2, Rostov State University of Transport Communication, Rostov-on-Don, Russia, 171–176.
Sitarz, M., Sładkowski, A., and Żurek, Z. (2003). “Research of influence of surface profiles for different wheel-rail pair on distribution of contact stresses.” Proc., 6th Int. Conf. on Contact Mechanics and Wear of Rail/Wheel Systems, CHARMEC/Chalmers University of Technology, Gothenburg, Sweden, 259–264.
Sitarz, M., Wojdyła, T., and Witaszek, M. (1999). “The forces and contact stresses in wheel- rail system.” Proc., Int. Congress Mechanics, Kowno, 230–235.
Sładkowski, A., and Sitarz, M. (2003). “Modelling of contact for a wheel-rail pair.” Proc., 4th Int. Conf., Transbaltica 03, Technika, Vilnius, Lithuania, 483–489.
Universal Mechanism 4.0 [Computer software]. Bryansk, Russia, Laboratory of Computational Mechanics.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jul 9, 2012
Accepted: Oct 19, 2012
Published online: Oct 20, 2012
Published in print: May 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.