Short- and Long-Term Evaluation of Asphalt Concrete Strain Gauge Installation Methods Applied to the KHCTR
Publication: Journal of Transportation Engineering
Volume 138, Issue 6
Abstract
In the present study, three strain gauge installation methods (mound, trench-cut, and block-out) are evaluated to propose a set of methods that are appropriate for different layers of hot mix asphalt (HMA) pavements. The block-out method is also improved to minimize strain gauge mislocations (i.e., installation offsets). Field tests show that the improved block-out method is suitable for most layers, except for a thin surface, for which the mound should be used. To validate the proposed methods, 374 strain gauges are installed at different layers of thirty-three HMA pavement sections (48 in surface, 157 in intermediate, and 169 in base) at the Korea Highway Corporation Test Road (KHCTR) and their initial and long-term performances are monitored at different times. In addition, the failure rates of the embedded strain gauges are correlated with the evolution of the overall pavement conditions and key distresses at selected sections from 2003 to 2007.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors of this paper would like to thank the members of the research institute of Korea Highway Corporation (KHC) for their technical support and help with this research.
References
Al-Qadi, I. L., Loulizi, A., Elseifi, M., and Lahouar, S. (2004). “The Virginia Smart Road: The impact of pavement instrumentation on understanding pavement performance.” J. Assoc. Asphalt Paving Technol.JAAPGG, 73, 427–466.
Baker, H. B., Buth, M. R., and Van Deusen, D. A. (1994). “Minnesota road research project load response instrumentation installation and testing procedures.” Report No. MN/PR-94/01, Minnesota Dept. of Transportation, St. Paul, MN.
Dore, G., Duplain, G., and Pierre, P. (2007). “Monitoring mechanical response of in-service pavements using retrofitted fiber optic sensors.” Proc., Advanced Characterizations of Pavement and Soil Engineering Materials, Taylor & Francis, New York.
Epps, J., et al. (1998). “WesTrack performance-interim findings.” J. Assoc. Asphalt Paving Technol.JAAPGG, 67, 738–782.
Galal, K., Sharp, S. R., and Elfino, M. K. (2007). “Fiber-optic sensors strain measurements under an asphalt layer during and after construction.” Proc., TRB 79th Annual Meeting, Transportation Research Board, National Research Council, Washington, DC.
Kang-won National Univ. (KNU). (2001). “Laboratory and field validations on sensors for pavement sections at KHCTR.” Final Report submitted to KHC, Dept. of Civil Engineering at Kang-won National Univ., Chuncheon, Korea.
Korea Highway Corporation (KHC). (2002). “A study on the construction and management of Korea highway test road.” Final Report PA-02-08, Highway &Transportation Research Institute, Seongnam, Korea.
Korea Highway Corporation (KHC). (2006). “Development of long term performance prediction model for asphalt pavements using the KHC test road data.” Final Report PA-06-18, Highway & Transportation Research Institute, Seongnam, Korea.
Masri, S. F., Agbabian, M. S., Abdel-Ghaffar, A. M., Higazy, M., Claus, R. O., and de Vries, M. J. (1994). “Experimental study of embedded fiber-optic strain gauges in concrete structures.” J. Eng. Mech.JENMDT, 120(8), 1696–1717.
Pierre, P., Dore, G., and Prophete, F. (2004). “Characterization of the impact of tires on pavement behavior.” Can. J. Civ. Eng.CJCEB8, 31(5), 860–869.
Sargand, S. M. (1994). “Development of an instrumentation plan for the Ohio SPS test pavement.” Final Report, The Ohio Research Institute for Transportation and the Environment (ORITE), Ohio Univ., Athens, OH.
Seo, Y., El-Haggan, O., King, M., Lee, S., and Kim, Y. R. (2007). “Air void models for the dynamic modulus, fatigue cracking, and rutting of asphalt concrete.” J. Mater. Civ. Eng.JMCEE7, 19(10), 874–883.
Seo, Y. (2010a). “Distress evolution in highway flexible pavements: A 5-year study at the KHC test road.” J. Test. Eval.JTEVAB, 38(1), 32–41.
Seo, Y. (2010b). “A full scale in-situ evaluation of strain anisotropy at highway flexible pavements.” J. Test. Eval.JTEVAB, 38(4), 383–389.
Timm, D. H, Priest, A. L., and McEwen, T. V. (2004). “Design and instrumentation of the structural pavement experiment at the NCAT test track, NCAT Report No.04-01, National Center for Asphalt Technologists, Auburn, AL.
Tokyo Sokki Kenkyuio Co. (TML). (2010). Precise & flexible strain gauges, product brochure, 〈www.tml.jp〉 (Dec. 21, 2010).
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Jun 12, 2011
Accepted: Dec 1, 2011
Published online: Dec 7, 2011
Published in print: Jun 1, 2012
Published ahead of production: Jun 15, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.