Integrated Stochastic Approach for Risk and Service Estimation: Passing Sight Distance Application
Publication: Journal of Transportation Engineering
Volume 138, Issue 5
Abstract
The geometric design of highway elements is based on a set of standards that do not consider the risk levels associated with these designs. Safety elements including risk measures need to be identified and incorporated into the design process. The focus of this paper is a procedure that can be used by practitioners as a framework to conduct trade-off analyses between risk and service measures of specific design elements. The procedure builds on the randomness of parameters affecting the design attributes of any highway element. By accounting for the inherent variability of the determining parameters, random distributions of the design element can be derived. Then, using stochastic simulation, each of the design values can be tested to assess its risk measures. As a result, a risk index can then be attached to every design value in the random distribution. Finally, level of service (LOS) measures can be estimated and a trade-off analysis between LOS and safety could be conducted. The application focused on the design of the passing sight distance (PSD), which is an example of a highway element traditionally analyzed with no risk measures. Within the analysis, the risks and LOS measures associated with the use of the current PSD standards were assessed. The American Association of State Highways and Transportation Officials (AASHTO) Green Book values were shown to be conservative. The Manual on Uniform Traffic Control Devices (MUTCD) values fall within the acceptable risk and level of service (LOS) levels.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Association of State Highways and Transportation Officials (AASHTO). (2004). A policy on geometric design of highways and street, Washington, DC.
El Khoury, J., and Hobeika, A. (2007a). “Incorporating uncertainty into the estimation of the passing sight distance requirements.” Comput. Aided Civ. Infrastruct. Eng., 22(5), 347–357.
El Khoury, J., and Hobeika, A. (2007b). “Assessing the risk in the design of passing sight distances.” J. Transp. Eng., 133(6), 370–377.JTPEDI
Fambro, B. D., Fitzpatrick, K., and Koppa, R. J. (1998). Transportation research circular E-C003: A new stopping sight distance model for use in highway geometric design, TRB National Research Council, Washington, DC.
Fambro, D. B., Koppa, R. J., Picha, D. L., and Fitzpatrick, K. (2000). “Driver braking performance in stopping sight distance situations.” Transportation Research Record 1701, Transportation Research Board, Washington, DC, 9–16.
Federal Highway Administration. (2000). Manual on uniform traffic control devices for streets and highways, Washington, DC.
Glennon, J. C. (1988). “New and improved model of passing sight distance on two lane highways.” Transportation Research Record 1195, Transportation Research Board, Washington, DC.
Halati, A., Lieu, H., and Walker, S. (1997). “CORSIM-corridor traffic simulation model.” Traffic congestion and traffic safety in the 21st century: Challenge, innovations, and opportunities, ASCE, New York, 570–576.
Harwood, D. W., and Glennon, J. C. (1989). “Passing sight distance design for passenger cars and trucks.” Transportation Research Record 1208, Transportation Research Board, Washington, DC, 59–69.
Lerner, N., Huey, R. W., McGee, H. W., and Sullivan, A. (1995). Older driver perception-reaction time for intersection sight distance and object detection, vol. I: Final report, Federal Highway Administration, U.S. Dept. of Transportation, Washington, DC.
Office of the Highway Policy. (2002). Highway statistics 2002, U.S. Dept. of Transportation, Federal Highway Administration, Washington, DC.
Polus, A., Livneh, M., and Frischer, B. (2000). “Evaluation of the passing process on two lane rural highways.” Transportation Research Record1701, Transportation Research Board, Washington, DC, 53–60.
Rakha, H., Snare, M., and Dion, F. (2004). “Vehicle dynamics model for estimating maximum vehicle acceleration.” Transportation Research Record 1883, Transportation Research Board, Washington, DC, 40–49.
Transportation Research Board. (2000). Highway capacity manual, National Academies of Science, Washington, DC.
U.S. Census Bureau. (2004). 1997 economic census: Vehicle inventory and use survey, Washington, DC.
Information & Authors
Information
Published In
Journal of Transportation Engineering
Volume 138 • Issue 5 • May 2012
Pages: 571 - 579
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Apr 7, 2011
Accepted: Oct 4, 2011
Published online: Oct 6, 2011
Published in print: May 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.