Effect of Mixture Characteristics on Cooling Rate of Asphalt Pavements
Publication: Journal of Transportation Engineering
Volume 135, Issue 5
Abstract
This paper is aimed at estimating the time available for compaction of a hot-mix asphalt mixture during night construction. Laboratory tests were conducted on dense-graded and porous asphalt (PA) mixtures to evaluate their mechanical properties. Temperatures and mix characteristics tested in the laboratory were determined to be those typically found in an asphalt lift from initial laydown through final compaction. In field, thermocouples were installed at different depths to measure temperature changes to decide pavement cooling times of the same mixes as used in the laboratory. The cooling behavior of asphalt concrete could be classified into the following three stages: rapid, transition and stable zone. The air void in the PA mix was found to contribute to heat loss and result in a rapid cooling rate when compared to that in a dense-graded mix. The cooling rate at depth of 0, 2.5, and showed an essential difference in the cooling rate initially. As the cooling process continued, the cooling rate became stable and reached a thermal equilibrium condition. An increase in lift thickness was shown to increase the compaction time. However, an increase in layer thickness more than might not increase the time available for compaction significantly. A regression model was developed to predict the time required to cool to the minimum temperature allowed for compaction at night. The predicted values were in good agreement with those measured in the field. This study shows that a simplified method to predict available compaction time can be developed by considering only the significant factors affecting pavement cooling.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to thank the National Science Council for financially supporting this research under Contract No. NSCTNSC 94-2211-E-012-001.
References
AASHTO. (2000). Hot-mix asphalt paving handbook, Washington, D.C.
Çengel, Y. (2003). Heat transfer: A practical approach, 2nd Ed., McGraw-Hill, New York.
Dickson, P. F., and Corlew, J. S. (1970). “Thermal computations related to the study of pavement compaction cessation requirements.” Proc., Association of Asphalt Paving Technologists, Vol. 39, St. Paul, Minn., 377–403.
Diefenderfer, B. K., Al-Qadi, I. L., and Diefenderfer, S. D. (2006). “Model to predict pavement temperature profile: Development and validation.” J. Transp. Eng., 132(2), 162–167.
Foster, C. R. (1970). “A study of cessation requirements for constructing hot mix asphalt pavements.” Highway Research Record. 307, Highway Research Board, Washington, D.C., 70–75.
Highway Research Board (HRB). (1972). “State of the art: Compaction of asphalt pavements,” Highway Research Board Special Rep. No. 131, Washington, D.C.
Holman, J. P. (1997). Heat transfer, 8th Ed., McGraw-Hill, New York.
Hughes, C. S. (1989). NCHRP synthesis of Highway Practice 152: Compaction of asphalt pavement, Transportation Research Board, Washington, D.C.
Kennedy, T. W., Robert, F. L., and McGennis, R. B. (1984). “Effects of compaction temperature and effort on the engineering properties of asphalt concrete mixtures.” ASTM STP829, Philadelphia, 48–66.
Mahoney, J. P., Muench, S. T., Pierce, L. M., Read, S. A., Jakob, H., and Moore, R. (2000). “Construction-related temperature differentials in asphalt concrete pavement: Identification and assessment.” Transportation Research Record. 1712, Transportation Research Board, Washington, D.C., 93–100.
McLeod, N. W. (1967). “Influence of viscosity of asphalt cements on compaction of paving mixture in the field.” Highway Research Record. 158, Transportation Research Board, Washington, D.C., 76–111.
Mrawira, D. M., and Luca, J. (2006). “Effect of aggregate type, gradation and compaction level on thermal properties of hot-mix asphalt.” Can. J. Civ. Eng., 33(2), 1410–1417.
Neter, J., Wasserman, W., and Whitmore, G. A. (1993). Applied statistics, 4th Ed., Allyn and Bacon, Boston.
Roberts, F. L., Kandhal, P. S., Brown, E. R., Lee, D. Y., and Kennedy, T. W. (1996). Hot mix asphalt materials, mixture design, and construction, 2nd Ed., NAPA Research and Education Foundation, Lanham, Md.
Scherocman, J. A., and Martenson, E. D. (1984). “Placement of asphalt concrete mixtures.” ASTM STP829, Philadelphia, 3–27.
Solaimanian, M., and Kennedy, T. W. (1993). “Predicting maximum pavement surface temperature using maximum air temperature and hourly solar radiation.” Transportation Research Record. 1417. Transportation Research Board, D.C., 1–11.
Tan, S. A., Fwa, T. F., and Chuai, C. T. (1997). “Determination of thermal properties of pavement materials and unbound aggregates by transient heat conduction.” J. Test. Eval., 25(1), 15–22.
Tegeler, P. A., and Dempsey, B. J. (1973). “A method of predicting compaction time for hot-mix bituminous concrete.” Proc. Association of Asphalt Paving Technologists, Vol. 42, St. Paul, Minn., 499–523.
Timm, D. H., Voller, V. R., Lee, E. B., and Harvey, J. (2001). “CalCool: A multi-layer asphalt pavement cooling tool for temperature prediction during construction.” Int. J. Pavement Eng., 2(2), 169–185.
Wolfe, R. K., Heath, G. L., and Colony, D. C. (1983). “Cooling curve prediction of asphaltic concrete.” J. Transp. Eng., 109(1), 137–147.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Mar 24, 2008
Accepted: Sep 29, 2008
Published online: May 1, 2009
Published in print: May 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.