Seismic Performance of M-Section Cold-Formed Thin-Walled Steel-Reinforced Concrete Wall
Publication: Journal of Structural Engineering
Volume 148, Issue 9
Abstract
To overcome the shortcomings of traditional shear walls, structure systems have been proposed and investigated. One such structure system is a steel-reinforced concrete shear wall, which has certain desirable properties such as good load-bearing capacity, stiffness, and seismic performance. This paper proposes an M-section cold-formed thin-walled steel reinforced concrete (MCTSR) shear wall, which uses M-section cold-formed thin-walled steel to function as reinforcements. Six specimens with different permanent formwork types, axial compression ratios, reinforcement diameters, and other parameters were tested under cyclic loading to investigate seismic performance. The results demonstrate that various types of permanent formwork, including cement fibrolite plate, metal lathing, and polystyrene board can meet the requirement of related seismic design codes, construction demand, and assembly requirements, and have no obvious impact on the ultimate load-bearing capacity, lateral stiffness, and stiffness degradation rate. However, it changes the energy dissipation capacity and ductility, which are two important indexes to evaluate seismic performance in engineering practice. The failure mechanism and the influence of axial compression ratio, reinforcement diameter, and space between reinforcements are discussed. The shear-strength equations proposed by various countries’ or regions’ codes were analyzed, which can be used as a reference for related engineers and designers. Finite-element models for MCTSR shear walls were established for further investigation.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The research described in this paper was conducted at the Beijing Higher Institution Engineering Research Center of Civil Engineering Structure and Renewable Material, Beijing Advanced Innovation Center for Future Urban Design, Beijing University of Civil Engineering and Architecture. The research is supported by the Project of National Natural Science Foundation of China (Project No. 51308026) and the Fundamental Research Funds for the Municipal Universities (Project No. X18099). Special thanks are due to the technical staff of the Structural Lab of Beijing University of Civil Engineering and Architecture.
References
ACI (American Concrete Institute). 2011. Building code requirements for structural concrete. ACI 318-11. Bernardino, CA: ACI.
Astaneh-Asl, A. 2002. Seismic behavior and design of composite steel plate shear walls. Berkeley, CA: Structural Steel Educational Council.
Beghini, L. L., A. Beghini, W. F. Baker, and G. H. Paulino. 2015. “Integrated discrete/continuum topology optimization framework for stiffness or global stability of high-rise buildings.” J. Struct. Eng. 141 (8): 04014207. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001164.
CEN (European Committee for Standardization). 1992. Design of concrete structures—Part 1-1: General rules and rules for buildings. Eurocode 2. Brussels, Belgium: CEN.
Chu, M., P. Feng, and L. Ye. 2011. “Analytical model for predicting shear strength of cold-formed thin-walled steel reinforced concrete shear walls.” J. Build. Struct. 32 (9): 107–114.
Dan, D., A. Fabian, and V. Stoian. 2011. “Theoretical and experimental study on composite steel–concrete shear walls with vertical steel encased profiles.” J. Constr. Steel Res. 67 (5): 800–813. https://doi.org/10.1016/j.jcsr.2010.12.013.
Dong, H., J. Feng, and W. Cao. 2012. “Development and research in seismic performance of steel-concrete composite shear wall.” J. Earthquake Eng. Eng. Vibr. 32 (1): 54–61.
Emori, K. 2002. “Compressive and shear strength of concrete filled steel box wall.” Int. J. Steel Struct. 2 (1): 29.
Fan, J., Y. Shen, and B. Zhang. 2006. “Experimental investigation on mechanical behavior of steel reinforced concrete beams.” J. Nanjing Univ. Sci. Technol. 30 (6): 709–713.
Hajjar, J. F. 2001. “Composite construction for wind and seismic engineering.” In Proc., Annual Technical Session, and Meeting, Structural Stability Research Council, 209–228. Gainesville, FL: Structural Stability Research Council.
Herrera, M. M., and J. Porras. 2010. “Behavior of cold-formed thin steel sections (MM) under concentrated loads.” Ingeniería E Investigación 26 (3): 12–25.
Kalali, H., T. G. Ghazijahani, M. Hajsadeghi, T. Zirakian, and F. J. Alaee. 2017. “Numerical study on steel shear walls with sinusoidal corrugated plates.” Lat. Am. J. Solids Struct. 13 (15): 2802–2814. https://doi.org/10.1590/1679-78252837.
Miao, Y., Z. Chen, and Y. Su. 2010. “Experimental study on seismic behavior of steel reinforced high strength concrete short pier shear wall.” Build. Struct. 40 (8): 99–1028.
Ministry of Housing and Urban-Rural Development of the People’s Republic of China. 1996. Specification of testing methods for earthquake resistant building. JGJ 101-1996. Beijing: Ministry of Housing and Urban-Rural Development of the People’s Republic of China.
Ministry of Housing and Urban-Rural Development of the People’s Republic of China. 2010. Technical specification for concrete structures of tall building. JGJ 3-2010. Beijing: Ministry of Housing and Urban-Rural Development of the People’s Republic of China.
Ministry of Housing and Urban-Rural Development of the People’s Republic of China. 2015. Code for design of concrete structures. GB 50010-2010. Beijing: Ministry of Housing and Urban-Rural Development of the People’s Republic of China.
NZS (Standards New Zealand). 2006. Concrete structures standard. The design of concrete structures. NZS 3101:2006. Wellington, New Zealand: NZS.
Park, R. 1988. “State of the art report-ductility evaluation from laboratory and analytical testing.” In Proc., 9th World Conf. on Earthquake Engineering. Tokyo: International Association of Exhibitions and Events.
Phillips, A. R., and M. R. Eatherton. 2018. “Computational study of elastic and inelastic ring shaped—Steel plate shear wall behavior.” Eng. Struct. 177 (Dec): 655–667. https://doi.org/10.1016/j.engstruct.2018.10.008.
Qian, X., and A. Astaneh-Asl. 2018. “Seismic design and behavior of a new high-performance steel plate shear wall system.” In Proc., Paper Presented at the 11th National Conf. on Earthquake Engineering 2018: Integrating Science, Engineering, and Policy, NCEE 2018. Oakland, CA: Earthquake Engineering Research Institute.
Sabouri-Ghomi, S., and S. Sajjadi. 2012. “Experimental and theoretical studies of steel shear walls with and without stiffeners.” J. Constr. Steel Res. 75 (Aug): 152–159. https://doi.org/10.1016/j.jcsr.2012.03.018.
Shafaei, S., A. Ayazi, and F. Farahbod. 2016. “The effect of concrete panel thickness upon composite steel plate shear walls.” J. Constr. Steel Res. 117 (Feb): 81–90. https://doi.org/10.1016/j.jcsr.2015.10.006.
van de Lindt, J. W., and T. N. Dao. 2007. “Evolutionary algorithm for performance-based shear wall placement in buildings subjected to multiple load types.” J. Struct. Eng. 133 (8): 1156–1167. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:8(1156).
Xiao, Q. 2020. Experimental study on seismic behaviors of an innovative adaptive splitting composite shear wall with super high axial compression ratio. Shenzhen: Shenzhen Univ.
Xing-Wen, L., B. Liang, Y. Hong-Lou, D. Ming-Ke, and Z. Xing-Hu. 2010. “Experimental study on the seismic behavior of high performance steel-concrete shear walls.” Eng. Mech. 27 (10): 131–138.
Xu, Z., Z. Chen, B. H. Osman, and S. Yang. 2018a. “Seismic performance of high-strength lightweight foamed concrete-filled cold-formed steel shear walls.” J. Constr. Steel Res. 143 (Apr): 148–161. https://doi.org/10.1016/j.jcsr.2017.12.027.
Xu, Z., Z. Chen, and S. Yang. 2018b. “Seismic behavior of cold-formed steel high-strength foamed concrete shear walls with straw boards.” Thin Walled Struct. 124 (Mar): 350–365. https://doi.org/10.1016/j.tws.2017.12.032.
Zhong, F., X. Liu, and Y. Huang. 2011. “The up to date development on design and research of shear wall in high-rise buildings.” Build. Struct. 41 (4): 33–43.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Nov 16, 2020
Accepted: May 9, 2022
Published online: Jul 15, 2022
Published in print: Sep 1, 2022
Discussion open until: Dec 15, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.