Lateral Torsional Buckling Response of Compact I-Shaped Welded Steel Girders
Publication: Journal of Structural Engineering
Volume 148, Issue 10
Abstract
Recent studies investigating lateral torsional buckling suggest that North American steel design provisions may overestimate the bending resistance of welded girders that buckle laterally in the inelastic range. Furthermore, these provisions do not distinguish between rolled and welded members, but welded girders are widely suspected of possessing unfavorable residual stress distributions that may cause them to be more susceptible to lateral torsional buckling than their rolled counterparts. However, lack of sufficient supporting experimental test data may render existing analytically based assessments of the design equations inadequate. To address the paucity of physical testing, an experimental program was developed to determine the lateral torsional buckling resistance of full-scale I-shaped welded three-plate steel girders fabricated with current shop processes. This paper describes the development of the test program and a unique girder-stability test bed. Test results for seven girders, including measured initial geometric imperfections, load–displacement responses, and moment capacities, are then presented. A finite-element model of the test specimens, validated against the test data, is finally used to investigate the adequacy of the beam design provisions specified in the Canadian and US steel design standards. The results confirm that the current design equations can accurately predict the moment resistance of compact welded steel girders that fail in either the elastic or inelastic lateral torsional buckling mode.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This research was funded by the Natural Sciences and Engineering Research Council (NSERC) of Canada and the CISC Centre for Steel Structures Education and Research at the University of Alberta. All plate material for the girders was donated by SSAB and fabrication of the girders and ancillary testing fixtures was completed by Supreme Group. These contributions are gratefully acknowledged. Finally, the authors wish to thank the reviewers for their cogent and constructive comments, which improved the quality of the paper.
References
AISC. 2016. Specification for structural steel buildings. ANSI/AISC 360-16. Chicago, IL: American Institute of Steel Construction.
Arasaratnam, P. 2005. Characteristics and behavior of plasma cut-welded H-shaped steel columns. Hamilton, ON: McMaster Univ.
ASTM. 2018. Standard test methods and definitions for mechanical testing of steel products. ASTM A370-18. West Conshohocken, PA: ASTM.
Ballio, G., and F. Mazzolani. 2013. Theory and design of steel structures. New York: Chapman and Hall.
Boissonnade, N., and H. Somja. 2012. “Influence of imperfections in FEM modeling of lateral torsional buckling influence of imperfections in FEM modeling of lateral torsional buckling.” In Proc., Annual Stability Conf., 1–15. Grapevine, TX: Structural Stability Research Council.
Chernenko, D. E., and D. J. L. Kennedy. 1991. “An analysis of the performance of welded wide flange columns.” Can. J. Civ. Eng. 18 (4): 537–555. https://doi.org/10.1139/l91-067.
Crisfield, M. A. 1981. “A fast incremental/iterative solution procedure that handles Snap-through.” In Proc., Symp. on Computational Methods in Nonlinear Structural and Solid Mechanics, 55–62. Crowthorne, Berkshire: Transport and Road Research Laboratory.
CSA (Canadian Standards Association). 2013. General requirements for rolled or welded structural quality steel/Structural quality steel. Missisauga, ON, Canada: CSA.
CSA (Canadian Standards Association). 2018. Welded steel construction (metal arc welding). Missisauga, ON, Canada: CSA.
CSA (Canadian Standards Association). 2019a. Canadian highway bridge design code. Missisauga, ON, Canada: CSA.
CSA (Canadian Standards Association). 2019b. Limit states design of steel structures. Missisauga, ON, Canada: CSA.
Dassault Systèmes. 2016. Abaqus/CAE 2017. Johnston, RI: Dassault Systèmes Simulia Corp.
Dibley, J. E. 1969. “Lateral torsional buckling of I-sections in Grade 55 steel.” Proc. Inst. Civ. Eng. 43 (4): 599–627.
Dux, P. F., and S. Kitipornchai. 1983. “Inelastic beam buckling experiments.” J. Constr. Steel Res. 3 (1): 3–9. https://doi.org/10.1016/0143-974X(83)90011-1.
Fukumoto, Y., and Y. Itoh. 1981. “Statistical study of experiments on welded beams.” J. Struct. Div. 107 (1): 89–103. https://doi.org/10.1061/JSDEAG.0005639.
Fukumoto, Y., Y. Itoh, and M. Kubo. 1980. “Strength variation of laterally unsupported beams.” J. Struct. Div. 106 (1): 165–181. https://doi.org/10.1061/JSDEAG.0005334.
Fukumoto, Y., and M. Kubo. 1977. “An experimental review of lateral buckling of beams and girders.” In International colloquium on stability of structures under static and dynamic loads, 541–562. Reston, VA: ASCE.
Greiner, R., and P. Kaim. 2001. Comparison of LT-buckling design curves with test results, 1–23. Brussels, Belgium: European Convention for Constructional Steelwork.
Kabir, I., and A. K. Bhowmick. 2018. “Lateral torsional buckling of welded wide flange beams under constant moment.” Can. J. Civ. Eng. 45 (9): 766–779. https://doi.org/10.1139/cjce-2017-0499.
Kim, Y. D. 2010. “Behavior and design of metal building frames using general prismatic and web-tapered steel I-section members.” Doctoral dissertation, School of Civil and Environmental Engineering, Georgia Institute of Technology.
MacPhedran, I., and G. Y. Grondin. 2011. “A simple steel beam design curve.” Can. J. Civ. Eng. 38 (2): 141–153. https://doi.org/10.1139/L10-114.
Pekoz, T., R. Bjorhovde, S. J. Errera, B. G. Johnston, D. R. Sherman, and L. Tall. 1981. “Determination of residual stresses in structural shapes.” Exp. Mech. 5 (3): 4–7. https://doi.org/10.1111/j.1747-1567.1981.tb01604.x.
Powel, G., and J. Simons. 1981. “Improved iteration strategy for nonlinear structures.” Int. J. Numer. Methods Eng. 17 (10): 1455–1467. https://doi.org/10.1002/nme.1620171003.
Ramm, E. 1981. “Strategies for tracing the nonlinear response near limit points.” In Nonlinear finite element analysis in structural mechanics, 63–89. Berlin: Springer.
Slein, R., J. S. Bun, W. Latif, A. M. Kamath, A. A. Alshannaq, R. J. Sherman, D. W. Scott, and D. W. White. 2021. “Lateral-torsional buckling research needs and validation of an experimental setup in the elastic range.” Eng. J. 58 (4): 279–291.
Subramanian, L., and D. W. White. 2017. “Resolving the disconnects between lateral torsional buckling experimental tests, test simulations and design strength equations.” J. Constr. Steel Res. 128: 321–334. https://doi.org/10.1016/j.jcsr.2016.08.009.
Timoshenko, S. P., and J. M. Gere. 1961. Theory of elastic stability. New York: McGraw-Hill.
Unsworth, D., R. G. Driver, and L. Li. 2020. “Measurement and prediction of residual stresses in welded girders.” J. Constr. Steel Res. 169: 106007. https://doi.org/10.1016/j.jcsr.2020.106007.
Unsworth, D., R. G. Driver, L. Li, S. Twizell, and A. Imanpour. 2021. “Characterization of residual stresses for LTB simulations of modern welded girders.” J. Constr. Steel Res. 183: 106769. https://doi.org/10.1016/j.jcsr.2021.106769.
White, D. W., and S. K. Jung. 2008a. “Unified flexural resistance equations for stability design of steel I-section members—Uniform bending tests.” J. Struct. Eng. 134 (9): 1450–1470. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:9(1450).
White, D. W., and Y. D. Kim. 2008b. “Unified flexural resistance equations for stability design of steel I-section members—Moment gradient tests.” J. Struct. Eng. 134 (9): 1471–1486. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:9(1471).
Wong, E., R. G. Driver, and T. W. Heal. 2015. “Simplified approach to estimating the elastic lateral–torsional buckling capacity of steel beams with top-flange loading.” Can. J. Civ. Eng. 42 (2): 130–138. https://doi.org/10.1139/cjce-2014-0265.
Wong-Chung, A. D., and S. Kitipornchai. 1987. “Partially braced inelastic beam buckling experiments.” J. Constr. Steel Res. 7 (3): 189–211. https://doi.org/10.1016/0143-974X(87)90008-3.
Yarimci, E., J. A. Yura, and L. W. Lu. 1967. “Techniques for testing structures permitted to sway.” Exp. Mech. 7: 321–331. https://doi.org/10.1007/BF02326237.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Dec 5, 2021
Accepted: Apr 15, 2022
Published online: Jul 20, 2022
Published in print: Oct 1, 2022
Discussion open until: Dec 20, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Sheldon C. Twizell, Xiao Lin “Dimple” Ji, Ali Imanpour, Robert G. Driver, Lateral–Torsional and Distortional Buckling of I-Shaped Welded Steel Girders, Journal of Structural Engineering, 10.1061/JSENDH.STENG-11961, 149, 9, (2023).