A Mechanics-Based Finite Element for the Analysis of Shear-Critical Slender Reinforced Beams and Columns
Publication: Journal of Structural Engineering
Volume 148, Issue 9
Abstract
This paper presents the derivation and validation of a mechanics-based finite element for the analysis of shear-critical slender reinforced concrete beams and columns. The element can capture the load-deformation behavior associated with axial loads, bending moments, and shear in uncracked or cracked reinforced concrete using only a small number of degrees of freedom and easily measurable input parameters: the gross cross-section dimensions and steel and concrete material stress/strain curves. The element is specifically derived to represent the full reinforced concrete cross section (i.e., one element is required over the depth of a member) and consists of four nodes, with two translational degrees of freedom (DOFs) per node. This formulation facilitates modeling the interface regions between walls or joint regions, beams, or columns and lowers the numerical complexity and number of decisions that the user must make. The element shows improvements to results from design codes when validated against experimental results for 782 beams without shear reinforcement and 167 beams with shear reinforcement taken from the literature. By reducing the number of degrees of freedom, the element will allow relatively rapid two-dimensional (2D) nonlinear analyses of full reinforced concrete buildings.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors would like to acknowledge the support of the Natural Sciences and Engineering Research Council (NSERC) of Canada.
References
AASHTO. 2020. LRFD bridge design specifications and commentary. 9th ed. Washington, DC: AASHTO.
Acevedo, A. B., E. C. Bentz, and M. P. Collins. 2009. “Influence of clamping stresses in the shear strength of concrete slabs under uniform loads.” Supplement, J. Earthquake Eng. 13 (S1): 1–17. https://doi.org/10.1080/13632460902813190.
ACI (American Concrete Institute). 1963. Building code requirements for structural concrete. ACI 318-63. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2011. Building code requirements for structural concrete. ACI 318-11. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2019. Building code requirements for structural concrete. ACI 318-19. Farmington Hills, MI: ACI.
Adeghe, L. 1986. “A finite element model for studying reinforced concrete detailing problems.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Toronto.
Bathe, K.-J. 2014. Finite element procedures. 2nd ed. Englewood Cliffs, NJ: Prentice-Hall.
Bentz, E. C. 2000a. “Response-2000.” Accessed May 31, 2022. https://www.hadrianworks.com/.
Bentz, E. C. 2000b. “Sectional analysis of reinforced concrete members.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Toronto.
Bentz, E. C. 2005. “Explaining the riddle of tension stiffening models for shear panel experiments.” J. Struct. Eng. 131 (9): 1422–1425. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:9(1422).
Birely, A. C., L. N. Lowes, and D. E. Lehman. 2012. “Linear analysis of concrete frames considering joint flexibility.” ACI Struct. J. 109 (3): 381–392.
Bruun, E. P. G. 2017. “The hybrid panel-truss element: Developing a novel finite element for the nonlinear analysis of reinforced concrete beams and shells.” M.S. thesis, Dept. of Civil and Mineral Engineering, Univ. of Toronto. https://tspace.library.utoronto.ca/handle/1807/79117.
BSI (British Standard Institution). 2008. Design of concrete structures. Eurocode 2 (EC-2). London: BSI.
Collins, M. P., E. C. Bentz, P. T. Quach, and G. T. Proestos. 2015. “The challenge of predicting the shear strength of very thick slabs.” Concr. Int. 37 (11): 29–37.
Collins, M. P., and D. Mitchell. 1997. Prestressed concrete structures. Toronto: Response Publications.
Cross, H. 1930. “Analysis of continuous frames by distributing fixed-end moments.” Proc. Am. Soc. Civ. Eng. 96 (1): 1–10. https://doi.org/10.1061/TACEAT.0004333.
CSA (Canadian Standards Association). 2014. Design of concrete structures. CSA A23.3-14. Ottawa: CSA.
CSA (Canadian Standards Association). 2019. Design of concrete structures—Clause 11—Shear and torsion. CSA A23.3-14. Ottawa: CSA.
Jouravski, D. 1856. “Remarques sur la résistance d’un corps prismatique et d’une pièce composée en bois ou en tôle de fer a une force perpendiculaire à leur longueur.” Ann. Ponts Chaussées 12: 328–351.
Kaufmann, W., and P. Marti. 1998. “Structural concrete: Cracked membrane model.” J. Struct. Eng. 124 (12): 1467–1475. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:12(1467).
Maekawa, K., H. Okamura, and A. Pimanmas. 2003. Non-linear mechanics of reinforced concrete. London: CRC Press.
Mari, A., J. M. Bairam, A. Cladera, and E. Oller. 2016. “Shear design and assessment of reinforced and prestressed concrete beams based on a mechanical model.” J. Struct. Eng. 142 (10): 04016064. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001539.
Mitchell, D., and M. P. Collins. 1974. “Diagonal compression field theory—A rational model for structural concrete in pure torsion.” ACI J. 71 (8): 396–408. https://doi.org/10.14359/7103.
Reineck, K.-H., E. C. Bentz, B. Fitik, D. A. Kuchma, and O. Bayrak. 2013. “ACI-DAfStb database of shear tests on slender reinforced concrete beams without stirrups.” ACI Struct. J. 110 (5): 867–876. https://doi.org/10.14359/51685839.
Reineck, K.-H., E. C. Bentz, B. Fitik, D. A. Kuchma, and O. Bayrak. 2014. “ACI-DAfStb databases for shear tests on slender reinforced concrete beams with stirrups.” ACI Struct. J. 111 (5): 1147–1156. https://doi.org/10.14359/51686819.
Sherwood, E. G. 2008. “One-way shear behaviour of large, lightly-reinforced concrete beams and slabs.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Toronto.
Sherwood, E. G., E. C. Bentz, and M. P. Collins. 2007. “Effect of aggregate size on beam-shear strength of thick slabs.” ACI Struct. J. 104 (2): 180–190. https://doi.org/10.14359/18530.
Stevens, N. 1987. “Analytical modelling of reinforced concrete subjected to monotonic and reversed loadings.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Toronto.
Turneaure, F. E. 1908. Cyclopedia of Civil Engineering: A general reference work on surveying, railroad engineering, structural engineering, roofs and bridges, masonry and reinforced concrete, highway construction, hydraulic engineering, irrigation, river and harbor improvement, municipal engineering, cost analysis, etc. Chicago: American School of Correspondence.
Uzel, A. 2003. “Shear design of large footings.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Toronto.
Vecchio, F. J. 1989. “Nonlinear finite element analysis of reinforced concrete membranes.” ACI Struct. J. 86 (1): 26–35. https://doi.org/10.14359/2620.
Vecchio, F. J. 1990. “Reinforced concrete membrane element formulations.” J. Struct. Eng. 116 (3): 730–750. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:3(730).
Vecchio, F. J. 2001. “Non-linear finite element analysis of reinforced concrete: At the crossroads?” Struct. Concr. 2 (4): 201–212. https://doi.org/10.1680/stco.2001.2.4.201.
Vecchio, F. J., and M. P. Collins. 1986. “The modified compression-field theory for reinforced concrete elements subjected to shear.” ACI J. 83 (2): 219–231. https://doi.org/10.14359/10416.
Vecchio, F. J., D. Lai, W. Shim, and J. Ng. 2001. “Disturbed stress field model for reinforced concrete: Validation.” J. Struct. Eng. 127 (4): 350–358. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:4(350).
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Nov 16, 2021
Accepted: Apr 15, 2022
Published online: Jul 15, 2022
Published in print: Sep 1, 2022
Discussion open until: Dec 15, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.