Behavior and Design of Cold-Formed Steel Web-Stiffened Channels under Concentrated Bearing Loads
Publication: Journal of Structural Engineering
Volume 148, Issue 3
Abstract
This study focused on the web crippling and design of web-stiffened channel sections made of cold-formed steel (CFS). CFS web-stiffened channels are expected to have higher buckling loads under compression and bending compared to conventional channel sections without stiffened web. However, research on CFS web-stiffened channel sections under concentrated bearing loads is rather limited. A test program consisting of 29 web crippling experiments was carried out under the loading cases of interior-two-flange (ITF), end-two-flange (ETF), interior loading (IL), and end loading (EL). Both flanges of each channel section were bolted to the supports. The test results were used to establish and validate the finite-element models. Then, the validated numerical models were utilized for a parametric investigation to study the influences of cross-sectional geometry, bearing lengths, and web stiffener dimensions. A total of 576 finite-element analyses were performed in the parametric study. The web crippling design formulas for traditional CFS channels included in the current design standards were assessed by comparing the failure loads attained in the tests and numerical analyses to the predicted values. Finally, a design formula was developed for the design of CFS web-stiffened channels under concentrated bearing loads by modifying the codified web crippling unified equation.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The first author is grateful for the support given by the Research Grants Council of Hong Kong for the Hong Kong Ph.D. Fellowship Scheme.
References
ABAQUS. 2017. Abaqus version 2017 user’s manual. Vélizy-Villacoublay, France: Dassault Systèmes.
AISI (American Iron and Steel Institute). 2016a. Commentary on North American specification for the design of cold-formed steel structural members. Washington, DC: AISI.
AISI (American Iron and Steel Institute). 2016b. North American Specification for the design of cold-formed steel structural members. Washington, DC: AISI.
AISI (American Iron and Steel Institute). 2017. Test standard for determining the web crippling strength of cold-formed steel flexural members. Washington, DC: AISI.
Almatrafi, M., M. Theofanous, M. Bock, and S. Dirar. 2021. “Slenderness-based design for sigma sections subjected to interior one flange loading.” Thin-Walled Struct. 158 (Jan): 107194. https://doi.org/10.1016/j.tws.2020.107194.
AS/NZS (Australian/New Zealand Standard). 2018. Cold-formed steel structures. Sydney, NSW, Australia: Australian/New Zealand Standard.
ASTM. 2016. Standard test methods for tension testing of metallic materials. E8/E8M-16a. West Conshohocken, PA: ASTM.
Beshara, B. 1999. “Web crippling of cold-formed steel members.” M.A.Sc. thesis, Univ. of Waterloo.
CEN (European Committee for Standardization). 2006. Eurocode 3: Design of steel structures—Part 1-3: General rules-Supplementary rules for cold-formed members and sheeting. Brussels, Belgium: CEN.
Chen, M.-T., B. Young, A. D. Martins, D. Camotim, and P. B. Dinis. 2020. “Experimental investigation on cold-formed steel stiffened lipped channel columns undergoing local-distortional interaction.” Thin-Walled Struct. 150 (May): 106682. https://doi.org/10.1016/j.tws.2020.106682.
Degtyareva, N. V., and V. V. Degtyarev. 2016. “Experimental investigation of cold-formed steel channels with slotted webs in shear.” Thin-Walled Struct. 102 (May): 30–42. https://doi.org/10.1016/j.tws.2016.01.012.
Dinis, P. B., B. Young, and D. Camotim. 2014. “Strength, interactive failure and design of web-stiffened lipped channel columns exhibiting distortional buckling.” Thin-Walled Struct. 81 (Aug): 195–209. https://doi.org/10.1016/j.tws.2013.09.016.
Gatheeshgar, P., K. Poologanathan, S. Gunalan, K. D. Tsavdaridis, B. Nagaratnam, and E. Iacovidou. 2020. “Optimised cold-formed steel beams in modular building applications.” J. Build. Eng. 32 (Nov): 101607. https://doi.org/10.1016/j.jobe.2020.101607.
Haidarali, M. R., and D. A. Nethercot. 2012. “Local and distortional buckling of cold-formed steel beams with both edge and intermediate stiffeners in their compression flanges.” Thin-Walled Struct. 54 (May): 106–112. https://doi.org/10.1016/j.tws.2012.02.013.
Huang, X.-H., J. Yang, Q.-F. Liu, J. Zhu, L. Bai, F.-L. Wang, and J.-H. Wang. 2018. “A simplified flange–lip model for distortional buckling of cold-formed steel channel-sections with stiffened web.” Int. J. Mech. Sci. 136 (Feb): 451–459. https://doi.org/10.1016/j.ijmecsci.2017.12.034.
Huang, Y., and B. Young. 2014. “The art of coupon tests.” J. Constr. Steel Res. 96 (May): 159–175. https://doi.org/10.1016/j.jcsr.2014.01.010.
Kwon, Y. B., and G. J. Hancock. 1992. “Tests of cold-formed channels with local and distortional buckling.” J. Struct. Eng. 117 (7): 1786–1803. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:7(1786).
Laím, L., J. P. C. Rodrigues, and H. D. Craveiro. 2015. “Flexural behaviour of beams made of cold-formed steel sigma-shaped sections at ambient and fire conditions.” Thin-Walled Struct. 87 (Feb): 53–65. https://doi.org/10.1016/j.tws.2014.11.004.
Li, H.-T., and B. Young. 2019. “Behaviour of cold-formed high strength steel RHS under localised bearing forces.” Eng. Struct. 183 (Mar): 1049–1058. https://doi.org/10.1016/j.engstruct.2018.11.079.
Li, L.-Y. 2009. “Analyses of distortional buckling of cold-formed sigma purlins using EN1993-1-3.” J. Constr. Steel Res. 65 (12): 2099–2102. https://doi.org/10.1016/j.jcsr.2009.06.017.
Li, L.-Y., and J.-K. Chen. 2008. “An analytical model for analysing distortional buckling of cold-formed steel sections.” Thin-Walled Struct. 46 (12): 1430–1436. https://doi.org/10.1016/j.tws.2008.03.005.
Pham, C. H., and G. J. Hancock. 2015. “Numerical investigation of longitudinally stiffened web channels predominantly in shear.” Thin-Walled Struct. 86 (Jan): 47–55. https://doi.org/10.1016/j.tws.2014.09.005.
Pham, S. H., C. H. Pham, and G. J. Hancock. 2014. “Direct strength method of design for shear including sections with longitudinal web stiffeners.” Thin-Walled Struct. 81 (Aug): 19–28. https://doi.org/10.1016/j.tws.2013.09.002.
Schafer, B. W. 2011. “Cold-formed steel structures around the world.” Steel Constr. 4 (3): 141–149. https://doi.org/10.1002/stco.201110019.
Sundararajah, L., M. Mahendran, and P. Keerthan. 2017. “Web crippling studies of SupaCee sections under two flange load cases.” Eng. Struct. 153 (Dec): 582–597. https://doi.org/10.1016/j.engstruct.2017.09.058.
Sundararajah, L., M. Mahendran, and P. Keerthan. 2018. “Design of SupaCee sections subject to web crippling under one-flange load cases.” J. Struct. Eng. 144 (12): 04018222. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002206.
Wang, C., Z. Zhang, D. Zhao, and Q. Liu. 2016. “Compression tests and numerical analysis of web-stiffened channels with complex edge stiffeners.” J. Constr. Steel Res. 116 (Jan): 29–39. https://doi.org/10.1016/j.jcsr.2015.08.013.
Wang, L., and B. Young. 2014. “Design of cold-formed steel channels with stiffened webs subjected to bending.” Thin-Walled Struct. 85 (Dec): 81–92. https://doi.org/10.1016/j.tws.2014.08.002.
Ye, J., I. Hajirasouliha, J. Becque, and K. Pilakoutas. 2016. “Development of more efficient cold-formed steel channel sections in bending.” Thin-Walled Struct. 101 (Apr): 1–13. https://doi.org/10.1016/j.tws.2015.12.021.
Young, B., and G. J. Hancock. 2003. “Cold-formed steel channels subjected to concentrated bearing load.” J. Struct. Eng. 129 (8): 1003–1010. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:8(1003).
Zhao, X.-L., and G. J. Hancock. 1992. “Square and rectangular hollow sections subject to combined actions.” J. Struct. Eng. 118 (3): 648–667. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:3(648).
Zhao, X.-L., and G. J. Hancock. 1995. “Square and rectangular hollow sections under transverse end-bearing force.” J. Struct. Eng. 121 (9): 1323–1329. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:9(1323).
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 19, 2021
Accepted: Oct 6, 2021
Published online: Dec 23, 2021
Published in print: Mar 1, 2022
Discussion open until: May 23, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.