Design of Lean Duplex Stainless Steel Tubular Sections Subjected to Concentrated End-Bearing Loads
Publication: Journal of Structural Engineering
Volume 147, Issue 4
Abstract
This study presents the numerical investigation and design of cold-formed lean duplex stainless steel (CFLDSS) tubular sections subjected to concentrated end bearing loads, specifically end-one-flange (EOF), end-two-flange (ETF), and end loading (EL). Finite element models (FEM) were developed and verified against the test results of CFLDSS tubular sections subjected to the three loads. The FEM are able to predict the behavior of CFLDSS tubular sections in terms of ultimate strengths and web crippling failure. The verified FEM were used to perform an extensive parametric study that included a wide range of key parameters, including the ratios of flat web height to thickness, load bearing length to web thickness, and load bearing length to flat web height. Based on both the test and numerical results, new coefficients are proposed for the unified design equation and the direct strength method for the design of CFLDSS tubular sections subjected to the three concentrated end bearing loads. The strengths obtained from the tests and the parametric study were compared with the nominal strengths calculated using the design equations from current specifications and those in the literature, as well as those proposed in this study. Overall, the modified design rules provided more accurate predictions compared with the design rules in the current specifications and literature. The results showed that the proposed design methods are suitable for the web crippling design of CFLDSS tubular sections under the three concentrated end bearing loads.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
ABAQUS. 2019. Analysis user’s manual. Silicon Valley, CA: ABAQUS.
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. AISI S100-16. Washington, DC: American Iron and Steel Institute.
AS (Australian Standard). 1998. Steel structures. AS 4100. Sydney, Australia: Standards Australia.
ASCE. 2002. Specification for the design of cold-formed stainless steel structural members. SEI/ASCE 8-02. Reston, VA: ASCE.
AS/NZS (Australian/New Zealand Standard). 2001. Cold-formed stainless steel structures. AS/NZS 4673:2001. Sydney, Australia: Standards Australia.
Beshara, B., and P. M. Schuster. 2000. Web crippling data and calibrations of cold formed steel members. Waterloo, ON: Univ. of Waterloo.
Bock, M., I. Arrayago, E. Real, and E. Mirambell. 2013. “Study of web crippling in ferritic stainless steel cold formed sections.” Thin-Walled Struct. 69 (Aug): 29–44. https://doi.org/10.1016/j.tws.2013.03.015.
Cai, Y., and B. Young. 2014a. “Behavior of cold-formed stainless steel single shear bolted connections at elevated temperatures.” Thin-Walled Struct. 75 (Feb): 63–75. https://doi.org/10.1016/j.tws.2013.10.010.
Cai, Y., and B. Young. 2014b. “Structural behavior of cold-formed stainless steel bolted connections.” Thin-Walled Struct. 83 (Oct): 147–156. https://doi.org/10.1016/j.tws.2014.01.014.
Cai, Y., and B. Young. 2014c. “Transient state tests of cold-formed stainless steel single shear bolted connections.” Eng. Struct. 81 (Dec): 1–9. https://doi.org/10.1016/j.engstruct.2014.09.031.
Cai, Y., and B. Young. 2015. “High temperature tests of cold-formed stainless steel double shear bolted connections.” J. Constr. Steel Res. 104 (Jan): 49–63. https://doi.org/10.1016/j.jcsr.2014.09.015.
Cai, Y., and B. Young. 2019a. “Cold-formed lean duplex stainless steel tubular members under concentrated interior bearing loads.” J. Struct. Eng. 145 (7): 04019056. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002343.
Cai, Y., and B. Young. 2019b. “Web crippling of lean duplex stainless steel tubular sections under concentrated end bearing loads.” Thin-Walled Struct. 134 (Jan): 29–39. https://doi.org/10.1016/j.tws.2018.08.006.
CEN (European Committee for Standardization. 2015. Eurocode 3. Design of steel structures— Part 1–4: General rules—Supplementary rules for stainless steels. EN 1993-1-4:2006+A1:2015. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2005. Eurocode 0: Basis of structural design. EN 1990:2002+A1:2005. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2006. Eurocode 3: Design of steel structures—Part 1–3: General rules—Supplementary rules for cold-formed members and sheeting. EN 1993-1-3:2006. Brussels, Belgium: CEN.
dos Santos, G. B., and L. Gardner. 2019. “Testing and numerical analysis of stainless steel I-sections under concentrated end-one-flange loading.” J. Constr. Steel Res. 157 (Jun): 271–281. https://doi.org/10.1016/j.jcsr.2019.02.020.
dos Santos, G. B., L. Gardner, and M. Kucukler. 2018. “Experimental and numerical study of stainless steel I-sections under concentrated internal one-flange and internal two-flange loading.” Eng. Struct. 175 (Nov): 355–370. https://doi.org/10.1016/j.engstruct.2018.08.015.
Gardner, L., and N. R. Baddoo. 2006. “Fire testing and design of stainless steel structures.” J. Constr. Steel Res. 62 (6): 532–543. https://doi.org/10.1016/j.jcsr.2005.09.009.
Gardner, L., A. Talja, and N. R. Baddoo. 2006. “Structural design of high-strength austenitic stainless steel.” Thin-Walled Struct. 44 (5): 517–528. https://doi.org/10.1016/j.tws.2006.04.014.
Huang, Y., and B. Young. 2012. “Material properties of cold-formed lean duplex stainless steel sections.” Thin-Walled Struct. 54 (May): 72–81. https://doi.org/10.1016/j.tws.2012.02.003.
Huang, Y., and B. Young. 2013. “Tests of pin-ended cold-formed lean duplex stainless steel columns.” J. Constr. Steel Res. 82 (Mar): 203–215. https://doi.org/10.1016/j.jcsr.2013.01.001.
Huang, Y., and B. Young. 2014. “Experimental and numerical investigation of cold-formed lean duplex stainless steel flexural members.” Thin-Walled Struct. 73 (Dec): 216–228. https://doi.org/10.1016/j.tws.2013.07.019.
Keerthan, P., M. Mahendran, and E. Steau. 2014. “Experimental study of web crippling behaviour of hollow flange channel beams under two flange load cases.” Thin-Walled Struct. 85 (Dec): 207–219. https://doi.org/10.1016/j.tws.2014.08.011.
Li, H.-T., and B. Young. 2017. “Cold-formed ferritic stainless steel tubular structural members subjected to concentrated bearing loads.” Eng. Struct. 145 (Aug): 392–405. https://doi.org/10.1016/j.engstruct.2017.05.022.
Li, H.-T., and B. Young. 2018. “Web crippling of cold-formed ferritic stainless steel square and rectangular hollow sections.” Eng. Struct. 176 (Dec): 968–980. https://doi.org/10.1016/j.engstruct.2018.08.076.
Natário, P., N. Silvestre, and D. Camotim. 2016. “Direct strength prediction of web crippling failure of beams under ETF loading.” Thin-Walled Struct. 98 (Jan): 360–374. https://doi.org/10.1016/j.tws.2015.09.012.
Natário, P., N. Silvestre, and D. Camotim. 2017. “Web crippling of beams under ITF loading: A novel DSM-based design approach.” J. Constr. Steel Res. 128 (Jan): 812–824. https://doi.org/10.1016/j.jcsr.2016.10.011.
Prabakaran, K. 1993. Web crippling of cold formed steel sections. Waterloo, ON: Dept. of Civil Engineering, Univ. of Waterloo.
Prabakaran, K., and P. M. Schuster. 1998. “Web crippling of cold formed steel members.” In Proc., 14th Int. Specialty Conf. on Cold Formed Steel Structures, 151–164. Rolla, MO: Univ. of Missouri.
Saliba, N., and L. Gardner. 2013a. “Cross-section stability of lean duplex stainless steel welded I-sections.” J. Constr. Steel Res. 80 (Jan): 1–14. https://doi.org/10.1016/j.jcsr.2012.09.007.
Saliba, N., and L. Gardner. 2013b. “Experimental study of the shear response of lean duplex stainless steel plate girders.” Eng. Struct. 46 (Jan): 375–391. https://doi.org/10.1016/j.engstruct.2012.07.029.
Saliba, N., E. Real, and L. Gardner. 2014. “Shear design recommendations for stainless steel plate girders.” Eng. Struct. 59 (Feb): 220–228. https://doi.org/10.1016/j.engstruct.2013.10.016.
Theofanous, M., and L. Gardner. 2009. “Testing and numerical modelling of lean duplex stainless steel hollow section columns.” Eng. Struct. 31 (12): 3047–3058. https://doi.org/10.1016/j.engstruct.2009.08.004.
Theofanous, M., and L. Gardner. 2010. “Experimental and numerical studies of lean duplex stainless steel beams.” J. Constr. Steel Res. 66 (6): 816–825. https://doi.org/10.1016/j.jcsr.2010.01.012.
Wang, F., B. Young, and L. Gardner. 2019. “Experimental study of square and rectangular CFDST sections with stainless steel outer tubes under axial compression.” J. Struct. Eng. 145 (11): 04019139. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002408.
Xing, B., and B. Young. 2017. “Experimental investigation of concrete-filled lean duplex stainless steel RHS stub columns.” In Proc., 16th Int. Symp. on Tubular Structures (ISTS16), edited by A. Heidarpour and X.-L. Zhao, 95–100. Boca Raton, FL: CRC Press.
Young, B., and G. J. Hancock. 2001. “Design of cold-formed channels subjected to web crippling.” J. Struct. Eng. 127 (10): 1137–1144. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:10(1137).
Zhao, O., S. Afshan, and L. Gardner. 2017. “Structural response and continuous strength method design of slender stainless steel cross-sections.” Eng. Struct. 140 (Jun): 14–25. https://doi.org/10.1016/j.engstruct.2017.02.044.
Zhao, O., and L. Gardner. 2018. “The continuous strength method for the design of mono-symmetric and asymmetric stainless steel cross-sections in bending.” J. Constr. Steel Res. 150 (Nov): 141–152. https://doi.org/10.1016/j.jcsr.2018.08.001.
Zhao, O., B. Rossi, L. Gardner, and B. Young. 2015a. “Behaviour of structural stainless steel cross-sections under combined loading—Part I: Experimental study.” Eng. Struct. 89 (Apr): 236–246. https://doi.org/10.1016/j.engstruct.2014.11.014.
Zhao, O., B. Rossi, L. Gardner, and B. Young. 2015b. “Behaviour of structural stainless steel cross-sections under combined loading—Part II: Numerical modelling and design.” Eng. Struct. 89 (Apr): 247–259. https://doi.org/10.1016/j.engstruct.2014.11.016.
Zhou, F., and B. Young. 2006. “Cold-formed stainless steel sections subjected to web crippling.” J. Struct. Eng. 132 (1): 134–144. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:1(134).
Zhou, F., and B. Young. 2007a. “Cold-formed high-strength stainless steel tubular sections subjected to web crippling.” J. Struct. Eng. 133 (3): 368–377. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:3(368).
Zhou, F., and B. Young. 2007b. “Experimental and numerical investigations of cold-formed stainless steel tubular sections subjected to concentrated bearing load.” J. Constr. Steel Res. 63 (11): 1452–1466. https://doi.org/10.1016/j.jcsr.2006.12.007.
Zhou, F., and B. Young. 2008. “Web crippling of cold-formed stainless steel tubular sections.” Adv. Struct. Eng. 11 (6): 679–691. https://doi.org/10.1260/136943308787543658.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Apr 13, 2020
Accepted: Oct 16, 2020
Published online: Jan 20, 2021
Published in print: Apr 1, 2021
Discussion open until: Jun 20, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.