Rate-Dependent Behavior of Transverse Welded Lap Joints at Elevated Temperatures
Publication: Journal of Structural Engineering
Volume 147, Issue 2
Abstract
This paper presents key findings of an experimental program performed to examine the rate-dependent behavior of weld material in transverse welded lap joints at elevated temperatures under steady-state thermal conditions. The data are intended to support the development of models of welded connections for structural-fire engineering applications. Two different loading rate scenarios (fast and slow) were incorporated in the experiments to evaluate the loading rate effect on the strength and deformation capacity of welded connection test specimens at ambient and elevated temperatures. Retention factors for the weld material under both slow and fast loading rates were computed and compared with those available in the literature. Results from this study indicate that the loading rate has a significant effect on the strength and deformation capacities of transverse welded lap joints for temperatures greater than 450°C.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors gratefully acknowledge the financial support provided by the American University of Beirut Research Board under Grant No. 103604-24705. The authors further would like to thank the University of Texas at Austin for giving the authors permission to perform the experimental part of this study at the Ferguson Structural Engineering Laboratory.
References
AISC. 2016. Specification for structural steel buildings. ANSI/AISC 360. Chicago: AISC.
ASCE. 1992. Structural fire protection: ASCE committee on fire protection, manual no. 78. Reston, VA: ASCE.
ASTM. 2014. Standard specification for high-strength carbon-manganese steel of structural quality. ASTM A529/A529M. West Conshohocken, PA: ASTM.
AWS (American Welding Society). 2012. Specification for carbon steel electrodes for shielded metal arc welding. AWS A5.1/A5.1M. Doral, FL: AWS.
CEN (European Committee for Standardization). 2005. Design of steel structures—Part 1-2: General rules-structural fire design. EN 1993-1-2. Eurocode 3. Brussels, Belgium: CEN.
Conlon, K. 2009. “Strength of transverse fillet welds at elevated and post-elevated temperatures.” M.Sc. dissertation, Dept. of Civil and Environmental Engineering, Lehigh Univ.
Cooke, G. M. E. 1988. “An introduction to the mechanical properties of structural steel at elevated temperatures.” Fire Saf. J. 13 (1): 45–54. https://doi.org/10.1016/0379-7112(88)90032-X.
Hanus, F., G. Zilli, and J.-M. Franssen. 2011. “Experimental tests and analytical models for welds and grade 8.8 bolts under heating and subsequent cooling.” J. Struct. Fire Eng. 2 (3): 181–194. https://doi.org/10.1260/2040-2317.2.3.181.
Hu, G., M. A. Morovat, J. Lee, E. Schell, and M. Engelhardt. 2009. “Elevated temperature properties of ASTM A992 steel.” In Proc., 2009 Structures Congress, 1067–1076. Reston, VA: ASCE.
Kirby, B. R., and R. R. Preston. 1988. “High temperature properties of hot-rolled structural steels for use in fire engineering design studies.” Fire Saf. J. 13 (1): 27–37. https://doi.org/10.1016/0379-7112(88)90030-6.
Kodur, V. K. R., and M. M. S. Dwaikat. 2010. “Effect of high temperature creep on the fire response of restrained steel beams.” Mater. Struct. 43 (10): 1327–1341. https://doi.org/10.1617/s11527-010-9583-y.
Latham, D. J., and B. R. Kirby. 1998. Elevated temperature behavior of welded joints in structural steels. Amsterdam, Netherlands: Elsevier.
Luecke, W. E., J. D. McColskey, C. N. McCowan, S. W. Banovic, R. J. Fields, T. Foecke, T. A. Siewert, and F. W. Gayle. 2005. Federal building and fire safety investigation of the world trade center disaster: Mechanical properties of structural steel.. Gaithersburg, MD: National Institute of Standards and Technology.
Seif, M., L. Choe, J. Gross, W. Luecke, J. Main, D. McColskey, F. Sadek, J. Weigand, and C. Zhang. 2016. Temperature-dependent material modeling for structural steels: Formulation and application.. Gaithersburg, MD: National Institute of Standards and Technology.
Torić, N., A. Harapin, I. Boko, B. Peroš, and M. Ban. 2013. “Modelling of the influence of creep strains on the fire response of steel elements.” In Proc., Int. Conf. on Application of Structural Fire Engineering, 480–485. Prague, Czech Republic: Czech Technical Univ.
Torić, N., R. R. Sun, and I. W. Burgess. 2016. “Creep-free fire analysis of steel structures with Eurocode 3 material model.” J. Struct. Fire. Eng. 7 (3): 234–248. https://doi.org/10.1108/JSFE-09-2016-016.
Twilt, L. 2001. “The new Eurocode on fire design of steel structures.” In Proc., Int. Seminar on Steel Structures in Fire. Shanghai, China: Tongji Univ.
Ufuah, E., and J. Ikhayere. 2013. “Elevated temperature mechanical properties of butt-welded connections made with high strength steel grades S355 and S460M.” In Design, fabrication and economy of metal structures, 407–412. Cham, Switzerland: Springer.
Zhang, G., M.-C. Zhu, V. Kodur, and G.-Q. Li. 2017. “Behavior of welded connections after exposure to elevated temperature.” J. Constr. Steel Res. 130 (Mar): 88–95. https://doi.org/10.1016/j.jcsr.2016.12.004.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jul 18, 2019
Accepted: Aug 28, 2020
Published online: Nov 20, 2020
Published in print: Feb 1, 2021
Discussion open until: Apr 20, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.