Investigation of Failure Behavior in the Thread Contact of Wood Screws during the Pull-Out Process
Publication: Journal of Structural Engineering
Volume 146, Issue 10
Abstract
For optimizing wood screws, it is necessary to understand the failure behavior as well as the effect of screw parameters in the thread contact on the withdrawal capacity. The aim of this paper is to investigate the failure behavior of self-tapping wood screws in spruce wood [picea abies (L.)] during the pull-out process. Because this is possible with existing methods to a certain extent only, two analysis techniques used for investigations of chemical anchoring are adapted. The experiments are carried out using five self-tapping wood screws with an outer diameter of 6 mm. The results show that the screw movement observed during the pull-out process is much smaller than the displacement measured by pull-out machines for certification purposes. Another observation is that the failure behavior of different screw types varies with regard to crack formation. Improved understanding of failure behavior will allow for an in-depth investigation of the influence of screw parameters and, hence, for the design of improved wood screws.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors would like to thank the company Adolf Würth GmbH & Co. KG for the joint work in this research project. This research was supported by the Research Center for Steel, Timber, and Masonry, Karlsruhe Institute of Technology (KIT).
References
Aimene, Y. E., and J. A. Nairn. 2015. “Simulation of transverse wood compression using a large-deformation, hyperelastic–plastic material model.” Wood Sci. Technol. 49 (1): 21–39. https://doi.org/10.1007/s00226-014-0676-6.
Appl, J.-J. 2009. “Tragverhalten von Verbunddübeln unter Zugbelastung.” Ph.D. dissertation, Institute of Construction Materials, Universität Stuttgart.
Ballerini, M. 2012. “Experimental investigation on parallel-to-grain wood-to-wood joints with self-tapping screws.” In Proc., World Conf. on Timber Engineering, 173–182. Red Hook, NY: Curran Associates, Inc.
Blaß, H. J., I. Bejtka, and T. Uibel. 2006. Tragfähigkeit von Verbindungen mit selbstbohrenden Holzschrauben mit Vollgewinde. Karlsruhe, Germany: Universitätsverlag Karlsruhe.
Blaß, H. J., and T. Uibel. 2009. Spaltversagen von Holz in Verbindungen: Ein Rechenmodell für die Rissbildung beim Eindrehen von Holzschrauben. Karlsruhe, Germany: Universitätsverlag Karlsruhe.
Bodner, J., M. G. Schlag, and G. Grüll. 1997. “Fracture initiation and progress in wood specimens stressed in tension. I: Clear wood specimens stressed parallel to the grain.” Holzforschung 51 (5): 479–484. https://doi.org/10.1515/hfsg.1997.51.5.479.
Booker, R. E., and J. Sell. 1998. “The nanostructure of the cell wall of softwoods and its functions in a living tree.” Eur. J. Wood Wood Prod. 56 (1): 1–8. https://doi.org/10.1007/s001070050255.
Brown, D. 2017. “Tracker: Video analysis and modeling tool.” Accessed February 22, 2017. http://physlets.org/tracker/.
DIN (Deutsches Institut für Normung). 1991. Timber structures: Joints made with mechanical fasteners. DIN EN 26891:1991-07. Berlin: DIN.
DIN (Deutsches Institut für Normung). 2002. Wood-based panels: Determination of withdrawal capacity of fasteners. DIN EN 13446:2002-09. Berlin: DIN.
DIN (Deutsches Institut für Normung). 2016. Timber structures: Test methods—Withdrawal capacity of timber fasteners. DIN EN 1382:2016-07. Berlin: DIN.
Dylla, N., and G. Fricke. 1995. “Erfolgreich entwickeln.” VDI Berichte 1169 (1): 117–123.
Echavarría, C. 2007. “Bolted timber joints with self-tapping screws.” Revista EIA 8: 37–47.
EOTA (European Organisation for Technical Assessment). 2016. Screws for use in timber constructions. EAD 130118-00-0603. Brussels, Belgium: EOTA.
Franke, B., and P. Quenneville. 2011. “Numerical modeling of the failure behavior of dowel connections in wood.” J. Eng. Mech. 137 (3): 186–195. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000217.
Frese, M., P. Fellmoser, and H. J. Blaß. 2010. “Models for the calculation of the withdrawal capacity of self-tapping screws.” Eur. J. Wood Wood Prod. 68 (4): 373–384. https://doi.org/10.1007/s00107-009-0378-1.
Holstein, A. J., and D. R. Bohnhoff. 2013. “Bending properties of wood I-sections fabricated with screws and polyurethane adhesive.” J. Struct. Eng. 139 (11): 2019–2027. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000772.
Horn, S., K. Hoelz, M. Schwabe, and S. Matthiesen. 2019. “Experimental investigation of failure processes on chemical anchors with an in situ-test model.” Beton-Stahlbetonbau 99 (7): 561. https://doi.org/10.1002/best.201900013.
Jensen, J. L., M. Nakatani, P. Quenneville, and B. Walford. 2011. “A simple unified model for withdrawal of lag screws and glued-in rods.” Eur. J. Wood Wood Prod. 69 (4): 537–544. https://doi.org/10.1007/s00107-010-0478-y.
Lindemann, U. 2016. Handbuch Produktentwicklung. München, Germany: Hanser.
Matthiesen, S., P. Grauberger, T. Nelius, and K. Hölz. 2017a. Methodische Unterstützung des Erkenntnisgewinns in der Produktentwicklung durch Konstruktionshypothesen. Karlsruhe, Germany: Institute for Product Development Karlsruhe.
Matthiesen, S., K. Hoelz, and P. Grauberger. 2017b. “Systemverständnis durch Analysemethoden.” In Proc., Symp. Design for X. Hamburg, Germany: TUTECH Innovation.
Pirnbacher, G., R. Brandner, and G. Schickhofer. 2009. “Base parameters of self-tapping screws.” In Proc., CIB-W18, 123–139. Karlsruhe, Germany: Lehrstuhl für Ingenieurholzbau und Baukonstruktionen, Univ. of Karlsruhe.
Pirnbacher, G., and G. Schickhofer. 2007. “Schrauben im Vergleich–eine empirische Betrachtung.” In Proc., Grazer Holzbau-Fachtagung, F-1–F-22. Graz, Austria: Institut für Holzbau und Holztechnologie, Technische Universität Graz.
Pirnbacher, G., and G. Schickhofer. 2010. “Load bearing- and optimization potential of self-tapping wood screws.” In Proc., World Conf. on Timber Engineering, 147–155. Red Hook, NY: Curran Associates, Inc.
Policińska-Serwa, A., P. Kozakiewicz, and S. Krzosek. 2016. “Compression strength parallel to grain of structural ekki wood.” Warsaw Univ. Life Sci. 93: 122–127.
Ringhofer, A., R. Brandner, G. Flatscher, and G. Schickhofer. 2015a. “Axially loaded screws in solid timber, glued laminated timber and cross laminated timber.” Bautechnik 92 (11): 770–782. https://doi.org/10.1002/bate.201500075.
Ringhofer, A., R. Brandner, and G. Schickhofer. 2015b. “Withdrawal resistance of self-tapping screws in unidirectional and orthogonal layered timber products.” Mater. Struct. 48 (5): 1435–1447. https://doi.org/10.1617/s11527-013-0244-9.
Ruckpaul, A., A. Kriltz, and S. Matthiesen. 2014. “Using eye tracking to understand the engineering designers’ behavior in synthesis-driven analyzing processes: Experiences in study design.” In Proc., Int. Conf. on Human Behavior in Design. Zurich, Switzerland: ETH Zurich.
Shao, Z., and F. Wang. 2018. The fracture mechanics of plant materials: Wood and bamboo. Singapore: Springer.
Song, X., Y. Jiang, X. Gu, and Y. Wu. 2017. “Load-carrying capacity of lengthwise cracked wood beams retrofitted by self-tapping screws.” J. Struct. Eng. 143 (6): 04017021. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001742.
Sydor, M. 2019. “Geometry of wood screws: A patent review.” Eur. J. Wood Wood Prod. 77 (1): 93–103. https://doi.org/10.1007/s00107-018-1362-4.
Zarnani, P., and P. Quenneville. 2014. “Strength of timber connections under potential failure modes: An improved design procedure.” Constr. Build. Mater. 60 (Jun): 81–90. https://doi.org/10.1016/j.conbuildmat.2014.02.049.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Oct 27, 2019
Accepted: Apr 20, 2020
Published online: Jul 27, 2020
Published in print: Oct 1, 2020
Discussion open until: Dec 27, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.