Experimental Investigation of Self-Centering Beams for Moment-Resisting Frames
Publication: Journal of Structural Engineering
Volume 146, Issue 3
Abstract
Previously proposed self-centering moment-resisting frames relied on gap opening and closing in the beam–column interface to achieve recentering capability and energy dissipation capacity. The gap-opening mechanism in the connection interface induces deformation incompatibility with floor slabs and can require complex field construction. To address these drawbacks, a new type of self-centering beam (SCB) has recently been developed. The SCB uses high strength posttensioning (PT) strands inside the beam unit to provide recentering capacity and pretensioned bolt frictional devices to dissipate seismic energy. First, the mechanism of this new beam subassembly is explained and the equations governing the global behavior are given. Eleven approximately half-scale tests were conducted to isolate and investigate the effects of design parameters such as initial stress in the PT strands, and slip resistance in the friction device on system strength and stiffness when subjected to quasistatic cyclic loading. After cyclic displacements up to drift levels of 3%, all specimens experienced nearly zero residual drift, and no yielding was identified in the any of the structural members.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research described in this paper was sponsored by the National Natural Science Foundation of China (51208095); Qing Lan Project of Jiangsu Province; Fundamental Research Funds for the Central Universities (KYLX15_0080); Postgraduate Research & Practice Innovation Program of Jiangsu Province (KYCX17_0119); and a project funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD). The supporters are gratefully acknowledged.
References
AISC. 2016a. Prequalified connections for special and intermediate steel moment frames for seismic applications. ANSI/AISC 358. Chicago: AISC.
AISC. 2016b. Specification for structural steel buildings. ANSI/AISC 360. Chicago: AISC.
Chou, C. C., and J. H. Chen. 2011a. “Development of floor slab for steel post-tensioned self-centering moment frames.” J. Constr. Steel Res. 67 (10): 1621–1635. https://doi.org/10.1016/j.jcsr.2011.04.006.
Chou, C. C., and J. H. Chen. 2011b. “Seismic design and shake table tests of a steel post-tensioned self-centering moment frame with a slab accommodating frame expansion.” Earthquake Eng. Struct. Dyn. 40 (11): 1241–1261. https://doi.org/10.1002/eqe.1086.
Chou, C. C., K. C. Tsai, and W. C. Yang. 2009. “Self-centering steel connections with steel bars and a discontinuous composite slab.” Earthquake Eng. Struct. Dyn. 38 (4): 403–422. https://doi.org/10.1002/eqe.856.
Christopoulos, C., A. Filiatrault, C. M. Uang, and B. Folz. 2002. “Posttensioned energy dissipating connections for moment-resisting steel frames.” J. Struct. Eng. 128 (9): 1111–1120. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:9(1111).
Christopoulos, C., R. Tremblay, H.-J. Kim, and M. Lacerte. 2008. “Self-centering energy dissipative bracing system for the seismic resistance of structures: Development and validation.” J. Struct. Eng. 134 (1): 96–107. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:1(96).
Clayton, P. M., T. B. Winkley, J. W. Berman, and L. N. Lowes. 2012. “Experimental investigation of self-centering steel plate shear walls.” J. Struct. Eng. 138 (7): 952–960. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000531.
Clifton, G. C. 2005. “Semi-rigid joints for moment-resisting steel framed seismic-resisting systems.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Univ. of Auckland.
Darling S. C., M. R. Eatherton, and A. Maurya. 2013 “Self-centering beams for seismically resilient moment frames.” In Proc., Structures Congress, 1701–1712. Reston, VA: ASCE.
Dowden D. M., and M. Bruneau. 2014. Analytical and experimental investigation of self-centering steel plate shear walls. Buffalo, NY: State Univ. of New York.
Dowden, D. M., and M. Bruneau. 2016. “Dynamic shake-table testing and analytical investigation of self-centering steel plate shear walls.” J. Struct. Eng. 142 (10): 04016082. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001547.
Dowden, D. M., P. M. Clayton, C.-H. Li, J. W. Berman, M. Bruneau, L. N. Lowes, and K.-C. Tsai. 2016. “Full-scale pseudodynamic testing of self-centering steel plate shear walls.” J. Struct. Eng. 142 (1): 04015100. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001367.
Eguchi, R. T., J. D. Goltz, C. E. Taylor, S. E. Chang, P. J. Flores, L. A. Johnson, and N. C. Blais. 1998. “Direct economic losses in the Northridge earthquake: A three-year post-event perspective.” Earthquake Spectra 14 (2): 245–264. https://doi.org/10.1193/1.1585998.
Erochko, J., C. Christopoulos, and R. Tremblay. 2015. “Design, testing, and detailed component modeling of a high-capacity self-centering energy-dissipative brace.” J. Struct. Eng. 141 (8): 04014193. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001166.
Garlock, M. M., J. M. Ricles, and R. Sause. 2005. “Experimental studies of full-scale posttensioned steel connections.” J. Struct. Eng. 131 (3): 438–448. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:3(438).
Grigorian, C. E., T. S. Yang, and E. P. Popov. 1993. “Slotted bolted connection energy dissipators.” Earthquake Spectra 9 (3): 491–504. https://doi.org/10.1193/1.1585726.
Huang, X., Z. Zhou, K. Hua, C. Guo, D. Zhu, and T. Xia. 2018. “Influence of infill configurations on seismic responses of steel self-centering moment resisting frames.” Struct. Des. Tall Special Build. 27 (10): e1474. https://doi.org/10.1002/tal.1474.
Huang, X., Z. Zhou, Q. Xie, R. Xue, and D. Zhu. 2017. “Force distribution analysis of self-centering coupled-beams for moment-resisting-frames without floor elongation.” Eng. Struct. 147 (Sep): 328–344. https://doi.org/10.1016/j.engstruct.2017.05.055.
Khoo, H. H., C. Clifton, J. Butterworth, and G. MacRae. 2013. “Experimental study of full-scale self-centering sliding hinge joint connections with friction ring springs.” J. Earthquake Eng. 17 (7): 972–997. https://doi.org/10.1080/13632469.2013.787378.
Khoo, H. H., C. Clifton, J. Butterworth, G. MacRae, and G. Ferguson. 2012a. “Influence of steel shim hardness on the Sliding Hinge Joint performance.” J. Constr. Steel Res. 72 (May): 119–129. https://doi.org/10.1016/j.jcsr.2011.11.009.
Khoo, H. H., C. Clifton, J. Butterworth, G. MacRae, S. Gledhill, and G. Sidwell. 2012b. “Development of the self-centering sliding Hinge Joint with friction ring springs.” J. Constr. Steel Res. 78 (Nov): 201–211. https://doi.org/10.1016/j.jcsr.2012.07.006.
Kim, H.-J., and C. Christopoulos. 2008. “Friction damped posttensioned self-centering steel moment-resisting frames.” J. Struct. Eng. 134 (11): 1768–1779. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:11(1768).
Lin, Y.-C. 2014. “Behavior of a steel coupled beam moment frame based on nonlinear analyses.” J. Constr. Steel Res. 99 (Aug): 10–17. https://doi.org/10.1016/j.jcsr.2014.02.008.
Lin, Y.-C. 2015a. “Steel sliding-controlled coupled beam modules: Development and seismic behavior for a moment resisting frame.” Eng. Struct. 99 (Sep): 726–736. https://doi.org/10.1016/j.engstruct.2015.05.008.
Lin, Y.-C. 2015b. “Steel sliding-controlled coupled beam modules for advanced resilience of moment resisting frame building systems.” In Proc., Structures Congress, 1423–1434. Reston, VA: ASCE.
Lin, Y.-C., R. Sause, and J. Ricles. 2013. “Seismic performance of a large-scale steel self-centering moment-resisting frame: MCE hybrid simulations and quasi-static pushover tests.” J. Struct. Eng. 139 (7): 1227–1236. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000661.
Maurya, A., and M. R. Eatherton. 2015. “Large-scale experimental results for SC beams with resilient seismic performance.” In Proc., Structures Congress, 1326–1337. Reston, VA: ASCE.
Maurya, A., and M. R. Eatherton. 2016. “Experimental study of the restoring force mechanism in the self-centering beam (SCB).” Front. Struct. Civ. Eng. 10 (3): 272–282. https://doi.org/10.1007/s11709-016-0346-x.
Maurya, A., M. R. Eatherton, R. Matsui, and S. H. Florig. 2016. “Experimental investigation of miniature buckling restrained braces for use as structural fuses.” J. Constr. Steel Res. 127 (Dec): 54–65. https://doi.org/10.1016/j.jcsr.2016.07.019.
Moradi, S., and M. S. Alam. 2017. “Lateral load–drift response and limit states of posttensioned steel beam-column connections: Parametric study.” J. Struct. Eng. 143 (7): 04017044. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001772.
Može, P., and D. Beg. 2014. “A complete study of bearing stress in single bolt connections.” J. Constr. Steel Res. 95 (Apr): 126–140.
Parker, M., and D. Steenkamp. 2012. “The economic impact of the Canterbury earthquakes.” Reserve Bank New Zealand Bull. 75 (3): 13–25.
Rex, C. O., and W. S. Easterling. 2003. “Behavior and modeling of a bolt bearing on a single plate.” J. Struct. Eng. 129 (6): 792–800. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:6(792).
Ricles, J. M., R. Sause, S. W. Peng, and L. W. Lu. 2002. “Experimental evaluation of earthquake resistant posttensioned steel connections.” J. Struct. Eng. 128 (7): 850–859. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:7(850).
Song, L., T. Guo, and C. Chen. 2014. “Experimental and numerical study of a self-centering prestressed concrete moment resisting frame connection with bolted web friction devices.” Earthquake Eng. Struct. Dyn. 43 (4): 529–545. https://doi.org/10.1002/eqe.2358.
Vasdravellis, G., T. L. Karavasilis, and B. Uy. 2013. “Large-scale experimental validation of steel posttensioned connections with web hourglass pins.” J. Struct. Eng. 139 (6): 1033–1042. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000696.
Wang, W., X. Du, Y. Zhang, and Y. Chen. 2017. “Experimental investigation of beam-through steel frames with self-centering modular panels.” J. Struct. Eng. 143 (5): 04017006. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001743.
Wang, W., J. Kong, Y. Zhang, G. Chu, and Y. Chen. 2018. “Seismic behavior of self-centering modular panel with slit steel plate shear walls: Experimental testing.” J. Struct. Eng. 144 (1): 04017179. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001932.
Xie, Q., Z. Zhou, J. H. Huang, and S. P. Meng. 2016. “Influence of tube length tolerance on seismic responses of multi-storey buildings with dual-tube self-centering buckling-restrained braces.” Eng. Struct. 116 (Jun): 26–39. https://doi.org/10.1016/j.engstruct.2016.02.023.
Zhang, A., Y. Zhang, R. Li, and Z. Y. Wang. 2016. “Cyclic behavior of a prefabricated self-centering beam–column connection with a bolted web friction device.” Eng. Struct. 111 (Mar): 185–198. https://doi.org/10.1016/j.engstruct.2015.12.025.
Zhao, B., F. Taucer, and T. Rossetto. 2009. “Field investigation on the performance of building structures during the 12 May 2008 Wenchuan earthquake in China.” Eng. Struct. 31 (8): 1707–1723. https://doi.org/10.1016/j.engstruct.2009.02.039.
Zhou, Z., Q. Xie, X. C. Lei, X. T. He, and S. P. Meng. 2015. “Experimental investigation of the hysteretic performance of dual-tube self-centering buckling-restrained braces with composite tendons.” J. Compos. Constr. 19 (6): 04015011. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000565.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jul 23, 2018
Accepted: Jul 17, 2019
Published online: Dec 20, 2019
Published in print: Mar 1, 2020
Discussion open until: May 20, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.