Analytical Calculation Model for Predicting Cracking Behavior of Reinforced Concrete Ties
Publication: Journal of Structural Engineering
Volume 146, Issue 2
Abstract
This paper formulates an analytical calculation model for predicting the cracking behavior of reinforced concrete ties to provide more consistent crack width calculation methods for large-scale concrete structures in which large bar diameters and covers are used. The calculation model was derived based on the physical behavior of reinforced concrete ties reported from experiments and finite-element analyses in the literature. The derivations led to a second order differential equation for the slip that accounts for the three-dimensional effects of internal cracking by using a proper bond-slip law. The second order differential equation for the slip was solved completely analytically, resulting in a closed-form solution in the case of lightly loaded members and in a non-closed-form solution in the case of heavily loaded members. Finally, the paper provides a solution strategy to facilitate a practical and applicable method for predicting the complete cracking response. Comparison with experimental and finite-element results in the literature demonstrated the ability of the calculation model to predict crack widths and crack spacing consistently and on the conservative side regardless of the bar diameter and cover.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The work presented in this paper is part of an ongoing Ph.D. study funded by the Norwegian Public Roads Administration as a part of the Coastal Highway Route E39 project.
References
Balázs, G. L. 1993. “Cracking analysis based on slip and bond stresses.” ACI Mater. J. 90 (4): 340–348.
Beeby, A. W. 2004. “The influence of the parameter on crack widths.” J. Struct. Concr. 5 (2): 71–83. https://doi.org/10.1680/stco.2004.5.2.71.
Borosnyói, A., and I. Snóbli. 2010. “Crack width variation within the concrete cover of reinforced concrete members.” Építőanyag 62 (3): 70–74. https://doi.org/10.14382/epitoanyag-jsbcm.2010.14.
Borosnyói, B., and G. L. Balázs. 2005. “Models for flexural cracking in concrete: The state of the art.” J. Struct. Concr. 6 (2): 53–62. https://doi.org/10.1680/stco.2005.6.2.53.
Braam, C. R. 1990. “Control of crack width in deep reinforced concrete beams.” Ph.D. thesis, Faculty of Civil Engineering, Delft Univ. of Technology.
Bresler, B., and V. V. Bertero. 1968. “Behavior of reinforced concrete under repeated load.” J. Struct. Div. 94 (6): 1567–1590.
Broms, B. 1968. “Theory of the calculation of crack width and crack spacing in reinforced concrete members.” [In Swedish.] Cem. Betong 1: 52–64.
Caldentey, A. P., H. C. Peiretti, J. P. Iribarren, and A. G. Soto. 2013. “Cracking of RC members revisited: Influence of cover, ϕ/ρs,ef and stirrup spacing: An experimental and theoretical study.” J. Struct. Concr. 14 (1): 69–78. https://doi.org/10.1002/suco.201200016.
CEN (European Committee for Standardization). 2004. Eurocode 2: Design of concrete structures: Part 1-1: General rules and rules for buildings. EN 1992-1-1. Brussels, Belgium: CEN.
CEOS.fr. 2016. Control of cracking in reinforced concrete structures. London: ISTE.
Debernardi, P. G., and M. Taliano. 2016. “An improvement to Eurocode 2 and fib model code 2010 methods for calculating crack width in RC structures.” Struct. Concr. 17 (3): 365–376. https://doi.org/10.1002/suco.201500033.
Dörr, K. 1978. “Bond-behaviour of ribbed reinforcement under transversal pressure.” In Proc., IASS Symposium on Nonlinear Behaviour of Reinforced Concrete Spatial Structures, 13–24. Düsseldorf, Germany: Werner Verlag.
Edwards, A. D., and A. Picard. 1972. “Theory of cracking in concrete members.” J. Struct. Div. 98 (12): 2687–2700.
Eligehausen, R., E. P. Popov, and V. V. Bertero. 1983. Local bond stress-slip relationships of deformed bars under generalized excitations: Experimental results and analytical model. Berkeley, CA: Univ. of California.
Fantilli, A. P., H. Mihashi, and P. Vallini. 2007. “Crack profile in RC, R/FRCC and R/HPFRCC members in tension.” Mater. Struct. 40 (10): 1099–1114. https://doi.org/10.1617/s11527-006-9208-7.
fib. 2000. Bond of reinforcement in concrete: State-of-the-art report. fib Bulletin No. 10. Lausanne, Switzerland: Sprint-Druck Stuttgart.
fib. 2013. fib model code for concrete structures 2010. Berlin: International Federation for Structural Concrete, Ernst & Sohn.
Gergely, P., and L. A. Lutz. 1968. Maximum crack width in reinforced concrete flexural members. Farmington Hills, MI: American Concrete Institute.
Goto, Y. 1971. “Crack formed in concrete around deformed tension bars.” ACI J. 68 (4): 244–251.
Hong, S., and S. K. Park. 2012. “Uniaxial bond stress-slip relationship of reinforcing bars in concrete.” Adv. Mater. Sci. Eng. 2012 (1): 328570. https://doi.org/10.1155/2012/328570.
Husain, S. I., and P. M. Ferguson. 1968. Flexural crack width at the bars in reinforced concrete beams. Austin, TX: Center for Highway Research, Univ. of Texas.
Irgens, F. 2008. Continuum mechanics. Bergen, Norway: Springer.
Kaklauskas, G. 2017. “Crack model for RC members based on compatibility of stress-transfer and mean-strain approaches.” J. Struct. Eng. 143 (9): 04017105. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001842.
Leonhardt, F. 1988. “Cracks and crack control in concrete structures.” PCI J. 33 (4): 124–145. https://doi.org/10.15554/pcij.07011988.124.145.
Lutz, L. A. 1970. “Analysis of stresses in concrete near a reinforcing bar due to bond and transverse cracking.” ACI J. 67 (10): 778–787.
Martin, H. 1973. “On the interrelation among surface roughness, bond and bar stiffness in the reinforcement subject to short-term loading.” [In German.] Deutscher Ausschuss Stahlbeton 228: 1–50.
Mirza, S. M., and J. Houde. 1979. “Study of bond stress-slip relationships in reinforced concrete.” ACI J. 76 (1): 19–46.
Nilson, A. H. 1972. “Internal measurement of bond slip.” ACI J. 69 (7): 439–441.
NPRA (Norwegian Public Roads Administration). 2015. N400 Bruprosjektering: Prosjektering av bruer, ferjekaier og andre bærende konstruksjoner: N400 in Statens vegvesens håndbokserie. Oslo, Norway: Statens Vegvesen.
Pedziwiatr, J. 2008. “Influence of internal cracks on bond in cracked concrete structures.” Arch. Civil Mech. Eng. 8 (3): 91–105. https://doi.org/10.1016/S1644-9665(12)60165-4.
Rehm, G. 1961. “On the fundamentals of the steel-concrete bond.” [In German.] Deutscher Ausschuss für Stahlbeton 138: 1–59.
Russo, G., and F. Romano. 1992. “Cracking response of RC members subjected to uniaxial tension.” J. Struct. Eng. 118 (5): 1172–1190. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:5(1172).
Russo, G., G. Zingone, and F. Romano. 1990. “Analytical solution for bond-slip of reinforcing bars in R.C. joints.” J. Struct. Eng. 116 (2): 336–355. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:2(336).
Saliger, R. 1936. “High-grade steel in reinforced concrete.” In Proc., 2nd Congress of the Int. Association for Bridge and Structural Engineering, 293–315. Zurich, Switzerland: ETH Zürich.
Tammo, K., and S. Thelandersson. 2009. “Crack behavior near reinforcing bars in concrete structures.” ACI Struct. J. 106 (3): 259–267.
Tan, R., K. Eileraas, O. Opkvitne, G. Žirgulis, M. A. Hendriks, M. Geiker, D. E. Brekke, and T. Kanstad. 2018a. “Experimental and theoretical investigation of crack width calculation methods for RC ties.” Struct. Concr. 19 (5): 1436–1447. https://doi.org/10.1002/suco.201700237.
Tan, R., M. A. N. Hendriks, M. Geiker, and T. Kanstad. 2018b. “A numerical investigation of the cracking behaviour of reinforced concrete tie elements.” Mag. Concr. Res. https://doi.org/10.1680/jmacr.18.00156.
Tan, R., M. A. N. Hendriks, and T. Kanstad. 2018c. “An investigation of the strain profile over the cover in reinforced concrete elements subjected to tension.” In Proc., fib Congress. Melbourne, Australia: FIB Congress 2018.
Watstein, D., and R. G. Mathey. 1959. “Width of cracks in concrete at the surface of reinforcing steel evaluated by means of tensile bond specimens.” ACI J. 56 (7): 47–56.
Yannopoulos, P. J. 1989. “Variation of concrete crack widths through the concrete cover to reinforcement.” Mag. Concr. Res. 41 (147): 63–68. https://doi.org/10.1680/macr.1989.41.147.63.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Apr 16, 2018
Accepted: Jun 17, 2019
Published online: Dec 12, 2019
Published in print: Feb 1, 2020
Discussion open until: May 12, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.