Experimental Study of Disproportionate Collapse Prevention Mechanisms for Mass-Timber Floor Systems
Publication: Journal of Structural Engineering
Volume 146, Issue 2
Abstract
This paper presents and discusses experiments examining the responses of mass-timber floor systems under idealized removal of an interior load-bearing wall. Testing was performed on continuous double-span () and discontinuous single-span () floor assemblies with both conventional (lap-joint and self-tapping screws) and novel (additional internal steel tubes) floor-to-floor panel connection detailing. The continuous floor systems depended solely on the panels’ bending resistance, and brittle failure occurred at a deflection of 6% of . Improved performance associated with ductile behavior was obtained with the introduction of floor-to-floor connections with maximum deflections of 8% and 12% of for conventional and novel detailing, respectively. For the floors with conventional connection detailing, failure was observed after compressive arching due to the low axial strength and ductility. The addition of steel tubes enabled catenary action, in which the floor systems maintained high load-carrying capacity while undergoing large deflections. This study demonstrated that adequate connection detailing can ensure structural robustness of mass-timber floors for disproportionate collapse prevention.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The support by MyTiCon Connectors, Canada; Simpson Strong-Tie, Canada; and Structurlam Mass Timber, Canada is acknowledged. The support provided by George Lee, technician at the University of British Columbia Wood Mechanics Lab, and Dr. Marjan Popovski, principal scientist at FPInnovations, is much appreciated.
References
Arup. 2011. Review of international research on structural robustness and disproportionate collapse. London: Dept. for Communities and Local Government.
Atlas Tubes Canada. 2018. “Material test report.” Accessed July 26, 2018. https://www.metalsupermarkets.com/.
Brett, C., and Y. Lu. 2013. “Assessment of robustness of structures: Current state of research.” Front. Struct. Civ. Eng. 7 (4): 356–368. https://doi.org/10.1007/s11709-013-0220-z.
CEN (European Committee for Standardisation). 2006. EN1991-1-7 Actions on structures: Part 1-7: Accidental actions. Eurocode 1. Brussels, Belgium: CEN.
Connolly, T., C. Loss, A. Iqbal, and T. Tannert. 2018. “Feasibility study of mass-timber cores for the UBC tall wood building.” Buildings 8 (8): 98. https://doi.org/10.3390/buildings8080098.
DoD (Department of Defense). 2013. Unified facilities criteria: Design of buildings to resist progressive collapse. UFC 4-023-03. Washington, DC: DoD.
Gagnon, S., and C. Pirvu. 2011. CLT handbook: Cross-laminated timber. Pointe-Claire, QC: FPInnovations.
Gudmundsson, G. V., and B. A. Izzuddin. 2010. “The ‘sudden column loss’ idealisation for disproportionate collapse assessment.” Struct. Eng. 88 (6): 22–26.
Hewson, N. 2016. Robustness in structures. Melbourne, Australia: Forest and Wood Products Australia.
Hossain, A., M. Popovski, and T. Tannert. 2018. “Cross-laminated timber connections assembled with a combination of screws in withdrawal and screws in shear.” Eng. Struct. 168 (Aug): 1–11. https://doi.org/10.1016/j.engstruct.2018.04.052.
Huber, J. A. J., M. Ekevad, S. Berg, and U. A. Girhammar. 2018a. “Assessment of connections in cross-laminated timber buildings regarding structural robustness.” In Proc., World Conf. on Timber Engineering. Seoul, South Korea.
Huber, J. A. J., M. Ekevad, S. Berg, and U. A. Girhammar. 2018b. “Structural robustness and timber buildings: A review.” Wood Mater. Sci. Eng. 14 (2): 107–128. https://doi.org/10.1080/17480272.2018.1446052.
IStructE (Institution of Structural Engineers). 2010. Practical guide to structural robustness and disproportionate collapse in buildings. London: The Institution of Structural Engineers.
Khandelwal, K., S. El-Tawil, and F. Sadek. 2009. “Progressive collapse analysis of seismically designed steel braced frames.” J. Constr. Steel Res. 65 (3): 699–708. https://doi.org/10.1016/j.jcsr.2008.02.007.
Li, Y., X. Lu, H. Guan, and L. Ye. 2011. “An improved tie force method for progressive collapse resistance design of reinforced concrete frame structures.” Eng. Struct. 33 (10): 2931–2942. https://doi.org/10.1016/j.engstruct.2011.06.017.
Louisiana Pacific. 2018. “LP SolidStart laminated strand lumber (LSL) and laminated veneer lumber (LVL).” Accessed August 14, 2018. https://lpcorp.com/.
Lyu, C., B. Gilbert, S. Gunala, H. Karampour, I. Underhill, M. Masaeli, and H. Guan. 2018. “Progressive collapse (robustness) behaviour of mid-rise mass timber frame buildings.” In Proc., World Conf. on Timber Engineering. Mount Gravatt, Australia: Griffith Univ.
Main, J., Y. Bao, F. Sadek, and H. Lew. 2011. “Experimental and computational assessment of robustness of steel and reinforced concrete framed buildings.” Accessed May 20, 2018. https://ws680.nist.gov/publication/get_pdf.cfm?pub_id=907519.
Mpidi Bita, H., N. Currie, and T. Tannert. 2018. “Disproportionate collapse analysis of mid-rise cross-laminated timber buildings.” Struc. Infrastruct. Eng. 14 (11): 1547–1560. https://doi.org/10.1080/15732479.2018.1456553.
Mpidi Bita, H., and T. Tannert. 2018. “Numerical optimisation of novel connection for cross-laminated timber buildings.” Eng. Struct. 175 (Nov): 273–283. https://doi.org/10.1016/j.engstruct.2018.08.020.
Mpidi Bita, H., and T. Tannert. 2019a. “Disproportionate collapse prevention analysis for mid-rise flat-plate cross-laminated timber building.” Eng. Struct. 178 (Jan): 460–471. https://doi.org/10.1016/j.engstruct.2018.10.048.
Mpidi Bita, H., and T. Tannert. 2019b. “Tie-force procedure for disproportionate collapse prevention for CLT platform-type construction.” Eng. Struct. 189 (Jun): 195–205. https://doi.org/10.1016/j.engstruct.2019.03.074.
MyTiCon. 2017. “Structural screw: Design guide.” Accessed October 25, 2018. http://www.my-ti-con.com.
NBCC (National Building Code of Canada). 2015. National building code of Canada 2015, Canadian commission on building and fire codes. Ottawa: National Research Council of Canada.
Nordic Structures. 2018. “Origine, 13-storey building.” Accessed June 19, 2018. https://www.nordic.ca.
Popovski, M., and I. Gavric. 2015. Design models for CLT shearwalls and assemblies based on connection properties. Pointe-Claire, QC: FPInnovation.
Popovski, M., and I. Gavric. 2016. “Performance of a 2-story CLT house subjected to lateral loads.” J. Struct. Eng. 142 (4): E4015006. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001315.
Praxair. 2018. “Praxair’s StarGold C-20 and C-25.” Accessed September 13, 2018. https://www.praxair.com.
Ruth, P., K. A. Marchand, and E. B. Williamson. 2006. “Static equivalency in progressive collapse alternate path analysis: Reducing conservatism while retaining structural integrity.” J. Perform. Constr. Facil. 20 (4): 349–364. https://doi.org/10.1061/(ASCE)0887-3828(2006)20:4(349).
Sadek, F., J. Main, H. Lew, S. Robert, V. Chiarito, and S. El-Tawil. 2010. An experimental and computational study of steel moment connections under a column removal scenario. Gaithersburg, MD: National Institute of Standards and Technology.
Schneider, J., T. Tannert, S. Tesfamariam, and S. F. Stiemer. 2018. “Experimental assessment of a novel steel tube connection in cross-laminated timber.” Eng. Struct. 177: 283–290.
Schultz, D. M., E. F. P. Burnett, and M. Fintel. 1977. Design and construction of large-panel concrete structures: A design approach to general structural integrity (Report 4). Washington, DC: Portland Cement Association.
Simpson Strong-Tie. 2018. “Wood construction connector: Canadian limit states design C-C-CAN2018.” Accessed November 10, 2018. https://www.strongtie.com.
Starossek, U. 2006. “Progressive collapse of structures: Nomenclature and procedures.” Struct. Eng. Int. 16 (2): 113–117. https://doi.org/10.2749/101686606777962477.
STA (Structural Timber Association). 2017. STA advice notes 14: Robustness of CLT structures. London: STA.
Stevens, D. J. 2008. Assessment and proposed approach for tie forces in frames and loadbearing wall structures. Austin, TX: Protection Engineering Consultants.
Structurlam. 2018. “Crosslam CLT: Technical design guide.” Accessed October 14, 2018. http://www.structurlam.com.
Stylianidis, P. M. 2011. “Progressive collapse response of steel and composite buildings.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Imperial College London.
Stylianidis, P. M., D. A. Nethercot, B. A. Izzuddin, and A. Y. Elghazouli. 2016. “Study of the mechanics of progressive collapse with simplified beam models.” Eng. Struct. 117 (Jun): 287–304. https://doi.org/10.1016/j.engstruct.2016.02.056.
Tannert, T., M. Follesa, M. Fragiacomo, P. Gonzalez, H. Isoda, D. Moroder, H. Xiong, and J. van de Lindt. 2018. “Seismic design of cross-laminated timber buildings.” Wood Fiber Sci. 50: 3–26. https://doi.org/10.22382/wfs-2018-037.
Tohidi, M. 2015. “Effect of floor-to-floor joint design on the robustness of precast concrete cross wall buildings.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Birmingham.
Weigan, J., Y. Bao, and J. Main. 2017. “Acceptance criteria for the nonlinear alternative load path analysis of steel and reinforced concrete frames structures.” In Proc., ASCE Structures Congress. Reston, VA: ASCE.
Wells, M. 2011. Tall timber buildings: Applications of solid timber construction in multistorey buildings. Chicago: Council on Tall Buildings and Urban Habitat.
Weyerhaeuser. 2018. “TimberStand LSL beams.” Accessed July 22, 2018. https://www.weyerhaeuser.com.
Winter, S., and H. Kreuzinger. 2008. “The Bad Reichenhall ice-arena collapse and the necessary consequences for wide span timber structures.” In Proc., World Conf. on Timber Engineering. Wien, Austria: Vienna Univ. of Technology.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jan 2, 2019
Accepted: Jun 4, 2019
Published online: Dec 6, 2019
Published in print: Feb 1, 2020
Discussion open until: May 6, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.