Torsional Brace Strength Requirements for Steel I-Girder Systems
Publication: Journal of Structural Engineering
Volume 146, Issue 1
Abstract
Effective stability bracing of beams can be achieved by either preventing lateral movement of the compression flange or restraining twist of the beam cross section. Bracing that restrains twist is aptly referred to as torsional bracing. Adequate stability bracing must satisfy both stiffness and strength requirements. The torsional brace strength requirement in the latest edition of the AISC specification (2016) was significantly changed from the previous edition of the specification (2010). This paper presents a parametric study on the strength requirements of beam torsional bracing. An overview of the many factors affecting bracing behavior is provided. The paper demonstrates that the latest expression results in brace strength predictions that can be significantly nonconservative. The paper recommends a return to the strength provisions provided in previous editions of the specification.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the China Scholarship Council for the financial support (201706260122) of Yangqing Liu in allowing him to participate in this research effort at the University of Texas at Austin.
References
AASHTO. 2017. AASHTO LRFD bridge design specifications. 8th ed. Washington, DC: AASHTO.
AISC. 2010. Specification for structural steel buildings. Chicago: AISC.
AISC. 2016. Steel construction manual. 15th ed. Chicago: AISC.
Han, L., and T. Helwig. 2016. “Effect of girder continuity and imperfections on system buckling of narrow I-girder systems.” In Proc., Structural Stability Research Concil/North American Steel Construction Conf. Orlando, FL: Structural Stability Research Council.
Helwig, T., and J. Yura. 2015. In Vol. 13 Bracing system design. Washington, DC: US DOT, Federal Highway Administration.
Helwig, T., J. Yura, and K. Frank. 1993. “Bracing forces in diaphragms and cross frames.” In Proc., Structural Stability Research Council Conf., 129–140. Milwakee, WI: Structural Stability Research Council.
Prado, E., and D. W. White. 2015. “Assessment of basic steel I-section beam bracing requirements by test simulation.” M.S. thesis, School of Civil and Environmental Engineering, Georgia Institute of Technology.
Taylor, A. C., and M. Ojalvo. 1966. “Torsional restraint of lateral buckling.” J. Struct. Div. 92 (ST2): 115–129.
Timoshenko, S., and J. Gere. 1961. Theory of elastic stability. New York: McGraw Hill.
Wang, L., and T. A. Helwig. 2005. “Critical imperfections for beam bracing systems.” J. Struct. Eng. 131 (6): 933–940. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:6(933).
Winter, G. 1960. “Lateral bracing of columns and beams.” Trans. Am. Soc. Civ. Eng. 125 (1): 809–825.
Yura, J., T. Helwig, R. Herman, and C. Zhou. 2008. “Global lateral buckling of I-shaped girder systems.” J. Struct. Eng. 134 (9): 1487–1494.
Yura, J. A. 2001. “Fundamentals of beam bracing.” Eng. J. 38 (1): 11–26.
Yura, J. A., B. Philip, S. Raju, and S. Webb. 1992. Bracing of steel beams in bridges. Austin, TX: Center for Transportation Research, Univ. of Texas at Austin.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jan 24, 2019
Accepted: Jun 2, 2019
Published online: Nov 13, 2019
Published in print: Jan 1, 2020
Discussion open until: Apr 13, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.