Behavior of Octagonal High-Strength Steel Tubular Stub Columns
Publication: Journal of Structural Engineering
Volume 145, Issue 12
Abstract
This paper investigates the behavior of octagonal high-strength steel tubular cross sections under axial compression. Experimental investigations were conducted on cross sections with three nominal dimensions fabricated from different routes of welding or combinations of cold-bending and welding. Material properties and geometric imperfections of the cross sections were measured and are reported here. A total of 18 stub column tests were carried out; load-deformation histories and failure modes of octagonal high-strength steel tubular-section stub columns are presented and discussed. Nonlinear finite-element models were validated to replicate the stub column tests and subsequently applied to carry out parametric studies for further investigating the structural performance of octagonal tubular cross sections with various slenderness values under axial compression. The results from experiments and finite-element modeling are used to evaluate the applicability of codified cross-section classification limits and various existing design methods to octagonal high-strength steel tubular cross sections under axial compression. Modifications to the cross-section classification limits and design methods are proposed to obtain more accurate predictions of cross-section classification and strengths of structures for efficient structural design.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research described in this paper was supported by a grant from the Research Grants Council of Hong Kong Special Administrative Region, China (Project No. 15249216). The authors also thank the Construction Industry Council and the Chinese National Engineering Research Centre for Steel Construction (Hong Kong Branch) at The Hong Kong Polytechnic University for their support.
References
Alechnavičius, V., and J. Bálint. 2014. “Long span high strength steel trusses.” Master’s thesis, Dept. of Civil, Environmental and Natural Resources Engineering, Luleå Univ. of Technology.
ANSI/AISC. 2016. Specification for structural steel buildings. ANSI/AISC 360. Chicago: AISC.
Aoki, T., Y. Migita, and Y. Fukumoto. 1991. “Local buckling strength of closed polygon folded section columns.” J. Constr. Steel Res. 20 (4): 259–270. https://doi.org/10.1016/0143-974X(91)90077-E.
ASCE/SEI. 2011. Design of steel transmission pole structures. ASCE/SEI 48. Reston, VA: ASCE/SEI.
Ban, H. Y., and G. Shi. 2018. “Overall buckling behaviour and design of high-strength steel welded section columns.” J. Constr. Steel Res. 143 (Apr): 180–195. https://doi.org/10.1016/j.jcsr.2017.12.026.
Bulson, P. S. 1969. “The strength of thin-walled tubes formed from flat elements.” Int. J. Mech. Sci. 11 (7): 613–620. https://doi.org/10.1016/0020-7403(69)90060-5.
Cannon, D. D., and R. A. LeMaster. 1987. Local buckling strength of polygonal tubular poles. Haslet, TX: Transmission Line Mechanical Research Center.
CEN (European Committee for Standardization). 2002. Eurocode: Basis of structural design. EN 1990. Brussels: CEN.
CEN (European Committee for Standardization). 2005. Eurocode 3: Design of steel structures. 1-1: General rules and rules for buildings. EN 1993-1-1. Brussels: CEN.
CEN (European Committee for Standardization). 2006. Eurocode 3: Design of steel structures. Part 1-5: Plated structural elements. EN 1993-1-5. Brussels: CEN.
Chan, T. M., X. L. Zhao, and B. Young. 2015. “Cross-section classification for cold-formed and built-up high strength carbon and stainless steel tubes under compression.” J. Constr. Steel Res. 106 (Mar): 289–295. https://doi.org/10.1016/j.jcsr.2014.12.019.
Currance, W. C. 1974. “Local buckling stability of polygonal cross sections in bending.” In ASCE National Water Resources Meeting. Reston, VA: ASCE.
Dawson, R. G., and A. C. Walker. 1972. “Post-buckling of geometrically imperfect plates.” J. Struct. Div. 98 (1): 75–94.
Fang, H., and T. M. Chan. 2018. “Axial compressive strength of welded S460 steel columns at elevated temperatures.” Thin-Walled Struct. 129 (Aug): 213–224. https://doi.org/10.1016/j.tws.2018.04.006.
Fang, H., and T. M. Chan. 2019. “Buckling resistance of welded high-strength-steel box-section members under combined compression and bending.” J. Constr. Steel Res. 162: 105711.
Fang, H., T. M. Chan, and B. Young. 2018a. “Material properties and residual stresses of octagonal high strength steel hollow sections.” J. Constr. Steel Res. 148 (Sep): 479–490. https://doi.org/10.1016/j.jcsr.2018.06.007.
Fang, H., T. M. Chan, and B. Young. 2018b. “Structural performance of cold-formed high strength steel tubular columns.” Eng. Struct. 177: 473–488.
Gardner, L., N. Saari, and F. Wang. 2010. “Comparative experimental study of hot-rolled and cold-formed rectangular hollow sections.” Thin-Walled Struct. 48 (7): 495–507. https://doi.org/10.1016/j.tws.2010.02.003.
Godat, A., F. Legeron, and D. Bazonga. 2012. “Stability investigation of local buckling behaviour of tubular polygon columns under concentric compression.” Thin-Walled Struct. 53 (Apr): 131–140. https://doi.org/10.1016/j.tws.2011.12.013.
Gonçalves, R., and D. Camotim. 2013. “Elastic buckling of uniformly compressed thin-walled regular polygonal tubes.” Thin-Walled Struct. 71 (Oct): 35–45. https://doi.org/10.1016/j.tws.2013.04.016.
Lan, X. Y., J. B. Chen, T. M. Chan, and B. Young. 2018. “The continuous strength method for the design of high strength steel tubular sections in compression.” Eng. Struct. 162: 177–187. https://doi.org/10.1016/j.engstruct.2018.02.010.
Ma, J. L., T. M. Chan, and B. Young. 2015. “Material properties and residual stresses of cold-formed high strength steel hollow sections.” J. Constr. Steel Res. 109 (Jun): 152–165. https://doi.org/10.1016/j.jcsr.2015.02.006.
Ma, J. L., T. M. Chan, and B. Young. 2016a. “Experimental investigation of cold-formed high strength steel tubular beams.” Eng. Struct. 126 (Nov): 200–209. https://doi.org/10.1016/j.engstruct.2016.07.027.
Ma, J. L., T. M. Chan, and B. Young. 2016b. “Experimental investigation on stub-column behavior of cold-formed high strength steel tubular sections.” J. Struct. Eng. 142 (5): 04015174. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001456.
Ma, J. L., T. M. Chan, and B. Young. 2017. “Experimental investigation on cold-formed high strength steel circular hollow sections under combined compression and bending.” In Proc., 8th European Conf. on Steel and Composite Structures, 3622–3630. Berlin: Wilhelm Ernst und Sohn.
Manoleas, P., E. Koltsakis, and M. Veljkovic. 2017. “Multiplanar K-joints on cold-formed open sections.” In Proc., 8th European Conf. on Steel and Composite Structures, 629–638. Berlin: Wilhelm Ernst und Sohn.
Migita, Y., and Y. Fukumoto. 1997. “Local buckling behaviour of polygonal sections.” J. Constr. Steel Res. 41 (2–3): 221–233. https://doi.org/10.1016/S0143-974X(97)00008-4.
Naohiro, W., I. Kikuo, O. Tadayoshi, and K. Yosuke. 2017. “Local buckling behaviour of octagonal hollow cross-section member under axial compression or bending shear.” In Proc., 8th European Conf. on Steel and Composite Structures, 1116–1122. Berlin: Wilhelm Ernst und Sohn.
Niu, S., K. R. Rasmussen, and R. Feng. 2015. “Local-global interaction buckling of stainless steel I-beams. II: Numerical study and design.” J. Struct. Eng. 141 (8): 04014195. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001131.
Rasmussen, K. R., and G. J. Hancock. 1993. “Design of cold-formed stainless steel tubular members. I: Columns.” J. Struct. Eng. 119 (8): 2349–2367. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:8(2349).
Somodi, B., and B. Kövesdi. 2017. “Residual stress measurements on cold-formed HSS hollow section columns.” J. Constr. Steel Res. 128 (Jan): 706–720. https://doi.org/10.1016/j.jcsr.2016.10.008.
Wang, J., S. Afshan, M. Gkantou, M. Theofanous, C. Baniotopoulos, and L. Gardner. 2016. “Flexural behavior of hot-finished high strength steel square and rectangular hollow sections.” J. Constr. Steel Res. 121 (Jun): 97–109. https://doi.org/10.1016/j.jcsr.2016.01.017.
Wang, J., S. Afshan, N. Schillo, M. Theofanous, M. Feldmann, and L. Gardner. 2017. “Material properties and compressive local buckling response of high strength steel square and rectangular hollow sections.” Eng. Struct. 130 (Jan): 297–315. https://doi.org/10.1016/j.engstruct.2016.10.023.
Wang, J., and L. Gardner. 2017. “Flexural buckling of hot-finished high-strength steel SHS and RHS columns.” J. Struct. Eng. 143 (6): 04017028. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001763.
Wardenier, J., J. A. Packer, X. L. Zhao, and G. J. van der Vegte. 2010. Hollow sections in structural applications. 2nd ed. Geneva: Comité International pour le Développement et l'Etude de la Construction Tubulaire.
Zhao, O., L. Gardner, and B. Young. 2016. “Buckling of ferritic stainless steel members under combined axial compression and bending.” J. Constr. Steel Res. 117 (Feb): 35–48. https://doi.org/10.1016/j.jcsr.2015.10.003.
Zhu, J. Y., T. M. Chan, and B. Young. 2019. “Cross-sectional capacity of octagonal tubular steel stub columns under uniaxial compression.” Eng. Struct. 184 (Apr): 480–494. https://doi.org/10.1016/j.engstruct.2019.01.066.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Sep 22, 2018
Accepted: Mar 22, 2019
Published online: Sep 21, 2019
Published in print: Dec 1, 2019
Discussion open until: Feb 21, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.