Performance of CFS Beam-to-Beam Bolted Connection Using Clip Angle and Flange Strip: Experimental Investigation
Publication: Journal of Structural Engineering
Volume 145, Issue 10
Abstract
This paper presents an experimental investigation on the strength, load versus deflection, and load versus rotation behavior of cold-formed steel (CFS) beam-to-beam connections using a combination of clip angle and flange strip through the use of bolts and self-drilling screws in the webs and flanges, respectively. A total of 24 tests with four different aspect ratios in the loaded leg and three different aspect ratios in the anchored leg for two different clip angle thickness were carried out under four-point bending to study the strength and different failure modes under flexure. The dimension and number of screws in the flange strip connecting the top flanges of the channels to provide restraint against end lateral displacement and rotation at both ends of connection were kept constant. The results indicate that the end rotation depends on the number of bolts in the clip angle connected to the loaded channel and the thickness of the clip angle. A higher degree of stiffness was exhibited by the three-bolt configuration for both thicknesses of the clip angle. The optimum anchored aspect ratio with regard to the strength was found to be 1.0 and 1.5 for the clip angle thicknesses of 0.8 and 1.5 mm, respectively. Three different failure modes were observed in the clip angle: local buckling, distortional buckling, and bearing in the bolt hole. The ultimate strength increased up to 70% due to the flange strip connection provided at the top of flanges by the application of self-drilling screws. Comparison of the experimental results with literature study indicates the literature approach is ultraconservative in both serviceability and ultimate state. Based on the test results, a new design method was developed for determining the nominal shear strength with consideration of deformation. The load and resistance factor design (LRFD) resistance factor and allowable strength (ASD) safety factor were found to support the modified design equation.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The first author would like to acknowledge the fellowship from the Ministry of Human Resource Development (MHRD) India. The authors would like to gratefully acknowledge Pennar Engineered Building Systems Ltd., Hyderabad for their help in fabricating the test specimens required for experimental investigation.
References
AISI (American Iron and Steel Institute). 2012. North American specification for the design of cold-formed steel structural members, 2012 edition. AISI S100. Washington, DC: AISI.
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. AISI S100. Washington, DC: AISI.
ASTM. 2016. Standard test methods and definitions for mechanical testing of steel products. ASTMA370. West Conshohocken, PA: ASTM.
Chung, K. F., and L. Lau. 1999. “Experimental investigation on bolted moment connections among cold formed steel members.” Eng. Struct. 21 (10): 898–911. https://doi.org/10.1016/S0141-0296(98)00043-1.
Chung, K. F., and R. M. Lawson. 2000. “Structural performance of shear resisting connections between cold-formed steel sections using web cleats of cold-formed steel strip.” Eng. Struct. 22 (10): 1350–1366. https://doi.org/10.1016/S0141-0296(99)00083-8.
Fastenal Industrial and Construction Supplies. 2005. Technical reference guide. Winona, MN: Fastenal Industrial and Construction Supplies.
Fox, S. 2005. Strength of CFS floor assemblies with clip angle bearing stiffeners. Washington, DC: American Iron and Steel Institute.
ICC-ES (International Code Council Evaluation Service). 2011. AC261 connectors used with cold-formed steel structural members-Approved October 2011. Brea, CA: ICC-ES.
Mills, J., and R. LaBoube. 2004. “Self-drilling screw joints for cold-formed channel portal frames.” J. Struct. Eng. 130 (11): 1799–1806. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:11(1799).
Natesan, V., and M. Madhavan. 2017. “Rotational behavior of cold-formed steel beams connected through clip angles.” In Proc., 8th European Conf. on Steel and Composite Structures, 1580–1589. Berlin: Ernst & Sohn Verlag.
Natesan, V., and M. Madhavan. 2019a. “Experimental investigation on clip angle bolted connection between two cold-formed steel channels.” Struct. Build. https://doi.org/10.1680/jstbu.18.00134.
Natesan, V., and M. Madhavan. 2019b. “Experimental study on beam-to-column clip angle bolted connection.” Thin-Walled Struct. 141: 540–553.
Yu, C., M. Yousof, and M. Mahdavian. 2015. Load bearing clip angle design. Washington, DC: American Iron and Steel Institute.
Yu, C., M. Yousof, M. Mahdavian, and W. Zhang. 2016. “Behavior and design of thin-walled cold-formed steel clip angles subjected to shear load.” J. Struct. Eng. 142 (7): 04016040. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001493.
Yu, C., M. Yousof, M. Mahdavian, and W. Zhang. 2017. “Design of cold-formed steel clip angles in compression.” J. Struct. Eng. 143 (6): 04017030. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001767.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Mar 30, 2018
Accepted: Feb 22, 2019
Published online: Jul 26, 2019
Published in print: Oct 1, 2019
Discussion open until: Dec 26, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.