Structural Behavior of Composite Panels Made of Lightly Profiled Steel Skins and Lightweight Concrete under Concentric and Eccentric Loads
Publication: Journal of Structural Engineering
Volume 145, Issue 10
Abstract
This paper addresses the structural performance of a type of sandwich panels with lightly profiled thin steel skins filled with lightweight concrete. A series of experimental tests and numerical simulations were conducted on the composite panels subjected to concentric and eccentric compressive loads and flexural loads. Both results show that skin buckling is the governing criterion for the load carrying capacity of this structural component. Based on the contact buckling theory, practical formulas were developed for section capacity prediction of the composite panels. The experimental results, numerical simulation, and formula prediction results agree well with each other.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful for the guidance and mentoring from Prof. John Warwick Butterworth (1942–2017) in the research project Composite Structural Assemblies (CSA). The financial support from the New Zealand Foundation for Research, Science, and Technology is appreciated.
References
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete. ACI 318. Farmington Hills, MI: ACI.
AS (Standards Australia) and Standards New Zealand. 2005. Cold-formed steel structures. AS/NZS 4600. Sydney, Australia: AS.
Brunesi, E., R. Nascimbene, M. Deyanova, C. Pagani, and S. Zambelli. 2015. “Numerical simulation of hollow steel profiles for lightweight concrete sandwich panels.” Comput. Concr. 15 (6): 951–972. https://doi.org/10.12989/cac.2015.15.6.951.
BSI (British Standards Institution). 1997. Structural use of concrete. BS-8110. London: BSI.
Chu, X. T., and T. Neitzert. 2007. Assessment of interfacial strength between galvanized steel and light-weight concrete. Auckland, New Zealand: Community Supported Agriculture.
Flores-Johnson, E. A., and Q. M. Li. 2012. “Structural behaviour of composite sandwich panels with plain and fibre-reinforced foamed concrete cores and corrugated steel faces.” Compos. Struct. 94 (5): 1555–1563. https://doi.org/10.1016/j.compstruct.2011.12.017.
Hilo, S. J., W. H. W. Badaruzzaman, S. A. Osman, A. W. Al-Zand, M. Samir, and Q. A. Hasan. 2015. “A state-of-the-art review on double-skinned composite wall systems.” Thin-Walled Struct. 97: 74–100. https://doi.org/10.1016/j.tws.2015.09.007.
Hossain, K. M. A., S. Rafiei, M. Lachemi, K. Behdinan, and M. S. Anwar. 2016. “Finite element modeling of impact shear resistance of double skin composite wall.” Thin-Walled Struct. 107: 101–118. https://doi.org/10.1016/j.tws.2016.06.002.
Hossain, K. M. A., and H. D. Wright. 1998. “Performance of profiled concrete shear panels.” J. Struct. Eng. 124 (4): 368–381. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:4(368).
Hossain, K. M. A., and H. D. Wright. 2004. “Design aspects of double skin profiled composite framed shearwalls in construction and service stages.” ACI Struct. J. 101 (1): 94–102.
Ma, X., J. W. Butterworth, and G. C. Clifton. 2008a. “Initial compressive buckling of clamped plates resting on tensionless elastic or rigid foundations.” J. Eng. Mech. 134 (6): 514–518. https://doi.org/10.1061/(ASCE)0733-9399(2008)134:6(514).
Ma, X., J. W. Butterworth, and G. C. Clifton. 2008b. “Unilateral contact buckling of lightly profiled skin sheets under compressive or shearing loads.” Int. J. Solids Struct. 45 (3–4): 840–849. https://doi.org/10.1016/j.ijsolstr.2007.09.006.
Mydin, M. A. O., and Y. C. Wang. 2011. “Structural performance of lightweight steel-foamed concrete-steel composite walling system under compression.” Thin-Walled Struct. 49 (1): 66–76. https://doi.org/10.1016/j.tws.2010.08.007.
Rafiei, S., K. M. Hossain, M. Lachemi, and K. Behdinan. 2015. “Profiled sandwich composite wall with high performance concrete subjected to monotonic shear.” J. Constr. Steel Res. 107: 124–136. https://doi.org/10.1016/j.jcsr.2015.01.015.
Schafer, B. W., and T. Pekoz. 1998. “Cold-formed steel members with multiple longitudinal intermediate stiffeners.” J. Struct. Eng. 124 (10): 1175–1181. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:10(1175).
Uy, B., H. D. Wright, and M. A. Bradford. 2001. “Combined axial and flexural strength of profiled composite walls.” Proc. ICE-Struct. Build. 146 (2): 129–139. https://doi.org/10.1680/stbu.2001.146.2.129.
Wright, H. D., and S. C. Gallocher. 1995. “The behaviour of composite walling under construction and service loading.” J. Constr. Steel Res. 35 (3): 257–273. https://doi.org/10.1016/0143-974X(94)00051-I.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Oct 5, 2017
Accepted: Feb 1, 2019
Published online: Jul 16, 2019
Published in print: Oct 1, 2019
Discussion open until: Dec 16, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.