Out-of-Plane Performance of Reinforced Masonry Shear Walls Constructed with Boundary Elements
Publication: Journal of Structural Engineering
Volume 145, Issue 8
Abstract
Reinforced masonry shear walls with boundary elements have been introduced recently as a seismic force–resisting system as alternative to traditional reinforced masonry shear walls with rectangular cross sections. The introduction of the boundary elements enhances the wall’s in-plane performance because of the confinement action of the horizontal steel ties within the boundary elements that increase the compressive strain capacity and thus improve the overall wall displacement ductility. However, the performance of such reinforced masonry shear wall system has not yet been well investigated experimentally or analytically under out-of-plane loading (e.g., blast loads). Therefore, this study evaluated the contribution of boundary elements to the wall out-of-plane performance in terms of enhanced ultimate resistance load and displacement capacities. Three reinforced masonry shear walls with boundary elements, with different reinforcement ratios and distributions, were tested under quasi-static loading to evaluate the wall displacement response, mode of failure, damage state, ductility capacity, and energy absorption. Furthermore, a numerical model was developed and used to generate additional results of walls with similar in-plane or out-of-plane load resistance to those tested experimentally, but with rectangular cross sections, to allow for a performance comparison. The results showed that reinforced masonry shear walls with boundary elements achieved higher ductility capacity and energy absorption levels compared to their counterparts with rectangular cross sections. This study presents key experimental and numerical data that will facilitate quantifying several aspects pertaining to the out-of-plane performance of reinforced masonry shear walls with boundary elements within the next editions of relevant North American codes and standards.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support for this project was provided by a Collaborative Research and Development Grant (CRDG) funded through the Natural Sciences and Engineering Research Council (NSERC) of Canada and the Canadian Concrete Masonry Producers Association (CCMPA). Provision of mason time by the Ontario Masonry Contractors Association (OMCA) and technical support by the Canada Masonry Design Centre (CMDC) is appreciated. Support was also provided by the McMaster University Centre for Effective Design of Structures (CEDS), funded through the Ontario Research and Development Challenge Fund (ORDCF) of the Ministry of Research and Innovation (MRI).
References
Abboud, B. E., A. A. Hamid, and H. G. Harris. 1990. “Small-scale modeling of concrete block masonry structures.” ACI Struct. J. 87 (2): 145–155.
Abboud, B. E., A. A. Hamid, and H. G. Harris. 1996. “Flexural behavior of reinforced concrete masonry walls under out-of-plane monotonic loads.” ACI Struct. J. 93 (3): 327–335.
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete. ACI 318M. Farmington Hills, MI: ACI.
ASCE. 2011. Blast protection of buildings. ASCE 59. Reston, VA: ASCE.
ASCE. 2014. Seismic evaluation and retrofit of existing buildings. ASCE 41-13. Reston, VA: ASCE.
Banting, B., and W. El-Dakhakhni. 2014. “Seismic performance quantification of reinforced masonry structural walls with boundary elements.” J. Struct. Eng. 140 (5): 04014001. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000895.
Bažant, Z. P., and B. H. Oh. 1983. “Crack band theory of concrete.” Mater. Struct. 16 (3): 155–177. https://doi.org/10.1007/BF02486267.
Biggs, J. M. 1964. Introduction to structural dynamics. New York: McGraw-Hill.
Cerioni, R., and G. Donida. 1994. “A finite element model for the nonlinear analysis of reinforced and prestressed masonry walls.” Comput. Struct. 53 (6): 1291–1306. https://doi.org/10.1016/0045-7949(94)90397-2.
CSA (Canadian Standards Association). 2012. Design and assessment of buildings subjected to blast loads. CSA S850. Mississauga, Canada: CSA.
CSA (Canadian Standards Association). 2014a. CSA Standards on concrete masonry units. CSA A165. Mississauga, Canada: CSA.
CSA (Canadian Standards Association). 2014b. Carbon steel bars for concrete reinforcement. CSA G30.18-09. Mississauga, Canada: CSA.
CSA (Canadian Standards Association). 2014c. Design of masonry structures. CSA S304. Mississauga, Canada: CSA.
CSA (Canadian Standards Association). 2014d. Mortar and grout for unit masonry. CSA A179. Mississauga, Canada: CSA.
Drysdale, R. G., and A. S. Essawy. 1988. “Out-of-plane bending of concrete block walls.” J. Struct. Eng. 114 (1): 121–133. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:1(121).
Dusenberry, D. O. ed. 2010. Handbook for blast resistant design of buildings. Hoboken, NJ: Wiley.
El Ezz, A. A., H. M. Seif Eldin, and K. Galal. 2015. “Influence of confinement reinforcement on the compression stress-strain of grouted reinforced concrete block masonry boundary elements.” Structures 2: 32–43. https://doi.org/10.1016/j.istruc.2015.01.001.
ElSayed, M., W. El-Dakhakhni, and M. Tait. 2016. “Resilience evaluation of seismically detailed reinforced concrete-block shear walls for blast-risk assessment.” J. Perform. Constr. Facil. 30 (4): 04015087. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000742.
Ezzeldin, M., W. El-Dakhakhni, and L. Weibe. 2017. “Experimental assessment of the system-level seismic performance of an asymmetrical reinforced concrete block wall building with boundary elements.” J. Struct. Eng. 143 (8): 04017063. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001790.
Ezzeldin, M., L. Wiebe, and W. El-Dakhakhni. 2016. “Seismic collapse risk assessment of reinforced masonry walls with boundary elements using the FEMA P695 methodology.” J. Struct. Eng. 142 (11): 04016108. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001579.
Filippou, F. C., E. P. Popov, and V. V. Bertero. 1983. Effects of bond deterioration on hysteretic behavior of reinforced concrete joints. Berkeley, CA: Earthquake Engineering Research Center, Univ. of California, Berkeley.
Hallinan, P., and H. Guan. 2007. “Layered finite element analysis of one-way and two-way concrete walls with openings.” Adv. Struct. Eng. 10 (1): 55–72. https://doi.org/10.1260/136943307780150850.
Harris, H. G., and G. M. Sabnis. 1999. Structural modeling and experimental techniques. 2nd ed. Boca Raton, FL: CRC Press.
Hatzinikolas, M., Y. Korany, and S. Brzev. 2015. Masonry design for engineers and architects. Edmonton, Canada: Canadian Masonry.
Hoiseth, K. V., and T. Kvande. 2000. “Constitutive properties of lightweight concrete masonry.” In Vol. 1 of Proc., 12th Int. Brick/Block Masonry Conf. Hannover, Germany: TIB publications.
Karapitta, L., H. Mouzakis, and P. Carydis. 2011. “Explicit finite-element analysis for the in-plane cyclic behavior of unreinforced masonry structures.” Earthquake Eng. Struct. Dyn. 40 (2): 175–193. https://doi.org/10.1002/eqe.1014.
Lotfi, H. R., and P. B. Shing. 1991. “An appraisal of smeared crack models for masonry shear wall analysis.” Comput. Struct. 41 (3): 413–425. https://doi.org/10.1016/0045-7949(91)90134-8.
Lu, X., L. Xie, H. Guan, Y. Huang, and X. Lu. 2015. “A shear wall element for nonlinear seismic analysis of super-tall buildings using OpenSees.” Finite Elem. Anal. Des. 98: 14–25. https://doi.org/10.1016/j.finel.2015.01.006.
Mander, J. B., M. J. N. Priestley, and R. Park. 1988. “Theoretical stress-strain model for confined concrete.” J. Struct. Eng. 114 (8): 1804–1826. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1804).
McKenna, F., G. L. Fenves, and M. H. Scott. 2013. Open system for earthquake engineering simulation, version 6.50. Berkeley, CA: Univ. of California, Berkeley.
Moghaddam, H., and N. Goudarzi. 2010. “Transverse resistance of masonry infills.” ACI Struct. J. 107 (4): 461–467.
Moreno-Herrera, J., J. Varela-Rivera, and L. Fernandez-Baqueiro. 2016. “Out-of-plane design procedure for confined masonry walls.” J. Struct. Eng. 142 (2): 04015126. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001391.
Park, R., and W. L. Gamble. 2000. Reinforced concrete slabs. 2nd ed. New York: Wiley.
Paulay, T., and M. Priestley. 1992. Seismic design of reinforced concrete and masonry buildings. New York: Wiley.
Rots, J. G. 1997. Structural masonry: An experimental/numerical basis for practical design rules. Rotterdam, Netherlands: A.A. Balkema.
Rots, J. G., P. Nauta, G. M. A. Kusters, and J. Blaauwendraad. 1985. “Smeared crack approach and fracture localization in concrete.” Heron 30 (1): 1–48.
Shedid, M., R. Drysdale, and W. El-Dakhakhni. 2008. “Behavior of fully grouted reinforced concrete masonry shear walls failing in flexure: Experimental results.” J. Struct. Eng. 134 (11): 1754–1767. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:11(1754).
Shedid, M. T., W. W. El-Dakhakhni, and R. G. Drysdale. 2010a. “Alternative strategies to enhance the seismic performance of reinforced concrete-block shear wall systems.” J. Struct. Eng. 136 (6): 676–689. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000164.
Shedid, M. T., W. W. El-Dakhakhni, and R. G. Drysdale. 2010b. “Characteristics of confined and unconfined masonry prisms for seismic performance enhancement of structural walls.” Masonry Int. 23 (2): 69–78.
Simonds, K. 2014. “Performance of reinforced concrete block structural walls with boundary elements under multiple design basis blast threat levels.” M.A.Sc. thesis, Dept. of Civil Engineering, McMaster Univ.
Smith, N. L., M. J. Tait, W. W. El-dakhakhni, and W. F. Mekky. 2016. “Response analysis of reinforced concrete block infill panels under blast.” J. Perform. Constr. Facil. 30 (6): 1–12. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000825.
TMS (The Masonry Society). 2016. Building code requirements and specifications for masonry structures. TMS 402-16/ACI 530-16/ASCE 5-16. Detroit: Masonry Society Publications.
Tomaževič, M. 1998. Earthquake-resistant design of masonry buildings. London: Imperial College Press.
Tu, Y.-H., T.-H. Chuang, P.-M. Liu, and Y.-S. Yang. 2010. “Out-of-plane shaking table tests on unreinforced masonry panels in RC frames.” Eng. Struct. 32 (12): 3925–3935. https://doi.org/10.1016/j.engstruct.2010.08.030.
Varela-Rivera, J., J. Moreno-Herrera, I. Lopez-Gutierrez, and L. Fernandez-Baqueiro. 2012. “Out-of-plane strength of confined masonry walls.” J. Struct. Eng. 138 (11): 1331–1341. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000578.
Varela-Rivera, J. L., D. Navarrete-Macias, L. E. Fernandez-Baqueiro, and E. I. Moreno. 2011. “Out-of-plane behaviour of confined masonry walls.” Eng. Struct. 33 (5): 1734–1741. https://doi.org/10.1016/j.engstruct.2011.02.012.
Zhang, X., S. Singh, D. K. Bull, and N. Cooke. 2001. “Out-of-plane performance of reinforced masonry walls with openings.” J. Struct. Eng. 127 (1): 51–57. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:1(51).
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Dec 28, 2017
Accepted: Nov 16, 2018
Published online: May 28, 2019
Published in print: Aug 1, 2019
Discussion open until: Oct 28, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.