Fiber-Based Nonlocal Formulation for Simulating Softening in Reinforced Concrete Beam-Columns
Publication: Journal of Structural Engineering
Volume 144, Issue 12
Abstract
A nonlocal formulation framework is presented to address mesh-dependent strain localization in displacement-based frame element models in the presence of constitutive softening. The framework consists of a nonlocal displacement-based frame element and a nonlocal fiber-based plasticity model, and is used to simulate the postpeak response of RC structural members. The algorithmic implementation of the framework is discussed, and its performance is thoroughly investigated. Mesh sensitivity studies reveal that the proposed approach eliminates mesh-dependent strain localization and leads to objective global (i.e., load displacement) and local (i.e., curvature profile) response in the presence of concrete softening. Comparison with historical test data from 24 column specimens shows that the postpeak response of RC beam-columns is predicted with reasonable accuracy. The limitations of the presented framework are discussed along with areas for further development.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Science Foundation (Grant No. CMMI 1434300) and graduate assistantships from the University of California at Davis. The findings and opinions presented in this paper are entirely those of the authors.
References
Addessi, D., and V. Ciampi. 2007. “A regularized force-based beam element with a damage-plastic section constitutive law.” Int. J. Numer. Methods Eng. 70 (5): 610–629. https://doi.org/10.1002/nme.1911.
Ang, B. G., M. J. N. Priestley, and R. Park. 1981. “Ductility of reinforced concrete bridge piers under seismic loading.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
Atalay, M. B., and J. Penzien. 1975. The seismic behavior of critical regions of reinforced concrete components as influenced by moment, shear and axial force. Berkeley, CA: Univ. of California.
Bazant, Z. P. 1976. “Instability, ductility, and size effect in strain-softening concrete.” J. Eng. Mech. Div. 102 (2): 331–344.
Bazant, Z. P. 1982. “Crack band model for fracture of geomaterials.” In Proc., 4th Int. Conf. of Numerical Methods in Geomechanics. Edmonton, AB, Canada: Citeseer.
Bažant, Z. P., and T. B. Belytschko. 1985. “Wave propagation in a strain-softening bar: Exact solution.” J. Eng. Mech. 111 (3): 381–389. https://doi.org/10.1061/(ASCE)0733-9399(1985)111:3(381).
Bažant, Z. P., and G. Di Luzio. 2004. “Nonlocal microplane model with strain-softening yield limits.” Int. J. Solids Struct. 41 (24): 7209–7240.
Bažant, Z. P., and M. Jirásek. 2002. “Nonlocal integral formulations of plasticity and damage: Survey of progress.” J. Eng. Mech. 128 (11): 1119–1149. https://doi.org/10.1061/(ASCE)0733-9399(2002)128:11(1119).
Bažant, Z. P., and F.-B. Lin. 1988a. “Non-local yield limit degradation.” Int. J. Numer. Methods Eng. 26 (8): 1805–1823. https://doi.org/10.1002/nme.1620260809.
Bažant, Z. P., and F.-B. Lin. 1988b. “Nonlocal smeared cracking model for concrete fracture.” J. Struct. Eng. 114 (11): 2493–2510. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:11(2493).
Bažant, Z. P., and B. H. Oh. 1983. “Crack band theory for fracture of concrete.” Matériaux et Constr. 16 (3): 155–177. https://doi.org/10.1007/BF02486267.
Bažant, Z. P., J. Pan, and G. Pijaudier-Cabot. 1987. “Softening in reinforced concrete beams and frames.” J. Struct. Eng. 113 (12): 2333–2347. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:12(2333).
Bažant, Z. P., and G. Pijaudier-Cabot. 1989. “Measurement of characteristic length of nonlocal continuum.” J. Eng. Mech. 115 (4): 755–767. https://doi.org/10.1061/(ASCE)0733-9399(1989)115:4(755).
Berry, M., M. Parrish, and M. Eberhard. 2004. PEER structural performance database user’s manual (version 1.0). Berkeley, CA: Univ. of California.
Brinkgreve, R. B. J. 1994. “Geomaterial models and numerical analysis of softening.” Ph.D. thesis, Delft Univ. of Technology.
Clough, R. W., K. L. Benuska, and E. L. Wilson. 1965. “Inelastic earthquake response of tall buildings.” In Vol. 11 of Proc., 3rd World Conf. on Earthquake Engineering. New Zealand.
Coleman, J., and E. Spacone. 2001. “Localization issues in force-based frame elements.” J. Struct. Eng. 127 (11): 1257–1265. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:11(1257).
El-Tawil, S., and G. G. Deierlein. 1998. “Stress-resultant plasticity for frame structures.” J. Eng. Mech. 124 (12): 1360–1370. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:12(1360).
Feng, D., X. Ren, and J. Li. 2015. “Implicit gradient delocalization method for force-based frame element.” J. Struct. Eng. 142 (2): 04015122. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001397.
Filippou, F., and A. Saritas. 2006. “A beam finite element for shear-critical RC beams.” ACI Special Publ. 237: 295–310.
Giberson, M. F. 1967. “The response of nonlinear multi-story structures subjected to earthquake excitation.” Ph.D. thesis, Dept. of Engineering and Applied Science, California Institute of Technology.
Gill, W. D., R. Park, and M. J. N. Priestley. 1979. “Ductility of rectangular reinforced concrete columns with axial load.” M.S. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
Grassl, P., and M. Jirásek. 2006. “Damage-plastic model for concrete failure.” Int. J. Solids Struct. 43 (22): 7166–7196. https://doi.org/10.1016/j.ijsolstr.2006.06.032.
Hoshikuma, J., K. Kawashima, K. Nagaya, and A. W. Taylor. 1997. “Stress-strain model for confined reinforced concrete in bridge piers.” J. Struct. Eng. 123 (5): 624–633. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:5(624).
Hughes, T. J., J. A. Cottrell, and Y. Bazilevs. 2005. “Isogeometric analysis: CAD, finite elements, NURBS, exact geometry and mesh refinement.” Comput. Methods Appl. Mech. Eng. 194 (39–41): 4135–4195. https://doi.org/10.1016/j.cma.2004.10.008.
Jansen, D. C., and S. P. Shah. 1997. “Effect of length on compressive strain softening of concrete.” J. Eng. Mech. 123 (1): 25–35. https://doi.org/10.1061/(ASCE)0733-9399(1997)123:1(25).
Jirásek, M., and S. Rolshoven. 2003. “Comparison of integral-type nonlocal plasticity models for strain-softening materials.” Int. J. Eng. Sci. 41 (13–14): 1553–1602. https://doi.org/10.1016/S0020-7225(03)00027-2.
Jirásek, M., and T. Zimmermann. 1998. “Rotating crack model with transition to scalar damage.” J. Eng. Mech. 124 (3): 277–284. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:3(277).
Kanda, M., N. Shirai, H. Adachi, and T. Sato. 1988. “Analytical study on elasto-plastic hysteretic behaviors of reinforced concrete members.” Trans. Jpn. Concr. Inst. 10 (1): 257–264.
Kolwankar, S., A. Kanvinde, M. Kenawy, and S. Kunnath. 2017. “Uniaxial nonlocal formulation for geometric nonlinearity-induced necking and buckling localization in a steel bar.” J. Struct. Eng. 143 (9): 04017091. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001827.
Kono, S., and F. Watanabe. 2000. “Damage evaluation of reinforced concrete columns under multiaxial cyclic loadings.” In Proc., 2nd US-Japan Workshop on Performance-Based Earthquake Engineering Methodology for Reinforced Concrete Building Structures, 221–231. Berkeley, CA: Pacific Earthquake Engineering Research Center.
Mander, J. B., M. J. N. Priestley, and R. Park. 1988. “Observed stress-strain behavior of confined concrete.” J. Struct. Eng. 114 (8): 1827–1849. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1827).
McKenna, F., G. L. Fenves, and M. H. Scott. 2000. “Open system for earthquake engineering simulation.” Univ. of California. http://opensees.berkeley.edu.
Menegotto, M., and P. Pinto. 1973. “Method of analysis for cyclically loaded reinforced concrete plane frames including changes in geometry and inelastic behavior of elements under combined normal force and bending.” In Proc., IABSE Symp. on Resistance and Ultimate Deformability of Structures Acted on by Well Defined Repeated Loads, Final Report. Zurich, Switzerland: International Association for Bridge and Structural Engineering.
Peerlings, R., M. Geers, R. De Borst, and W. Brekelmans. 2001. “A critical comparison of nonlocal and gradient-enhanced softening continua.” Int. J. Solids Struct. 38 (44–45): 7723–7746. https://doi.org/10.1016/S0020-7683(01)00087-7.
Pijaudier-Cabot, G., and Z. P. Bažant. 1987. “Nonlocal damage theory.” J. Eng. Mech. 113 (10): 1512–1533. https://doi.org/10.1061/(ASCE)0733-9399(1987)113:10(1512).
Planas, J., M. Elices, and G. V. Guinea. 1993. “Cohesive cracks versus nonlocal models: Closing the gap.” Int. J. Fract. 63 (2): 173–187. https://doi.org/10.1007/BF00017284.
Powell, G. H., and P. F.-S. Chen. 1986. “3D beam-column element with generalized plastic hinges.” J. Eng. Mech. 112 (7): 627–641. https://doi.org/10.1061/(ASCE)0733-9399(1986)112:7(627).
Pugh, J. S., L. N. Lowes, and D. E. Lehman. 2015. “Nonlinear line-element modeling of flexural reinforced concrete walls.” Eng. Struct. 104: 174–192. https://doi.org/10.1016/j.engstruct.2015.08.037.
Razvi, S., and M. Saatcioglu. 1999. “Confinement model for high-strength concrete.” J. Struct. Eng. 125 (3): 281–289. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:3(281).
Razvi, S. R. 1988. “Behavior of reinforced concrete columns confined with welded wire fabric.” M.A.Sc. thesis, Dept. of Civil Engineering, Univ. of Ottawa.
Rolshoven, S. 2003. “Nonlocal plasticity models for localized failure.” Ph.D. thesis, Civil Engineering Section, École Polytechnique Fédérale de Lausanne.
Saatcioglu, M., and M. Grira. 1999. “Confinement of reinforced concrete columns with welded reinforced grids.” ACI Struct. J. 96 (1): 29–39.
Scott, B. D., R. Park, and M. J. N. Priestley. 1982. “Stress-strain behavior of concrete confined by overlapping hoops at low and high strain rates.” ACI J. 79 (1): 13–27.
Scott, M. H., and G. L. Fenves. 2006. “Plastic hinge integration methods for force-based beam-column elements.” J. Struct. Eng. 132 (2): 244–252. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:2(244).
Sheikh, S. A., and S. M. Uzumeri. 1980. “Strength and ductility of tied concrete columns.” J. Struct. Div. 106 (5): 1079–1102.
Sheikh, S. A., and S. M. Uzumeri. 1982. “Analytical model for concrete confinement in tied columns.” J. Struct. Div. 108 (12): 2703–2722.
Sideris, P., and M. Salehi. 2016. “A gradient inelastic flexibility-based frame element formulation.” J. Eng. Mech. 142 (7): 04016039. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001083.
Soesianawati, M. T., R. Park, and M. J. N. Priestley. 1986. “Limited ductility design of reinforced concrete columns.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
Spacone, E., F. C. Filippou, and F. F. Taucer. 1996a. “Fibre beam-column model for non-linear analysis of R/C frames. Part I: Formulation.” Earthquake Eng. Struct. Dyn. 25 (7): 711–725. https://doi.org/10.1002/(SICI)1096-9845(199607)25:7%3C711::AID-EQE576%3E3.0.CO;2-9.
Spacone, E., F. C. Filippou, and F. F. Taucer. 1996b. “Fibre beam-column model for non-linear analysis of R/C frames. Part II: Applications.” Earthquake Eng. Struct. Dyn. 25 (7): 727–742. https://doi.org/10.1002/(SICI)1096-9845(199607)25:7%3C727::AID-EQE577%3E3.0.CO;2-O.
Strömberg, L., and M. Ristinmaa. 1996. “FE-formulation of a nonlocal plasticity theory.” Comput. Methods Appl. Mech. Eng. 136 (1–2): 127–144. https://doi.org/10.1016/0045-7825(96)00997-8.
Tanaka, H., and R. Park. 1990. “Effect of lateral confining reinforcement on the ductile behaviour of reinforced concrete columns.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
Valipour, H. R., and S. J. Foster. 2009. “Nonlocal damage formulation for a flexibility-based frame element.” J. Struct. Eng. 135 (10): 1213–1221. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000054.
Van Mier, J. G. M. 1984. “Strain-softening of concrete under multiaxial loading conditions.” Ph.D. thesis, Eindhoven Univ. of Technology.
Van Mier, J. G. M., S. P. Shah, M. Arnaud, J. P. Balayssac, A. Bascoul, S. Choi, D. Dasenbrock, G. Ferrara, C. French, and M. E. Gobbi. 1997. “Strain-softening of concrete in uniaxial compression.” Mater. Struct. 30 (4): 195–209. https://doi.org/10.1007/BF02486177.
Vonk, R. A. 1993. A micromechanical investigation of solftening of concrete loaded in compression. Eindhoven, Netherlands: Eindhoven Univ. of Technology.
Watson, S., and R. Park. 1989. “Design of reinforced concrete frames of limited ductility.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
Zahn, F. A., R. Park, and M. J. N. Priestley. 1985. “Design of reinforced concrete bridge columns for strength and ductility.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
Zhang, G., and K. Khandelwal. 2016. “Modeling of nonlocal damage-plasticity in beams using isogeometric analysis.” Comput. Struct. 165: 76–95. https://doi.org/10.1016/j.compstruc.2015.12.006.
Zienkiewicz, O. C., and R. L. Taylor. 2005. The finite element method for solid and structural mechanics. Oxford, UK: Butterworth-Heinemann.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Nov 15, 2017
Accepted: Jun 5, 2018
Published online: Sep 26, 2018
Published in print: Dec 1, 2018
Discussion open until: Feb 26, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.