Experimental Evaluation of Steel-Plate Composite Walls Subject to Blast Loads
Publication: Journal of Structural Engineering
Volume 144, Issue 9
Abstract
Steel-plate composite (SC) walls consist of a concrete infill sandwiched between two steel faceplates. The faceplates are anchored to the concrete using stud anchors or ties, and connected to each other using steel tie bars. This type of sandwich composite construction has the potential for excellent blast resistance because the steel faceplates provide confinement to the concrete and prevent concrete scabbing and spalling. This paper presents the results of an experimental investigation conducted to evaluate the blast resistance of small-scale SC wall panel specimens by subjecting them to short-duration uniform pressure loads in a blast load simulator facility. All the panel specimens had the same global dimensions (length = 1,626 mm, width = 279 mm, and thickness = 102 mm) but varied certain design parameters: (1) the faceplate reinforcement ratio ( faceplate thickness/wall thickness = 3.5–5.6%), (2) faceplate slenderness ratio ( = stud anchor spacing/plate thickness = 18–29), (3) faceplate yield strength (), and (4) tie reinforcement ratio ( = area of tie bar/square of tie spacing = 0.37–1.23%). The blast load peak reflected pressures varied from 130 to 425 kPa, and the corresponding reflected impulses varied from 1,790 to . This paper summarizes the experimental results including (1) the dynamic displacement history at two locations, (2) acceleration history at midspan, and (3) strain histories at several locations on the steel faceplates. The reflected pressures were also recorded, and high-speed videography from three directions was used to record the response. Experimental results indicate that the structural responses of all 12 panel specimens included elastic and plastic deformations and were dominated by flexural behavior. Experimental results were compared with analytical results from a single-degree-of-freedom (SDOF) model. The SDOF model estimated displacements on average 10% larger than measured, indicating that one-way behavior of SC walls subjected to short-duration uniform pressure loads is reasonably estimated using fundamental bending mechanics.
Get full access to this article
View all available purchase options and get full access to this article.
References
AISC. 2015. Specification for safety-related steel structures for nuclear facilities including Supplement No. 1. ANSI/AISC N690s1-15. Chicago: AISC.
ASTM. 2017. Standard specification for steel, sheet and strip, hot-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, and ultra-high strength. ASTM A1011. West Conshohocken, PA: ASTM.
Bhardwaj, S. R., and A. H. Varma. 2017. Design of modular steel-plate composite walls for safety-related nuclear facilities: AISC design guide 32. Chicago: AISC.
Bruhl, J. C. 2015. “Behavior and design of steel-plate composite (SC) walls for blast loads.” Ph.D. dissertation, Dept. of Civil Engineering, Purdue Univ.
Bruhl, J. C., and A. H. Varma. 2017. “Experimental resistance and available ductility of steel-plate composite walls in one-way bending.” J. Struct. Eng. 143 (4): 04016222. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001714.
Bruhl, J. C., A. H. Varma, and W. H. Johnson. 2015. “Design of composite SC walls to prevent perforation from missile impact.” Int. J. Impact Eng. 75 (Jan): 75–87. https://doi.org/10.1016/j.ijimpeng.2014.07.015.
Chopra, A. K. 2001. Dynamics of structures: Theory and applications to earthquake engineering. Upper Saddle River, NJ: Prentice Hall.
Coyle, N., and D. Cormie. 2009. “Design of elements in steel-concrete-steel composite materials.” In Blast effects on buildings, edited by D. Cormie, G. Mays, and P. Smith, 154–176. London: Thomas Telford.
DOE (US Department of Energy). 2006. Accident analysis for aircraft crash into hazardous facilities. Washington, DC: DOE.
DOE (US Department of Energy). 2010. Nuclear energy enabling technologies workshop report. Rockville, MD: DOE.
Grisaro, H., and A. Dancygier. 2014. “Assessment of the perforation limit of a composite RC barrier with a rear steel liner to impact of a non-deforming projectile.” Int. J. Impact Eng. 64 (Feb): 122–136. https://doi.org/10.1016/j.ijimpeng.2013.10.002.
Heng, L., L. J. Kennedy, and G. C. Mays. 1995. “Blast resistance of fully enclosed steel-concrete-steel sandwich panels.” In Proc., 7th Int. Symp. on Interaction of the Effects of Munitions with Structures, 189–197. Mannheim, Germany.
Hulton, F. G. 1995. “The behaviour of steel-backed reinforced concrete panels under explosive attack.” In Proc., 7th Int. Symp. on Interaction of the Effects of Munitions with Structures, 111–116. Mannheim, Germany.
Hulton, F. G., and M. S. Gough. 1999. “The development of steel-plate/reinforced concrete composite panels to resist explosive attack.” In Proc., 9th Int. Symp. on Interaction of the Effects of Munitions with Structures, 63–69. Mannheim, Germany.
Johnson, C. F. 2013. “Concrete masonry wall retrofit systems for blast protection.” Ph.D. dissertation, Dept. of Civil Engineering, Texas A&M Univ.
Lan, S., T.-S. Lok, and L. Heng. 2005. “Composite structural panels subjected to explosive loading.” Constr. Build. Mater. 19 (5): 387–395. https://doi.org/10.1016/j.conbuildmat.2004.07.021.
Liew, J. Y. R., and T. Y. Wang. 2011. “Novel steel-concrete-steel sandwich composite plates subject to impact and blast load.” Adv. Struct. Eng. 14 (4): 673–687. https://doi.org/10.1260/1369-4332.14.4.673.
Mizuno, J., H. Morikawa, N. Koshika, K. Wakimoto, K. Kobayashi, and R. Fukuda. 2005. “Investigation on impact resistance of steel plate reinforced concrete barriers against aircraft impact. Part 2: Simulation analyses of scale model impact tests.” In Proc., 18th Int. Conf. on Structure Mechanics in Reactor Technology (SMiRT-18), 2580–2590. Charlotte, NC: IASMIRT.
Nuclear Energy Institute. 2011. Methodology for performing aircraft impact assessments for new plant designs. Walnut Creek, CA: ERIN Engineering & Research.
Piore, A. 2011. “Planning for the black swan.” Sci. Am. Mag. 304 (6): 48–53. https://doi.org/10.1038/scientificamerican0611-48.
Schlaseman, C. 2004. Application of advanced construction technologies to new nuclear power plants. Washington, DC: US Dept. of Energy.
US Department of Defense. 2008. Structures to resist the effects of accidental explosions. Washington, DC: US Dept. of Defense.
Varma, A. H., S. R. Malushte, and Z. Lai. 2015. “Modularity & innovation using steel-plate composite (SC) walls for nuclear and commercial construction.” In Proc., 11th Int. Conf. on Advances in Steel-Concrete Composite Structures, 565–571. West Yorkshire, UK: ASCCS.
Varma, A. H., S. R. Malushte, K. C. Sener, and Z. Lai. 2014. “Steel-plate composite (SC) walls for safety related nuclear facilities: Design for in-plane forces and out-of-plane moments.” Nucl. Eng. Des. 269 (Apr): 240–249. https://doi.org/10.1016/j.nucengdes.2013.09.019.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jun 1, 2017
Accepted: Apr 4, 2018
Published online: Jul 3, 2018
Published in print: Sep 1, 2018
Discussion open until: Dec 3, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.