Fatigue Assessment of Fiber-Reinforced Concrete Using 1,200-mm Diameter Round Panels
Publication: Journal of Structural Engineering
Volume 144, Issue 6
Abstract
The fatigue performance of concrete in response to high-cycle repetitive loading is important for concrete road pavements and other concrete elements such as railway sleepers, offshore structures, and wind turbines subject to repetitive cyclic loading. Unfortunately, fatigue tests on concrete typically produce highly variable results that make it difficult to discern trends in behavior or assess the influence of selected parameters on cyclic load resistance. The majority of published fatigue performance assessments have been conducted using simply supported beams, but these result in highly variable and unreliable results. In this investigation, round panels of 1,200 mm (47 in.) diameter have been examined as a means of more reliably assessing the fatigue resistance of concrete. Cyclic tests on round concrete panels allow some redistribution of stress over relatively large cracked sections during the propagation of cracks, and thereby appear to facilitate the assessment of fatigue performance for plain and fiber-reinforced concrete with an improved degree of repeatability. Extensive data sets have indicated a standard error of approximately 4% for cyclic load resistance compared to an error at least twice this magnitude for beams.
Get full access to this article
View all available purchase options and get full access to this article.
References
Al Jabbari, Y. S., Mparmpagadaki, M., Zinelis, S., and Eliades, G. (2012). “Assessment of fatigue parameters of dental resin composites using dynamic fatigue testing.” J. Compos. Mater., 47(4), 419–424.
ASTM. (1996). “Standard test method for biaxial flexure strength (modulus of rupture) of ceramic substrates.” ASTM F394, West Conshohocken, PA.
ASTM. (2012a). “Standard test method for flexural toughness of fiber reinforced concrete (using centrally loaded panel).” ASTM C1550, West Conshohocken, PA.
ASTM. (2012b). “Standard test method for flexural toughness of fiber-reinforced concrete (using beam with third-point loading).” ASTM C1609/C1609M, West Conshohoken, PA.
Barr, B. I. G., et al. (2003). “Round-robin analysis of the RILEM TC 162-TDF beam-bending test. Part 1: Test method evaluation.” Mater. Struct., 36(9), 609–620.
Bernard, E. S. (2002). “Correlations in the behaviour of fibre reinforced shotcrete beam and panel specimens.” Mater. Struct., 35(247), 156–164.
Bernard, E. S. (2013). “Development of a 1200 mm diameter round panel test for post-crack assessment of fiber reinforced concrete.” Adv. Civ. Eng. Mater., 2(1), 457–471.
Bernard, E. S. (2016). “Post crack performance of fibre reinforced concrete and its effect on the apparent cracking load of slabs.” Aust. J. Struct. Eng., 17(2), 1–10.
Bernard, E. S., and Reid, S. G. (2016). “Fatigue assessment of fibre reinforced concrete using 1200 mm diameter round panels.”, Technologies in Structural Engineering, Sydney, Australia.
Cavalaro, S. H. P., and Aguado, A. (2015). “Intrinsic scatter of FRC: An alternative philosophy to estimate characteristic values.” Mater. Struct., 48(11), 3537–3555.
Clemmer, H. F. (1922). “Fatigue of concrete.” ASTM, Philadelphia, PA.
Darter, M. I. (1990). “Concrete slab vs beam fatigue models.” Proc., 2nd Int. Workshop on the Theoretical Design of Concrete Pavements, Sigüenza, Spain, 472–481.
De With, G., and Wagemans, H. H. M. (1989). “Ball-on-ring test revisited.” J. Am. Ceram. Soc., 72(8), 1538–1541.
Mills, R. E., and Dawson, R. F. (1927). “Fatigue of concrete.” Proc., 7th Annual Meeting of the Highway Research Board, Vol. 7, Highway Research Board, Washington, DC, 160–172.
Moss, J. (2008). “Pavement flexural fatigue capacity and the influence of mix charging sequence.” 9th Int. Conf. on Concrete Pavements, ISCP, San Francisco.
Murdock, J. W. (1957). “A critical review of research on fatigue of plain concrete.”, Univ. of Illinois Engineering Experimental Station, Champaign, IL.
Murdock, J. W., and Kelser, C. E. (1959). “Effect of range of stress on the fatigue strength of plain concrete beams.” ACI J. Proc., 55(2), 221–232.
Oh, B. H. (1991). “Fatigue-life distributions of concete for various stress levels.” ACI Mater. J., 88(2), 122–128.
Planas, J., and Elices, M. (2002). “Drying shrinkage effect on the modulus of rupture.” Creep and shrinkage of concrete, Z. P. Bazant and I. Carol, eds., E&FN Spon, London, 357–368.
Raithby, R. D., and Galloway, J. W. (1974). “Effects of moisture condition, age, and rate of loading on fatigue of plain concrete.” Fatigue of concrete, American Concrete Institute, Farmington Hills, MI, 15–34.
RMS (Roads and Maritime Services). (2015). “QA specification R83.” Concrete pavement base, Roads and Maritime Service, Sydney, NSW, Australia.
Shi, X. P., Fwa, T. F., and Tan, S. A. (1993). “Flexural fatigue strength of plain concrete.” ACI Mater. J., 90(5), 435–440.
Singh, S. P., and Kaushik, S. K. (2001). “Flexural fatigue analysis of steel fiber-reinforced concrete.” ACI Mater. J., 98(4), 306–312.
Singh, S. P., Mohammadi, Y., and Kaushik, S. K. (2005). “Flexural fatigue analysis of steel fibrous concrete containing mixed fibers.” ACI Mater. J., 102(6), 438–444.
Standards Australia. (2010). “General purpose and blended cements.” AS3972, Sydney, NSW, Australia.
Standards Australia. (2014). “Test methods for concrete.” AS1012, Sydney, NSW, Australia.
Standards Australia. (2016). “Supplementary cementitious materials.” AS3582, Sydney, NSW, Australia.
Subramaniam, K. V., O’Neil, E., Popovics, J. S., and Shah, S. P. (2000). “Flexural fatigue of concrete: Experiments and theoretical model.” J. Eng. Mech., 891–898.
Tepfers, R. (1979). “Tensile fatigue strength of plain concrete.” ACI J., 76(8), 919–933.
Tepfers, R., and Kutti, T. (1979). “Fatigue strength of plain, ordinary, and lightweight concrete.” ACI J. Proc., 76(2), 635–652.
Vanderwalle, L., Van Rickstal, F., Heirman, G., and Parmentier, B. (2008). “The round panel test and the 3-point bending test.” Proc., 7th Int. RILEM Symp. on Fibre Reinforced Concrete, R. Gettu, ed., RILEM, Paris.
Walpole, R. E., Myers, R. H., Myers, S. L., and Ye, K. (2012). Probability & statistics for engineers & scientists, 9th Ed., Prentice Hall, Boston.
Wirsching, P. H., and Yao, J. T. P. (1970). “Statistical methods in structural fatigue.” J. Struct. Div., 96(6), 1201–1219.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Aug 6, 2017
Accepted: Dec 7, 2017
Published online: Apr 6, 2018
Published in print: Jun 1, 2018
Discussion open until: Sep 6, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.