Local Buckling of Welded Box Beams Made of Ultrahigh-Strength Steels
Publication: Journal of Structural Engineering
Volume 144, Issue 7
Abstract
Laboratory tests have shown that current standardized design rules lead to overly optimistic results for calculated ultimate loads of plated structures, especially for internal elements such as box beams. Additionally, the validity of applying equations to compute local buckling resistance might be restricted to steel grades for which the yield strength is less than 500–700 MPa. Both the literature survey and recent experimental buckling tests using ultrahigh-strength steel (UHSS) show that the current design equations can be extended to at least a nominal yield strength of 1,000 MPa. Additionally, a new simplified equation for the reduction factor is proposed and a statistical calculation is presented to compare current and proposed calculation methods.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study has been partially funded by the Finnish Funding Agency for Technology and Innovation and Ruukki as part of the research program, Advanced Metals Technology—New Products. The authors also thank Mr. Jouko Kouhi from the Finnish Constructional Steelwork Association for his technical assistance.
References
AISI (American Iron and Steel Institute). 1986. Cold-formed steel design manual, part I: Specification. New York: W.P. Reyman Associates.
ASTM. 1967. Specification for steel for bridges and building. ASTM A7. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard specification for high-yield-strength, quenched and tempered alloy steel plate, suitable for welding. ASTM A514. West Conshohocken, PA: ASTM.
CEN (European Committee for Standardization). 2002. Basis of structural design. EN 1990. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2004. Design of steel structures, part 1.5: Plated structural elements. Eurocode 3. Brussels, Belgium: CEN.
Clarin, M. 2004. High strength steel: Local buckling and residual stresses. Luleå, Sweden: Luleå Univ. of Technology.
Huusko, L. 2006. “Local buckling of ultra high strength steels—Extending the strength parameter validity limits.” [In Finnish.] M.S. thesis, Dept. of Mechanical Engineering, Lappeenranta Univ. of Technology.
McDermott, J. F. 1969. “Local plastic buckling of A514 steel members.” J. Struct. Div. 95 (ST9): 1837–1850.
Möller, M. 1995. On inelastic local flange buckling. Luleå, Sweden: Luleå Univ. of Technology.
Möller, M., and B. Johansson. 1995. Buckling of rectangular plates made of two different types of Weldox 1100 steel. Luleå, Sweden: Luleå Univ. of Technology.
Nilsson, M. 1998. Local buckling of flanges in high strength steel. Luleå, Sweden: Luleå Univ. of Technology.
Nishino, F., Y. Ueda, and L. Tall. 1967. Experimental investigation of the buckling of plates with residual stresses. 12–30. West Conshohocken, PA: ASTM.
Okumura, T., F. Nishino, and A. Hasegawa 1972. “Local buckling strength of box section columns.” [In Chinese.] Proc. Jpn. Soc. Civ. Eng. 1972 (205): 19–30.
Rasmussen, K., and G. Hancock. 1995. “Tests of high strength steel columns.” J. Constr. Steel Res. 34 (1): 17–52.
Sakino, K., H. Nakahara, S. Morino, and I. Nishiyama. 2004. “Behavior of centrally loaded concrete-filled steel-tube short columns.” J. Struct. Eng. 130 (2): 180–188.
Schillo, N., and M. Feldmann. 2015. “Local buckling behavior of welded box sections made of high-strength steel: Comparing experiments with EC3 and general method.” Steel Constr. Design Res. 8 (3): 179–186.
Völling, B., G. Sedlacek, D. Pak, and M. Clarin. 2006. “Zum Beulverhalten kaltgeformter und geschweisster Rechteckhohlprofile aus hochfestem Stahl” [For buckling behavior of cold formed and welded rectangular hollow sections made of high strength steel]. [In German.] Stahlbau 75 (11): 889–896.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Nov 24, 2016
Accepted: Nov 27, 2017
Published online: Apr 21, 2018
Published in print: Jul 1, 2018
Discussion open until: Sep 21, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.