Numerical Study of Bond and Development of Column Longitudinal Reinforcement Extended into Oversized Pile Shafts
Publication: Journal of Structural Engineering
Volume 144, Issue 5
Abstract
This paper presents a numerical investigation to examine the bond-slip behavior of column longitudinal reinforcing bars embedded in oversized pile shafts and to determine the minimum embedment length required for the column bars to prevent anchorage failure. Three-dimensional nonlinear finite-element models of column-pile assemblies incorporating the bond-slip behavior of the longitudinal reinforcing bars have been developed for the numerical analyses. The capability of the models in capturing the response of column bars along their embedment length has been verified with experimental results from four full-scale column-pile assemblies tested under cyclic lateral loads. The study has shown that the bond-stress distribution along the bar anchorage length is highly nonuniform and that the embedment length specified for the column reinforcement in current design standards is very conservative. A new design formula that significantly reduces the embedment length has been evaluated. The numerical results have indicated that the new embedment-length formula provides a good margin of safety against the pull-out failure of the column bars. The results have also shown that the use of an engineered steel casing to provide lateral confinement for the pile is an effective means to enhance the bond strength and reduce the slip of the column longitudinal bars in the anchorage region.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for the research presented in this paper was provided by the California Department of Transportation (Caltrans) under Contract No. 59A0710. The authors appreciate the technical input provided by Caltrans engineers throughout this study. However, the opinions expressed in this paper are those of the authors and do not necessarily reflect those of the sponsor.
References
AASHTO. (2010). LRFD bridge design specifications, 5th Ed., Washington, DC.
AASHTO. (2011). Seismic bridge design specifications, 2nd Ed., Washington, DC.
Abaqus version 6.10 [Computer software]. Dassault Systemes Simulia, Providence, RI.
ASTM. (2009). “Standard specification for low-alloy steel deformed and plain bars for concrete reinforcement.” ASTM A706/A706M-09b, West Conshohocken, PA.
Caltrans (California Department of Transportation). (2010). Caltrans seismic design criteria, version 1.6, Sacramento, CA.
Karthik, M. M., and Mander, J. B. (2011). “Stress-block parameters for unconfined and confined concrete based on a unified stress-strain model.” J. Struct. Eng., 270–273.
Lee, J., and Fenves, G. L. (1998). “Plastic-damage model for cyclic loading of concrete structures.” J. Eng. Mech., 892–900.
Lubliner, J., Oliver, J., Oller, S., and Oñate, E. (1989). “A plastic-damage model for concrete.” Int. J. Solids Struct., 25(3), 299–326.
McLean, D. I., and Smith, C. L. (1997). “Noncontact lap splice in bridge column-shaft connections.”, Washington State Transportation Center, Washington State Univ., Pullman, WA.
Moharrami, M., and Koutromanos, I. (2016). “Triaxial constitutive model for concrete under cyclic loading.” J. Struct. Eng., 04016039.
Murcia-Delso, J., Liu, Y., and Shing, P. B. (2016). “Development of bridge column longitudinal reinforcement in oversized pile shafts.” J. Struct. Eng., 04016114.
Murcia-Delso, J., and Shing, P. B. (2015). “Bond-slip model for detailed finite element analysis of reinforced concrete structures.” J. Struct. Eng., 04014125.
Murcia-Delso, J., Shing, P. B., Stavridis, A., and Liu, Y. (2013). “Required embedment length of column reinforcement extended into type II shafts.”, Structural Systems Research Project, Dept. of Structural Engineering, Univ. of California, San Diego.
Murcia-Delso, J., Stavridis, A., and Shing, P. B. (2015). “Tension development length of large-diameter bars for severe cyclic loading.” ACI Struct. J., 112(6), 689–700.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Dec 1, 2016
Accepted: Oct 28, 2017
Published online: Feb 16, 2018
Published in print: May 1, 2018
Discussion open until: Jul 16, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.