Crack Model for RC Members Based on Compatibility of Stress-Transfer and Mean-Strain Approaches
Publication: Journal of Structural Engineering
Volume 143, Issue 9
Abstract
The current study proposes a simple and mechanically sound analytical approach for crack analysis of reinforced concrete (RC) flexural members at the stage of stabilized cracking. The philosophy behind the proposed methodology is to establish mean spacing between the primary cracks through the compatibility of the stress transfer and mean strain approaches. The governing parameters of crack spacing are obtained by equating mean strains of the tension reinforcement defined by these approaches. The model assumes that a single RC block of a length of mean crack spacing represents the averaged deformation behavior of the cracked member. Based on the experimental evidence, reinforcement strain within the block is characterized by a strain profile consisting of straight lines representing zones with different bond characteristics. It was shown that crack spacing is mostly governed by four geometrical parameters given in the order of significance: section height, reinforcement ratio, bar diameter, and cover. A limited comparative analysis has demonstrated that the predictions of mean crack spacing by the proposed model agree well with the tests. Considerations are given to extend the proposed methodology to the analysis of maximum crack width.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The author gratefully acknowledges the financial support provided by the Research Council of Lithuania (Research Project MIP-093/2015).
References
21st Century Tech Blog. (2016). “Concrete and climate change—The greening of infrastructure.” ⟨http://www.21stcentech.com/concrete-climate-change-greening-infrastructure/⟩ (Dec. 5, 2016).
Beeby, A. W. (1970). “An investigation of cracking in slabs spanning one way.”, Cement and Concrete Association, London.
Beeby, A. W. (2004). “The influence of the parameter on crack widths.” Struct. Concr., 5(2), 71–83.
Borosnyói, A., and Balázs, G. L. (2005). “Models for flexural cracking in concrete: The state of the art.” Struct. Concr., 6(2), 53–62.
Broms, B. B. (1965). “Crack width and crack spacing in reinforced concrete members.” ACI J., 62(10), 1237–1256.
Calderón, B. E. (2008). “Estudio experimental de la fisuración en piezas de hormigón armado sometidas a flexión pura.” Ph.D. thesis, Universidad Politécnica de Madrid, Madrid, Spain.
CEN (European Committee for Standardization). (2004). “Design of concrete structures: Part 1-1: General rules and rules for buildings.” Eurocode 2, Brussels, Belgium.
fib (International Federation for Structural Concrete). (2013). Model code for concrete structures 2010, Wiley, Berlin, 434.
Gergely, P., and Lutz, L. A. (1968). Maximum crack width in reinforced concrete flexural members. Causes, mechanism, and control of cracking in concrete, American Concrete Institute, Detroit, 87–117.
Ghali, A., Favre, R., and Elbadry, M. (1986). Concrete structures: Stresses and deformations: Analysis and design for serviceability, Chapman & Hall, London.
Gilbert, R. I. (2008). “Control of flexural cracking in reinforced concrete.” ACI Struct. J., 105(3), 301–307.
Gilbert, R. I., and Nejadi, S. (2004). An experimental study of flexural cracking in reinforced concrete members under short term loads, Univ. of New South Wales, School of Civil and Environmental Engineering, Sydney, Australia.
Goto, Y. (1971). “Cracks formed in concrete around deformed tension bars.” ACI J., 68(4), 244–251.
Gribniak, V., Pérez Caldentey, A., Kaklauskas, G., Rimkus, A., and Sokolov, A. (2016). “Effect of arrangement of tensile reinforcement on flexural stiffness and cracking.” Eng. Struct., 124(1), 418–428.
Henault, J. M., et al. (2012). “Quantitative strain measurement and crack detection in RC structures using a truly distributed fiber optic sensing system.” Constr. Build. Mater., 37, 916–923.
Houde, J. (1974). “Study of force-displacement relationships for the finite-element analysis of reinforced concrete.” Ph.D. thesis, McGill Univ., Montreal.
Ichinose, T., Kanayama, Y., Inoue, Y., and Bolander, J. E. (2004). “Size effect on bond strength of deformed bars.” Constr. Build. Mater., 18(7), 549–558.
Kaklauskas, G., et al. (2016a). “Experimental investigation on strain distribution in reinforcement of RC specimens under tension loading.” Proc., Int. RILEM Conf. on Materials, Systems and Structures in Civil Engineering, Rilem Publications, Paris, 279–286.
Kaklauskas, G., and Ghaboussi, J. (2001). “Stress-strain relations for cracked tensile concrete from RC beam tests.” J. Struct. Eng., 64–73.
Kaklauskas, G., and Gribniak, V. (2011). “Eliminating shrinkage effect from moment-curvature and tension-stiffening relationships of reinforced concrete members.” J. Struct. Eng., 1460–1469.
Kaklauskas, G., and Gribniak, V. (2016). “Hybrid tension stiffening approach for decoupling shrinkage effect in cracked reinforced concrete members.” J. Eng. Mech., 04016085.
Kaklauskas, G., Ramanauskas, R., Ng, P. L., Jakubovskis, R., and Juknys, M. (2016b). “Crack spacing model for reinforced concrete tension members based on damage zone and strain compliance concepts.” Proc., FIB Symp. on Performance-Based Approaches for Concrete Structures, federation international du beton (fib), Lausanne, Switzerland.
Kankam, C. K. (1997). “Relationship of bond stress, steel stress, and slip in reinforced concrete.” J. Struct. Eng., 79–85.
Kenel, A., Nellen, P., Frank, A., and Marti, P. (2005). “Reinforcing steel strains measured by Bragg grating sensors.” J. Mater. Civ. Eng., 423–431.
Marti, P., Alvarez, M., Kaufmann, W., and Sigrist, V. (1998). “Tension chord model for structural concrete.” Struct. Eng. Int., 8(4), 287–298.
Murray, A., Castel, A., Gilbert, R. I., and Chang, Z. T. (2016). “Time-dependent changes in the instantaneous stiffness of reinforced concrete beams.” Eng. Struct., 126, 641–651.
Perez, C. A., Corres, P. H., Peset, I. J., and Giraldo, S. A. (2013). “Cracking of RC members revisited: Influence of cover, φ/ρs, ef and stirrup spacing—An experimental and theoretical study.” Struct. Concr., 14(1), 69–78.
Reineck, K. (1991). “Ultimate shear force of structural concrete members without transverse reinforcement derived from a mechanical model.” ACI Struct. J., 88(5), 592–602.
Ruiz, M. F., Muttoni, A., and Gambarova, P. G. (2007). “Analytical modeling of the pre- and postyield behavior of bond in reinforced concrete.” J. Struct. Eng., 1364–1372.
Rüsch, H., and Rehm, G. (1964). “Versuche mit Betonformstahlen, Deutscher Ausschuss fur Stahlbcton.” Berlin.
Saliger, R. (1936). “High grade steel in reinforced concrete.” Proc., 2nd Congress of Int. Association for Bridge and Structural Engineering, Vol. 2, IABSE Publications, Berlin, 293–315.
Scott, R. H., and Gill, P. A. T. (1987). “Short-term distributions of strain and bond stress along tension reinforcement.” Struct. Eng., 65(2), 39–43.
Wu, H. Q., and Gilbert, R. I. (2009). “Modeling short-term tension stiffening in reinforced concrete prisms using a continuum-based finite element model.” Eng. Struct., 31(10), 2380–2391.
Zabihi, N., and Eren, O. (2014). “Compressive strength conversion factors of concrete as affected by specimen shape and size.” Res. J. Appl. Sci., Eng. Tech., 7(20), 4251–4257.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 143 • Issue 9 • September 2017
Copyright
©2017 American Society of Civil Engineers.
History
Received: Aug 9, 2016
Accepted: Mar 7, 2017
Published online: Jun 8, 2017
Published in print: Sep 1, 2017
Discussion open until: Nov 8, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.