Concrete-Filled Circular Steel Tubes with a Timber Infill under Axial Compression
Publication: Journal of Structural Engineering
Volume 143, Issue 7
Abstract
Over the past two decades, there has been significant interest in research relating to concrete-filled tubes, and a corresponding penetration of this technology into practice. This paper aims to expound upon the effect of timber cores on the structural response of concrete-filled circular tubes under compression. A timber infill with different shapes and geometries surrounded by concrete and encased in a steel tube was employed. The effects of the combination of infill elements on the failure, axial capacity, ductility, and structural efficiency (weight versus capacity) are exhaustively set forth. For the specimens with the highest timber to concrete ratio, the capacity was enhanced by about two times the capacity of the hollow steel specimens. For these specimens a significant reduction in the total weight of the composite element was obtained relative to the fully concrete-filled specimens. These specimens showed the highest ductility among the other specimens. In addition, greater ratios of energy absorption to the mass were obtained for the specimens with different timber cores in comparison to the equivalent values for fully concrete-filled tubes, which is quite desirable in many practical scenarios. It is found that the use of timber as an inner core element in this new composite yields promising results in decreasing the weight and yet enhancing the capacity, ductility, and energy absorption, and can be a good alternative to double-skin concrete-filled steel tubes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank the School of Engineering and ICT of the University of Tasmania for their support rendered throughout the project.
References
Australian Standard. (1993). “Methods of testing concrete.”, Sydney.
Australian Standard. (2009). “Concrete structures.”, Sydney.
Australian Standard. (2010). “Timber structures—Part 1: Design methods.”, Sydney.
Chitawadagi, M. V., Narasimhan, M. C., and Kulkarni, S. (2010). “Axial strength of circular concrete-filled steel tube columns—DOE approach.” J. Construct. Steel Res., 66(10), 1248–1260.
Dundu, M. (2012). “Compressive strength of circular concrete filled steel tube columns.” Thin-Walled Struct., 56, 62–70.
Ghanbari Ghazijahani, T., Jiao, H., and Holloway, D. (2015a). “Rectangular steel tubes with timber infill and CFRP confinement under compression: Experiments.” J. Construct. Steel Res., 114, 196–203.
Ghanbari Ghazijahani, T., Jiao, H., and Holloway, D. (2015b). “Structural behavior of shells with different cutouts under compression: An experimental study.” J. Construct. Steel Res., 105, 129–137.
Ghanbari Ghazijahani, T., Jiao, H., and Holloway, D. (2015c). “Timber filled CFRP jacketed circular steel tubes under axial compression.” Construct. Build. Mater., 94, 791–799.
Han, L.-H., Li, Y.-J., and Liao, F.-Y. (2011a). “Concrete-filled double skin steel tubular (CFDST) columns subjected to long-term sustained loading.” Thin-Walled Struct., 49(12), 1534–1543.
Han, L.-H., Ren, Q.-X., and Li, W. (2011b). “Tests on stub stainless steel-concrete–carbon steel double-skin tubular (DST) columns.” J. Construct. Steel Res., 67(3), 437–452.
Huang, H., Han, L.-H., Tao, Z., and Zhao, X.-L. (2010). “Analytical behaviour of concrete-filled double skin steel tubular (CFDST) stub columns.” J. Construct. Steel Res., 66(4), 542–555.
Kwon, Y. B., and Jeong, I. K. (2014). “Resistance of rectangular concrete-filled tubular (CFT) sections to the axial load and combined axial compression and bending.” Thin-Walled Struct., 79, 178–186.
Kwon, Y. B., Seo, S. J., and Kang, D. W. (2011). “Prediction of the squash loads of concrete-filled tubular section columns with local buckling.” Thin-Walled Struct., 49(1), 85–93.
Li, W., Han, L.-H., and Zhao, X.-L. (2012a). “Axial strength of concrete-filled double skin steel tubular (CFDST) columns with preload on steel tubes.” Thin-Walled Struct., 56, 9–20.
Li, W., Ren, Q.-X., Han, L.-H., and Zhao, X.-L. (2012b). “Behaviour of tapered concrete-filled double skin steel tubular (CFDST) stub columns.” Thin-Walled Struct., 57, 37–48.
Tao, Z., Uy, B., Liao, F.-Y., and Han, L.-H. (2011). “Nonlinear analysis of concrete-filled square stainless steel stub columns under axial compression.” J. Construct. Steel Res., 67(11), 1719–1732.
Teng, J., Yu, T., Wong, Y., and Dong, S. (2007). “Hybrid FRP-concrete–steel tubular columns: Concept and behavior.” Construct. Build. Mater., 21(4), 846–854.
Uenaka, K., Kitoh, H., and Sonoda, K. (2010). “Concrete filled double skin circular stub columns under compression.” Thin-Walled Struct., 48(1), 19–24.
Yan, L., and Chouw, N. (2013). “Crashworthiness characteristics of flax fibre reinforced epoxy tubes for energy absorption application.” Mater. Des., 51, 629–640.
Yang, Y., and Han, L. (2012). “Concrete filled steel tube (CFST) columns subjected to concentrically partial compression.” Thin-Walled Struct., 50(1), 147–156.
Yang, Y.-F., and Han, L.-H. (2011). “Behaviour of concrete filled steel tubular (CFST) stub columns under eccentric partial compression.” Thin-Walled Struct., 49(2), 379–395.
Yang, Y.-F., Han, L.-H., and Sun, B.-H. (2012). “Experimental behaviour of partially loaded concrete filled double-skin steel tube (CFDST) sections.” J. Construct. Steel Res., 71, 63–73.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Oct 30, 2015
Accepted: Nov 18, 2016
Published online: Mar 1, 2017
Published in print: Jul 1, 2017
Discussion open until: Aug 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.