Development and Evaluation of Seismic Retrofit Alternatives for Older Concentrically Braced Frames
Publication: Journal of Structural Engineering
Volume 143, Issue 5
Abstract
Concentrically braced frames (CBFs) have been used for seismic-lateral-force resisting systems for many years, but prior to approximately 1988, they were not designed to promote ductile response using capacity-based design. These older, nonductile CBFs (NCBFs) have been investigated in prior research that identified severe deficiencies in these systems, but some deficiencies had more detrimental consequences than others. This paper describes a research study to evaluate retrofit strategies for NCBFs. Welded and bolted continuous and split shear-plate connections, end-plate connections, split double-angle connections, and integrated gusset-shear plate connections were investigated. Retrofit strategies included brace replacement, concrete in-fill of a locally slender brace, weld overlay, bolt reinforcement, development of in-plane brace buckling, and the use of buckling-restrained braces. In all cases, system deformation capacity was enhanced, and the extent of improvement depended on connection configuration, connection demand-to-capacity ratios, and bracing type.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based on work supported by the National Science Foundation (NSF) Network for Earthquake Engineering Simulation under Grant No. CMMI-1208002 and the NSF Graduate Research Fellowship under Grant No. DGE-1256082. Independent financial support and material donations were provided by the American Institute of Steel Construction. In addition, the research team received advice from many practicing consultants. This advice and financial support is greatly appreciated. The tests were performed at the Structural Research Laboratory at the University of Washington, and the authors gratefully acknowledge the students and staff who conducted the tests. Any opinion, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the sponsoring agencies.
References
AISC. (2010a). “Seismic provisions for structural steel buildings.” ANSI/AISC 341-10, Chicago.
AISC. (2010b). “Specification for structural steel buildings.” ANSI/AISC 360-10, Chicago.
AISC. (2010c). “Steel construction manual.” Chicago.
ATC (Applied Technology Council). (1992). “Guidelines for cyclic seismic testing of components of steel structures for buildings.”, Redwood City, CA.
Ballard, R. (2015). “Impact of connection type on system performance of non-seismic concentrically braced frames.” M.S. thesis, Univ. of Washington, Seattle.
Fisher, J. W., Galambos, T. V., Kulak, G. L., and Ravindra, M. K. (1978). “Load and resistance factor design criteria for connectors.” J. Struct. Div., 104(ST9), 1427–1441.
Goel, S. C. (1992). “Cyclic post buckling behavior of steel bracing members.” Stability and ductility of steel structures under cyclic loading, CRC Press, Boca Raton, FL.
Hewitt, C. M., and Thornton, W. A. (2004). “Rationale behind and proper application of the ductility factor for bracing connections subjected to shear and transverse loading.” Eng. J., 41(1), 3–6.
Hsiao, P. C., Lehman, D. E., Berman, J. W., Roeder, C. W., and Powell, J. (2014). “Seismic vulnerability of older braced frames.” J. Perform. Constr. Facil., 108–120.
ICBO (International Conference of Building Officials). (1988). “Uniform building code.” Whittier, CA.
Johnson, M. M. (2014). “Seismic evaluation of bolted connection in non-seismic concentrically braced frames.” M.S. thesis, Univ. of Washington, Seattle.
Lehman, D. E., Roeder, C. W., Herman, D., Johnson, S., and Kotulka, B. (2008). “Improved seismic performance of gusset plate connections.” J. Struct. Eng., 890–901.
Liu, Z., and Goel, S. C. (1988). “Cyclic load behavior of concrete-filled tubular braces.” J. Struct. Eng., 1488–1506.
Lumpkin, E. J. (2009). “Enhanced seismic performance of multi-story special concentrically brace frames using a balanced design procedure.” M.S. thesis, Univ. of Washington, Seattle.
Palmer, K. D., Christopulos, A. S., Lehman, D. E., and Roeder, C. W. (2014). “Experimental evaluation of cyclically loaded, large-scale, planar and 3-d buckling-restrained braced frames.” J. Constr. Steel Res., 101, 415–425.
Palmer, K. D., Roeder, C. W., and Lehman, D. E. (2016). “Connection design recommendations for improved BRBF performance.” Eng. J., 53(1). 29–45.
Richard, R. M. (1986). “Analysis of large brace connection designs for heavy construction.” Proc., AISC National Engineering Conf., AISC, Chicago.
Roeder, C. W., Lumpkin, E. J., and Lehman, D. E. (2011). “A balanced design procedure for special concentrically braced frame connections.” J. Constr. Steel Res., 67(11), 1760–1772.
Sen, A. D., et al. (2016). “Experimental evaluation of the seismic vulnerability of braces and connections in older concentrically braced frames.” J. Struct. Eng., .
Sloat, D. A. (2014). “Evaluation and retrofit of non-capacity designed braced frames.” M.S. thesis, Univ. of Washington, Seattle.
Swatosh, M. A. (2016). “Seismic evaluation and retrofit of concentrically braced frames.” M.S. thesis, Univ. of Washington, Seattle.
Tsai, C. Y., et al. (2013). “Seismic design and hybrid tests of a full-scale three-story concentrically braced frame using in-plane buckling braces.” Earthquake Spectra, 29(3), 1043–1067.
Yam, M. C. H., and Cheng, J. J. R. (2002). “Behavior and design of gusset plate connections in compression.” J. Constr. Steel Res., 58(5–8), 1143–1159.
Information & Authors
Information
Published In
Copyright
©2016 American Society of Civil Engineers.
History
Received: Jun 1, 2016
Accepted: Oct 28, 2016
Published online: Dec 8, 2016
Published in print: May 1, 2017
Discussion open until: May 8, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.