Sidewall Buckling of Equal-Width RHS Truss X-Joints
Publication: Journal of Structural Engineering
Volume 143, Issue 2
Abstract
This paper presents a new design methodology for equal-width rectangular hollow section (RHS) X-joints failing by sidewall buckling. In the new approach, a slenderness parameter is defined based on the elastic local buckling stress of the sidewall, idealized as an infinitely long plate under patch loading. A Rayleigh-Ritz approximation is thereby used to obtain a closed-form solution. The proposed design equation is verified against experimental results over a wide range of wall slenderness values obtained from the literature and complemented by a brief experimental program carried out by the authors. It is demonstrated that the new design equation yields excellent results against the experimental data. Finally, a reliability analysis is performed within the framework of both the Eurocode and the AISI standards to ensure that the proposed design equation possesses the required level of safety. The newly proposed equation strongly outperforms the current Comité International pour le Développement et l’Etude de la Construction Tubulaire (CIDECT) design rule for sidewall buckling and also further extends the range of applicability to a wall slenderness ratio of up to 50.
Get full access to this article
View all available purchase options and get full access to this article.
References
ABAQUS [Computer software]. Dassault Systèmes, Waltham, MA.
Becque, J. (2010). “Inelastic plate buckling.” J. Eng. Mech., 1123–1130.
Becque, J., and Wilkinson, T. (2012). “Experimental investigation of the static capacity of grade C450 RHS T and X truss joints.” 14th Tubular Structures, CRC Press, London.
Becque, J., and Wilkinson, T. (2015). “A new design equation for side wall buckling of RHS truss X-joints.” 15th Tubular Structures, 1st Ed., CRC Press, Boca Raton, FL, 419–426.
Becque, J., Wilkinson, T., and Syam, A. (2011). Experimental investigation of X and T truss connections in C450 cold-formed rectangular hollow sections, Univ. of Sydney, Sydney, NSW, Australia.
Bleich, F. (1952). Buckling strength of metal structures, McGraw-Hill, New York.
Brodka, J., and Szlendak, J. (1980). “Strength of cross joints in rectangular hollow sections.” 26th Scientific Conf. of the Civil and Hydraulic Engineering Section of the Polish Academy of Science and of the Science Division of PZITB, Warsaw, Poland.
CEN (European Committee for Standardization). (2002). “Basis of structural design.” Eurocode 0, Brussels, Belgium.
CEN (European Committee for Standardization). (2005). “Design of steel structures—Part 1.1.” Eurocode 3, Brussels, Belgium.
CEN (European Committee for Standardization). (2006). “Hot finished structural hollow sections of non-alloy and fine grain steels. Technical delivery requirements.” BS EN 10210-1, Brussels, Belgium.
Davies, G., and Packer, J. (1987). “Analysis of web crippling in a rectangular hollow section.” Proc. Inst. Civ. Eng., 83(4), 785–798.
Fang, M. (2004). “Theoretical and experimental research on uniplanar X- and multiplanar XX- joints made of square hollow sections.” Ph.D. thesis, Xi’an Univ. of Architecture and Technology, Xi’an, P.R. China.
Guo, S. (2014). “Side wall buckling of RHS truss joints.” M.Sc. thesis, Univ. of Sheffield, Sheffield, U.K.
Hemp, W. S. (1945). The theory of flat panels buckled in compression, Aeronautical Research Council, Reports and Memoranda, London.
Hsiao, L. E., Yu, W. W., and Galambos, T. V. (1988). “AISI LRFD method for cold-formed steel structural members.” 9th Int. Specialty Conf. on Cold-Formed Steel Structures, Missouri Univ. of Science and Technology, Scholars’ Mine, Rolla, MO.
Lu, L. H., de Winkel, G. D., Yu, Y., and Wardenier, J. (1994). “Deformation limit for the ultimate strength of hollow section joints.” 6th Tubular Structures, Balkema, Rotterdam, Netherlands, 341–347.
Marguerre, K. (1937). “The apparent width of the plate in compression.” Luftfahrtforschung, 14(3), 121–128.
Packer, J. A. (1984). “Web crippling of rectangular hollow sections.” J. Struct. Eng., 2357–2373.
Packer, J. A., Wardenier, J., Zhao, X. L., van Der Vegte, G. J., and Kurobane, Y. (2009). Design guide for rectangular hollow section (RHS) joints under predominantly loading, CIDECT, Geneva.
Shanley, F. (1947). “Inelastic column theory.” J. Aeronaut. Sci., 14(5), 261–268.
Shen, Z. Y., and Zhang, Z. L. (1990). “Calculation of ultimate load-carrying capacity of welded RHS joints.” J. Tongji Univ., 18(3), 273–279.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability, 2nd Ed., McGraw-Hill, New York.
Wardenier, J. (1980). “The static strength of welded lattice girder joints in structural hollow sections.”, Delft Univ. of Technology, Delft, Netherlands.
Wardenier, J. (1982). Hollow section joints, Delft University Press, Amsterdam, Netherlands.
Wardenier, J., Packer, J. A., Choo, Y. S., Van Der Vegte, G. J., and Orton, A. (2009). Axially loaded T and X joints of elliptical hollow sections, CIDECT, Tampere, Finland.
Wardenier, J., Packer, J. A., Zhao, X. L., and Vegte, G. J. V. D. (2010). Hollow sections in structural applications, CIDECT, Geneva.
Zhang, Z. L., Shen, Z. Y., and Chen, X. C. (1990). “Nonlinear FEM analysis of the ultimate strength of welded RHS joints.” J. Civ. Eng., 23(1), 12–22.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Feb 2, 2016
Accepted: Aug 4, 2016
Published online: Sep 23, 2016
Published in print: Feb 1, 2017
Discussion open until: Feb 23, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.