Self-Centering Beam-to-Column Connections with Combined Superelastic SMA Bolts and Steel Angles
Publication: Journal of Structural Engineering
Volume 143, Issue 2
Abstract
This paper reveals the great potential of using combined superelastic shape memory alloy (SMA) bolts and steel angles for self-centering connections with variable performance targets. Eight full-scale specimens were tested, and the main parameters included SMA bolt prestrain, bolt length, angle thickness, and layout of bolts and angles. The specimens showed desired yielding sequences and deformation modes. The inelastic deformation was accommodated by the SMA bolts and angles with no damage to the column and beam. The specimens also exhibited very good self-centering abilities at 2% drift, beyond which the self-centering abilities were dependent on the considered parameters. A ductility capacity of at least 4% was provided by all the specimens. The maximum equivalent viscous damping ranged between 11 and 15%, indicating moderate energy dissipation. Following the test program, a design framework for such connections was proposed, and a calculation example was provided to further illustrate the proposed design procedures. The design framework was also validated through comparing the design predictions against the test results in terms of residual connection rotation.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support for this study was provided by the Collaborative Research Project under International Joint Research Laboratory of Earthquake Engineering at Tongji University and Shuguang Program supported by Shanghai Education Development Foundation and Shanghai Municipal Education Commission. Support from the Natural Science Foundation of China (NSFC) with Grant No. 51408437 is also gratefully acknowledged.
References
AISC. (2010a). “Seismic provisions for structural steel buildings.” ANSI/AISC 341-10, Chicago.
AISC. (2010b). “Specification for structural steel buildings.” ANSI/AISC 360-10, Chicago.
ATC (Applied Technology Council). (2009). “Guidelines for seismic performance assessment of buildings.”, Redwood City, CA.
CEN (European Committee for Standardization). (2004). “Design of structures for earthquake resistance—Part 1: General rules, seismic actions and rules for buildings.” Eurocode 8, Brussels, Belgium.
CEN (European Committee for Standardization). (2005). “Design of steel structures—Part 1-8: Design of joints.” Eurocode 3, Brussels, Belgium.
Chou, C. C., and Chen, J. H. (2011a). “Development of floor slab for steel post-tensioned self-centering moment frames.” J. Constr. Steel Res., 67(10), 1621–1635.
Chou, C. C., and Chen, J. H. (2011b). “Seismic design and shake table tests of a steel post-tensioned self-centering moment frame with a slab accommodating frame expansion.” Earthquake Eng. Struct. Dyn., 40(11), 1241–1261.
DesRoches, R., McCormick, J., and Delemont, M. A. (2004). “Cyclic properties of superelastic shape memory alloy wires and bars.” J. Struct. Eng., 38–46.
Eatherton, M. R., and Hajjar, J. F. (2011). “Residual drifts of self-centering systems including effects of ambient building resistance.” Earthquake Spectra, 27(3), 719–744.
Fang, C., Yam, M. C. H., Lam, A. C. C., and Xie, L. K. (2014). “Cyclic performance of extended end-plate connections equipped with shape memory alloy bolts.” J. Constr. Steel Res., 94, 122–136.
Fang, C., Yam, M. C. H., Lam, A. C. C., and Zhang, Y. Y. (2015). “Feasibility study of shape memory alloy ring spring systems for self-centring seismic resisting devices.” Smart Mater. Struct., 24(7), 075024.
FEMA. (2000). “Recommended seismic design criteria for new moment-resisting steel frame structures.”, Washington, DC.
Garlock, M., Ricles, J., and Sause, R. (2003). “Cyclic load tests and analysis of bolted top-and-seat angle connections.” J. Struct. Eng., 1615–1625.
Kim, H. J., and Christopoulos, C. (2008). “Friction damped posttensioned self-centering steel moment-resisting frames.” J. Struct. Eng., 1768–1779.
Kurama, Y., Sause, R., Pessiki, S., and Lu, L. W. (1999). “Lateral load behavior and seismic design of unbonded post-tensioned precast concrete walls.” ACI Struct. J., 96(4), 622–632.
Lagoudas, D. C. (2008). Shape memory alloys: Modeling and engineering applications, Springer, TX.
Ma, H., Wilkinson, T., and Cho, C. (2007). “Feasibility study on a self-centering beam-to-column connection by using the superelastic behavior of SMAs.” Smart Mater. Struct., 16(5), 1555–1563.
McCormick, J., and DesRoches, R. (2006). “The effect of training, pre-straining, and loading history on the properties of NiTi shape memory alloys for protective systems in civil structures.” Proc., Structures Congress 2006: Structural Engineering and Public Safety, ASCE, Reston, VA, 1–10.
Ocel, J., et al. (2004). “Steel beam-column connections using shape memory alloys.” J. Struct. Eng., 732–740.
Qiu, C. X., and Zhu, S. (2016). “High-mode effects on seismic performance of multi-story self-centering braced steel frames.” J. Constr. Steel Res., 119, 133–143.
Ricles, J., Sause, R., Peng, S., and Lu, L. (2002). “Experimental evaluation of earthquake resistant posttensioned steel connections.” J. Struct. Eng., 850–859.
Ricles, J. M., Sause, R., Garlock, M. M., and Chen, Z. (2001). “Posttensioned seismic-resistant connections for steel frames.” J. Struct. Eng., 113–121.
SAC Joint Venture. (1997). “Protocol for fabrication, inspection, testing, and documentation of beam-column connection tests and other experimental specimens.”, Sacramento, CA.
Shen, J., and Astaneh-Asl, A. (2000). “Hysteresis model of bolted angle connections.” J. Constr. Steel Res., 54(3), 317–343.
Speicher, M. S., DesRoches, R., and Leon, R. T. (2011). “Experimental results of a NiTi shape memory alloy (SMA)-based recentering beam-column connection.” Eng. Struct., 33(9), 2448–2457.
Tzimas, A. S., Dimopoulos, A. I., and Karavasilis, T. L. (2015). “EC8-based seismic design and assessment of self-centering steel frames with viscous dampers.” J. Constr. Steel Res., 105, 60–73.
Vasdravellis, G., Karavasilis, T. L., and Uy, B. (2013a). “Finite element models and cyclic behavior of self-centering steel post-tensioned connections with web hourglass pins.” Eng. Struct., 52(9), 1–16.
Vasdravellis, G., Karavasilis, T. L., and Uy, B. (2013b). “Large-scale experimental validation of steel posttensioned connections with web hourglass pins.” J. Struct. Eng., 1033–1042.
Vasdravellis, G., Karavasilis, T. L., and Uy, B. (2014). “Design rules, experimental evaluation, and fracture models for high-strength and stainless steel hourglass shape energy dissipation devices.” J. Struct. Eng., 04014087.
Wang, W., Chan, T. M., and Shao, H. L. (2015a). “Seismic performance of beam-column joints with SMA tendons strengthened by steel angles.” J. Constr. Steel Res., 109, 61–71.
Wang, W., Chan, T. M., Shao, H. L., and Chen, Y. Y. (2015b). “Cyclic behavior of connections equipped with NiTi shape memory alloy and steel tendons between H-shaped beam to CHS column.” Eng. Struct., 88, 37–50.
Wang, W., Fang, C., and Liu, J. (2016). “Large size superelastic SMA bars: Heat treatment strategy, mechanical property and seismic application.” Smart Mater. Struct., 25(7), 075001.
Wolski, M., Ricles, J. M., and Sause, R. (2009). “Experimental study of a self-centering beam-column connection with bottom flange friction device.” J. Struct. Eng., 479–488.
Yam, M. C. H., Fang, C., Lam, A. C. C., and Zhang, Y. Y. (2015). “Numerical study and practical design of beam-to-column connections with shape memory alloys.” J. Constr. Steel Res., 104, 177–192.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Apr 26, 2016
Accepted: Aug 4, 2016
Published online: Sep 19, 2016
Published in print: Feb 1, 2017
Discussion open until: Feb 19, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.