Experimental Study of Self-Centering Shear Walls with Horizontal Bottom Slits
Publication: Journal of Structural Engineering
Volume 143, Issue 3
Abstract
This paper introduces a new design form for prestressed shear walls with horizontal bottom slits utilizing cast-in-place technology. Horizontal slits are placed symmetrically at the wall-foundation interface of prestressed shear walls while the concrete in the middle of the wall width remains connected with the foundation. Furthermore, unbonded prestressed tendons inside the wall are adopted to provide self-centering ability. Tests on prestressed self-centering shear walls with horizontal bottom slits under cyclic loading were conducted to investigate their seismic performance. Test results were analyzed from the tests, and a comparison was made among traditional shear wall and self-centering shear walls with horizontal bottom slits of different configurations. The experimental results indicate that the tested cast-in-place shear walls exhibit excellent self-centering ability with the lateral load capacity similar to traditional shear walls. The quantity and distribution range of the cracking in the walls were significantly reduced, to the advantage of damage reduction. The flexural/shear deformations and the strains of the walls were limited to a very low level as the deformations were concentrated at the bottom of the shear walls. According to the results of the tests, an analysis method was presented to calculate the flexural strength of the proposed shear walls.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research is funded by the National Natural Science Foundation of China (91315301-4) and State Key Laboratory of Disaster Reduction in Civil Engineering (SLDRCE14-A-07). Any opinions, findings, conclusions, or recommendations expressed in this paper are those of the authors and do not necessarily represent the views of the individuals or organizations acknowledged.
References
ACI (American Concrete Institute). (2007). “Acceptance criteria for special unbonded post-tensioned precast structural walls based on validation testing.” ACI ITG5.1-07, Farmington Hills, MI.
ACI (American Concrete Institute). (2009). “Requirements for design of a special unbonded post-tensioned precast structural walls satisfying ACI ITG-5.1.” ACI ITG5.2-09, Farmington Hills, MI.
Erkmen, B., and Schultz, A. E. (2009). “Self-centering behavior of unbonded, post-tensioned precast concrete shear walls.” J. Earthquake Eng., 13(7), 1047–1064.
Hamid, N. H., and Mander, J. B. (2010). “Lateral seismic performance of multipanel precast hollowcore walls.” J. Struct. Eng., 795–804.
Henry, R. S. (2011) “Self-centering precast concrete walls for buildings in regions with low to high seismicity.” Univ. of Auckland, Auckland, New Zealand.
Holden, T., Restrepo, J., and Mander, J. (2003). “Seismic performance of precast reinforced and prestressed concrete walls.” J. Struct. Eng., 286–296.
Jacobsen, L. S., and Ayre, R. S. (1958). Engineering vibrations with applications to structures and machinery, McGraw-Hill, New York.
Kurama, Y., Sause, R., Pessiki, S., and Lu, L. W. (1999). “Lateral load behavior and seismic design of unbonded post-tensioned precast concrete walls.” ACI Struct. J., 96(4), 622–633.
Massone, L. M., and Wallace, J. W. (2004). “Load-deformation responses of slender reinforced concrete walls.” ACI Struct. J., 101(1), 103–113.
Nagae, T, et al. (2011). “Design and instrumentation of 2010 E-defense four-story reinforced concrete and post-tensioned concrete buildings.”, Pacific Earthquake Engineering Research Center (PEER), Univ. of California, Berkeley, CA.
NZS (New Zealand Standards). (2006). “Concrete structures standard.” NZS 3101, Wellington, New Zealand.
Panian, L., Steyer, M., and Tipping, S. (2007). “An innovative approach to earthquake safety and concrete construction in buildings.” J. Post-Tens. Inst., 5(1), 7–16.
Perez, F. J., Pessiki, S., and Sause, R. (2013). “Experimental lateral load response of unbonded post-tensioned precast concrete walls.” ACI Struct. J., 110(6), 1045–1055.
Perez, F. J., Sause, R., and Pessiki, S. (2007). “Analytical and experimental lateral load behavior of unbonded posttensioned precast concrete walls.” J. Struct. Eng., 1531–1540.
Rahman, A., and Sritharan, S. (2007). “Performance-based seismic evaluation of two five-story precast concrete hybrid frame buildings.” J. Struct. Eng., 1489–1500.
Restrepo, J., and Rahman, A. (2007). “Seismic performance of self-centering structural walls incorporating energy dissipators.” J. Struct. Eng., 1560–1570.
Smith, B. (2012). “Design, analysis and experimental evaluation of hybrid precast concrete shear walls for seismic regions.” Univ. of Notre Dame, Notre Dame, IN.
Smith, B., Kurama, Y., and McGinnis, M. (2011). “Design and measured behavior of a hybrid precast concrete wall specimen for seismic regions.” J. Struct. Eng., 1052–1062.
Sritharan, S., Aaleti, S., Henry, R. S., Liu, K. Y., and Tsai, K. C. (2015). “Precast concrete wall with end columns (PreWEC) for earthquake resistant design.” Earthquake Eng. Struct. Dyn., 44(12), 2075–2092.
Stevenson, M., Panian, L., Korolyk, M., and Mar, D. (2008). “Post-tensioned concrete walls and frames for seismic-resistance: A case study of the David Brower Center.” Proc., SEAOC Annual Convention, SEAOC, Sacramento, CA.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Dec 25, 2015
Accepted: Aug 3, 2016
Published online: Sep 26, 2016
Discussion open until: Feb 26, 2017
Published in print: Mar 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.