Investigating the Behavior of Light-Frame Wood Stud Walls Subjected to Severe Blast Loading
Publication: Journal of Structural Engineering
Volume 142, Issue 12
Abstract
An understanding of the behavior of wood stud walls in a region corresponding to hazardous-blowout damage levels is currently lacking. The focus of the current study is on investigating the flexural response of full-scale wood stud walls subjected to pressure-impulse combinations that would yield severe damage levels. Static material properties were determined and used as input in an analytical model that considers the nonlinear behavior of stud-to-sheathing joints, as well as high strain-rate effects. Experimental results showed that premature sheathing failure could occur prior to full flexural stud response, and that sheathing panel debris could be generated. The use of thicker sheathing and screws shifted the failures to the studs, while decreasing the amount of debris. Welded wire mesh was successfully used as a reinforcement of the sheathing or as a catcher system while maintaining the residual axial capacity of the studs. A single-degree-of-freedom material-predictive model was successfully validated using the experimental test results.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (2006). “Evaluating properties of wood-base fiber and particle panel material.” ASTM D1037-06a, West Conshohocken, PA.
ASTM. (2009). “Static tests of lumber in structural sizes.” ASTM D198-09, West Conshohocken, PA.
ASTM. (2012). “Standard test methods for mechanical fasteners in wood.” ASTM D1761-12, West Conshohocken, PA.
Biggs, M. (1964). Introduction to structural dynamics, New York.
Bogosian, D., and Avanessian, H. D. (2004). “Blunt trauma from blast-induced building debris.” 31st Explosives Safety Seminar, U.S. Dept. of Defense, VA, 1–20.
Bulleit, W., Pang, W. C., and Rosowsky, D. (2005). “Modeling wood walls subjected to combined transverse and axial loads.” J. Struct. Eng., 781–793.
CSA (Canadian Standards Association). (2012). “Design and assessment of buildings subjected to blast loads.” CSA S850-12, Mississauga, ON.
Department of the Air Force. (2006). “Vehicle bomb mitigation guide.” Airforce handbook 10-2401, San Antonio.
Gromala, D. S. (1983). “Light-frame wall systems: Performance and predictability.” United States Dept. of Agriculture, Madison, WI.
Guy, R. J., Glover, M. A., and Cripps, N. P. (1998). “The pathophysiology of primary blast injury and its implications for treatment. Part I: The thorax.” J. R. Nav. Med. Serv., 84(2), 79–86.
Jacques, E., Lloyd, A., Braimah, A., Saatcioglu, M., Doudak, G., and Abdelalim, O. (2013). “Influence of high strain-rates on the dynamic flexural material properties of spruce-pine-fir wood studs.” Can. J. Civ. Eng., 41(1), 56–64.
Jansson, B. (1992). “Impact loading of timber beams.” MASc thesis, Univ. of British Columbia, Vancouver, BC, Canada.
Jensen, J. H., and Bonding, P. (1993). “Experimental pressure induced rupture of the tympanic membrane in man.” Acta Otolaryngol, 113(1), 62–67.
Katz, E., Ofek, B., Adler, J., Abramowitz, H. B., and Krausz, M. M. (1989). “Primary blast injury after a bomb explosion in a civilian bus.” Ann. Surg., 209(4), 484–488.
Lacroix, D. N. (2013). “Behaviour of light-frame wood stud walls subjected to blast loading.” MASc thesis, Univ. of Ottawa, Ottawa, ON.
Lacroix, D. N., and Doudak, G. (2013). “Modelling the behaviour of light-frame wood stud walls subjected to blast loading.” 3rd Specialty Conf. on Material Engineering and Applied Mechanics, Canadian Society for Civil Engineering, Montreal, QC, 1–10.
Lacroix, D. N., and Doudak, G. (2014). “Investigation of dynamic increase factors in light-frame wood stud walls subjected to out-of-plane blast loading.” J. Struct. Eng., 04014159.
Lacroix, D. N., Doudak, G., and El-Domiaty, K. (2013). “Retrofit options for light-frame wood stud walls subjected to blast loading.” J. Struct. Eng., 04013104.
Liu, W., and Bulleit, W. (1995). “Overload behavior of sheathed lumber systems.” J. Struct. Eng., 1110–1118.
Lloyd, A. (2010). “Performance of reinforced concrete columns under shock tube induced shock wave loading.” MASc thesis, Univ. of Ottawa, Ottawa, ON.
Lloyd, A., and Jacques, E. (2011). “Innovative and cost effective blast strengthening of wood framed structures.”, National Homeland Defense Foundation, Colorado Springs, CO.
Marchand, K. A. (2002). “BAIT, BASS & RODS testing results.” USAF Protection Battlelab, San Antonio.
McCutcheon, W. J. (1977). “Method for predicting the stiffness of wood-joist floor systems with partial composite action.” U.S. Dept. of Agriculture, Madison, WI.
McCutcheon, W. J. (1986). “Stiffness of framing members with partial composite action.” J. Struct. Eng., 1623–1637.
Mindess, S., and Madsen, B. (1986). “The fracture of wood under impact loading.” J. Mater. Struct., 19(1), 49–53.
Nadeau, J., and Bennett, R. (1982). “An explanation for the rate-of-loading and duration-of-load effects in wood in terms of fracture mechanics.” J. Mater. Sci., 17(10), 2831–2840.
Parlin, N. (2010). “Behavior of FRP-coated wood panels under dynamic loading.” M.S. thesis, Univ. of Maine, Orono, ME.
Polensek, A., and Schimel, B. (1986). “Rotational restraint of wood-stud wall supports.” J. Struct. Eng., 1247–1262.
Rosowsky, D. V., Yu, G., and Bulleit, W. M. (2005). “Reliability of light-frame wall systems subject to combined axial and transverse loads.” J. Struct. Eng., 1444–1455.
Spencer, R. (1978). “Rate of loading effect in bending for Douglas-Fir Lumber.” Proc., 1st Int. Conf. on Wood Fracture, Western Forest Products Laboratory, Vancouver, BC, Canada, 259–265.
Sukontasukkul, P., Lam, F., and Mindess, S. (2000). “Fracture of parallel strand lumber (PSL) under impact loading.” Mater. Struct., 33(7), 445–449.
Syron, W. (2010). “Strain rate-dependent behavior of laminated strand lumber.” M.S. thesis, Univ. of Maine, Orono, ME.
USACE (U.S. Army Corps of Engineers). (2008). “Methodology manual for the single-degree-of-freedom blast effects design spreadsheets.” Washington, DC.
U.S. Department of Defense. (2008). “Structures to resist the effects of accidental explosions.” Washington, DC.
Wheat, D. L., Vanderbilt, D., and Goodman, J. R. (1983). “Wood floors with nonlinear nail stiffness.” J. Struct. Eng., 1290–1302.
Yu, G. (2003). “Load sharing and system factors for light-frame wall systems.” Ph.D. thesis, Oregon State Univ., Corvallis, OR.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Oct 15, 2015
Accepted: Jun 8, 2016
Published online: Jul 19, 2016
Published in print: Dec 1, 2016
Discussion open until: Dec 19, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.