Strength of Concrete Struts in Three-Dimensional Strut-Tie Models
Publication: Journal of Structural Engineering
Volume 142, Issue 11
Abstract
The design of structural concrete using strut-tie models requires establishing the effective strength of concrete struts, ensuring sufficient anchorage of reinforcing bars in nodal zones, and the geometric compatibility of the strut-tie model within the member geometry. In this paper, a consistent and general method applicable to three-dimensional (3D) strut-tie models is presented. The proposed method includes the effects of 3D stresses associated with tensile strains in reinforcing bars crossing a strut, strut length, deviation angle between strut orientation and compressive principal stress flow, compressive strength of concrete, and degree of confinement provided by reinforcement. The proposed method is implemented and then verified using data from 115 reinforced concrete pile caps tested to failure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2015R1D1A1A01061333).
References
AASHTO. (2010). AASHTO LRFD bridge design specifications, 5th Ed., Washington, DC.
ACI (American Concrete Institute). (2002). “SP-208: Examples for the design of structural concrete with strut-and-tie models.” ACI Committee 445, Farmington Hills, MI.
ACI (American Concrete Institute). (2014). “Building code requirements for structural concrete (ACI 318-14) and commentary.” Farmington Hills, MI.
Adebar, P., Kuchma, D., and Collins, M. P. (1990). “Strut-and-tie models for the design of pile caps: An experimental study.” ACI Struct. J., 87(1), 81–92.
Adebar, P., and Zhou, L. (1996). “Design of deep pile caps by strut-and-tie models.” ACI Struct. J., 93(4), 437–448.
Alshegeir, A. (1992). “Analysis and design of disturbed regions with strut-tie models.” Ph.D. dissertation, School of Civil Engineering, Purdue Univ., West Lafayette, IN.
Bergmeister, K., Breen, J. E., Jirsa, J. O., and Kreger, M. E. (1993). “Detailing in structural concrete.”, Center for Transportation Research, Univ. of Texas at Austin, Austin, TX.
Canadian Standards Association. (2004). “Design of concrete structures for buildings.”, Rexdale, ON, Canada.
CEN (European Committee for Standardization). (2004). Eurocode 2: Design of concrete structures, Brussels, Belgium.
Clarke, J. L. (1973). “Behavior and design of pile caps with four piles.”, Cement and Concrete Association, London.
fib (International Federation for Structural Concrete). (2010). “CEP-FIP model code 2010.” Comité Euro-International du Béton, Lausanne, Switzerland.
Kim, B. H., Chae, H. S., and Yun, Y. M. (2013). “Refined 3-dimensional strut-tie models for analysis and design of reinforced concrete pile caps.” J. Korean Soc. Civ. Eng., 33(1), 115–130.
MacGregor, J. G. (1997). Reinforced concrete—Mechanics and design, 4th Ed., Prentice Hall, Englewood Cliffs, NJ.
Marti, P. (1985). “Basic tools of reinforced concrete beam design.” J. Am. Concr. Inst., 82(1), 46–56.
Nielsen, M. P., Braestrup, M. W., Jensen, B. C., and Bach, F. (1978). Concrete plasticity, beam shear—Shear in joints—Punching shear, Danish Society for Structural Science and Engineering, Lyngby, Denmark.
PCA (Portland Cement Association). (2004). AASHTO LRFD strut-tie model design examples, Skokie, IL.
Potzl, M. (1993). “Pile cap subjected to vertical forces and moments.” Germany.
Ramirez, J. A., and Breen, J. E. (1983). “Proposed design procedure for shear and torsion in reinforced and prestressed concrete.”, Center for Transportation Research, Univ. of Texas at Austin, Austin, TX.
Sabnis, G. M., and Gogate, A. B. (1984). “Investigation of thick slab (pile cap) behavior.” ACI J., 81(1), 35–39.
Schlaich, J., Schaefer, K., and Jennewein, M. (1987). “Towards a consistent design of structural concrete.” J. Prestressed Concr. Inst., 32(3), 74–151.
Suzuki, K., and Otsuki, K. (2002). “Experimental study on corner shear failure of pile caps.” Trans. Jpn. Concr. Inst., 23, 303–310.
Suzuki, K., Otsuki, K., and Tsubata, T. (1998). “Influence of bar arrangement on ultimate strength of four-pile caps.” Trans. Jpn. Concr. Inst., 20, 195–202.
Suzuki, K., Otsuki, K., and Tsubata, T. (1999). “Experimental study on four-pile caps with taper.” Trans. Jpn. Concr. Inst., 21, 361–368.
Suzuki, K., Otsuki, K., and Tsuchiya, T. (2000). “Influence of edge distance on failure mechanism of pile caps.” Trans. Jpn. Concr. Inst., 22, 327–334.
Thurlimann, B. (1976). Shear strength of reinforced and prestressed concrete—CEB approach, American Concrete Institute, Detroit.
Vecchio, F. J., and Collins, M. P. (1982). The response of reinforced concrete to in-plane shear and normal stresses, Dept. of Civil Engineering, Univ. of Toronto, Toronto.
Willam, K. J., and Warnke, E. P. (1975). “Constitutive model for the triaxial behavior of concrete.” IABSE Proc., 19, 1–30.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Jun 13, 2015
Accepted: Apr 5, 2016
Published online: Jun 29, 2016
Published in print: Nov 1, 2016
Discussion open until: Nov 29, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.