Steel Connections with Fiber-Reinforced Resin Thermal Barrier Filler Plates under Service Loading
Publication: Journal of Structural Engineering
Volume 142, Issue 11
Abstract
Fiber-reinforced resin (FRR) plates are being incorporated into structural joints to correct thermal bridging issues to create more energy-efficient buildings. The purpose of this study was to evaluate the behaviors of simple shear and moment connections that include FRR thermal barrier plates under service-loading conditions. Tests included two thicknesses and two grades of barrier plate. The shear connection tests showed that the coefficient of friction between steel and an as-received FRR plate was significantly lower than that of steel on steel. However, roughening the FRR plates by blasting with aluminum oxide increased the coefficient to nearly the same as or greater than steel on steel. In moment connections the presence of thermal barrier plates increased the joint rotation at the connection. A 25-mm (1-in.) thermal barrier plate increased the joint rotation by 10% compared to a joint without the barrier plate. The increase was 20% for a 50-mm (2-in.) plate. The thermal barrier plates did not affect the dynamic response of the test fixture at structurally important frequencies.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The work presented was partially funded by Armadillo Noise and Vibration Control. The findings are strictly those of the authors. Charles Linderman, Aaron Nolan, and Karl Dyer of Rowan University were instrumental in assisting with specimen and loading frame fabrication. Dr. Eric Constans assisted with vibration measurements.
References
ABET Engineering Accreditation Commission. (2014). “2014-2015 criteria for accrediting engineering programs.” Baltimore.
AISC. (2011). Steel construction manual, 14th Ed., Chicago.
ANSI (American National Standards Institute). (2012). “Standard specification for the size of abrasive grain–grinding wheels, polishing, and general industrial use.” ANSI 874.12-2012, Washington, DC.
Appelfeld, D., Hansen, C. S., and Svendsen, S. (2010). “Development of a slim window frame made of glass fibre reinforced polyester.” Energy Build., 42(10), 1918–1925.
Armenakas, A. (2005). “The Timoshenko theory of beams.” Advanced mechanics of materials and applied elasticity, Taylor and Francis, Boca Raton, FL, 421.
ASCE. (2006). Code of ethics, Reston, VA.
ASTM. (2006). “Standard practice for measuring the change in length of fasteners using the ultrasonic pulse-echotechnique.” ASTM E1685–00, West Conshohocken, PA.
ASTM. (2010). “Standard specification for structural bolts, steel, heat treated, minimum tensile strength.” ASTM A325-10, West Conshohocken, PA.
ASTM. (2011). “Standard specification for hardened steel washers.” ASTM F436-11, West Conshohocken, PA.
ASTM. (2014). “Standard specification for carbon and alloy steel nuts.” ASTM A563-07, West Conshohocken, PA.
Cappelletti, F., Gasparella, A., Romagnoni, P., and Baggio, P. (2011). “Analysis of the influence of installation thermal bridges on windows performance: The case of clay block walls.” Energy Build., 43(6), 1435–1442.
CEN (European Committee for Standardization). (2005). “Eurocode 3: Design of steel structures—Design of joints.” EN 1993-1-8, Brussels, Belgium.
Evola, G., Margani, G., and Marletta, L. (2011). “Energy and cost evaluation of thermal bridge correction in Mediterranean climate.” Energy Build., 43(9), 2385–2393.
Goulouti, K., De Castro, J., Vassilopoulos, A. P., and Keller, T. (2014). “Thermal performance evaluation of fiber-reinforced polymer thermal breaks for balcony connections.” Energy Build., 70, 365–371.
Keller, T., Riebel, F., and Zhou, A. (2006). “Multifunctional hybrid GFRP/steel joint for concrete slab structures.” J. Compos. Constr., 550–560.
Miller-Johnson, R. (2010). “Structuring sustainable thermal breaks: Opportunities and liabilities.” Proc., 2010 Structures Congress, ASCE, Reston, VA, 1384–1392.
Nasdala, L., Hohn, B., and Ruhl, R. (2007). “Design of end-plate connections with elastomeric intermediate layer.” J. Constr. Steel Res., 63(4), 494–504.
Oostdyk, M., Polhemus, M., Gabrielsen, A., Cleary, D. B., and Riddell, W. T. (2015). “Time dependent behavior of a FRR thermal break pad under compressive loads.” Structures, 2, 44–49.
Research Council on Structural Connections. (2009). “Specification for structural joints using high-strength bolts.” Chicago.
Schneider, M. and Fischer, H.-M. (2008). “Vibration reduction of thermal break balcony connections.” Acoustics 08, Paris.
Sulcova, Z., Sokol, Z., and Wald, F. (2007). “Structural connections with thermal separation.” Proc., CESB 07 Prague International Conf., Vol. 2, Czech Technical Univ., Prague, Czech Republic, 672–677.
Sulcova, Z., Sokol, Z., and Wald, F. (2010). “Integration of the new component into the design method for thermal insulating connections.” Portugal SB10—Sustainable Building Affordable to All: Low Cost Sustainable Solutions, Universidade do Minho, Braga, Portugal.
Theodosiou, T. G., and Papadopoulos, A. M. (2008). “The impact of thermal bridges on the energy demand of buildings with double brick wall constructions.” Energy Build., 40(11), 2083–2089.
Wakili, K. G., Simmler, H., and Frank, T. (2007). “Experimental and numerical thermal analysis of a balcony board with integrated glass fibre reinforced polymer GFRP elements.” Energy Build., 39(1), 76–81.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Nov 13, 2015
Accepted: Mar 21, 2016
Published online: May 25, 2016
Discussion open until: Oct 25, 2016
Published in print: Nov 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.