Computationally Efficient Vector-Valued Seismic Risk Analysis of Engineering Structures
Publication: Journal of Structural Engineering
Volume 142, Issue 9
Abstract
Probabilistic seismic risk analysis (SRA) is often used for accurately quantifying seismic risk of critical engineering structures. It combines the probabilistic model of the behavior of structural response given a ground motion parameter (GMP) (e.g., seismic fragility model) and the probabilistic seismic hazard analysis (PSHA) for the GMP in a mathematically rigorous manner. In current engineering practice, SRA is performed based on a single GMP. For structures whose responses can be better predicted using multiple GMPs, a vector-valued SRA (VSRA) gives more accurate estimates of risk. However, due to the extensive computational efforts required for the multiple-dimensional cases, VSRA has not been widely applied in engineering practice. This paper presents a simplified approach to VSRA, which can substantially improve computational efficiency without losing accuracy. A new seismic hazard deaggregation procedure is proposed to determine a set of controlling earthquakes in terms of magnitude, source-site distance, and occurrence rate for the site of interest. VSRA is then performed based on the controlling earthquakes rather than all possible earthquake occurrences. Two numerical examples are presented to validate the effectiveness and accuracy of the simplified approach. Factors affecting the approximations in the simplified approach are discussed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research for this paper was supported, in part, by the Natural Sciences and Engineering Research Council of Canada (NSERC) and University Network of Excellence in Nuclear Engineering (UNENE).
References
Abrahamson, N., and Silva, W. (1997). “Empirical response spectral attenuation relations for shallow crustal earthquakes.” Seismol. Res. Lett., 68(1), 94–127.
Adams, J., and Halchuk, S. (2003). “Fourth generation seismic hazard maps of Canada: Values for over 650 Canadian localities intended for the 2005 National Building Code of Canada.” Geological Survey of Canada, Ottawa.
ASCE. (2005). “Seismic design criteria for structures, systems, and components in nuclear facilities.” ASCE/SEI 43-05, Reston, VA.
Atkinson, G., and Boore, D. (2006). “Earthquake ground-motion prediction equations for eastern North America.” Bull. Seismol. Soc. Am., 96(6), 2181–2205.
Baker, J., and Cornell, C. (2005). “Vector-valued ground motion intensity measures for probabilistic seismic demand analysis.”, John A. Blume Earthquake Engineering Center, Stanford Univ., Stanford, CA.
Baker, J., and Cornell, C. (2006). “Correlation of response spectral values for multicomponent ground motions.” Bull. Seismol. Soc. Am., 96(1), 215–227.
Baker, J., and Jayaram, N. (2008). “Correlation of spectral acceleration values from NGA ground motion models.” Earthquake Spectra, 24(1), 299–317.
Bazzurro, P., and Cornell, C. (1999). “Disaggregation of seismic hazard.” Bull. Seismol. Soc. Am., 89(2), 501–520.
Bazzurro, P., and Cornell, C. (2002). “Vector-valued probabilistic seismic hazard analysis.” Proc., 7th U.S. National Conf. on Earthquake Engineering, Earthquake Engineering Research Institute, Oakland, CA.
Bertero, R., and Bertero, V. (2002). “Performance-based seismic engineering: The need for a reliable conceptual comprehensive approach.” Earthquake Eng. Struct. Dyn., 31(3), 627–652.
Boore, D., and Atkinson, G. (2008). “Ground-motion prediction equations for the average horizontal component of PGA, PGV, and 5%-damped PSA at spectral periods between 0.01 and 10.0s.” Earthquake Spectra, 24(1), 99–138.
Cornell, C. (1968). “Engineering seismic risk analysis.” Bull. Seismol. Soc. Am., 58(5), 1583–1606.
Cosentino, P., Ficarra, V., and Luzio, D. (1977). “Truncated exponential frequency-magnitude relationship in earthquake statistics.” Bull. Seismol. Soc. Am., 67(6), 1615–1623.
EPRI (Electric Power Research Institute). (2013). “Seismic evaluation guidance: Screening, prioritization and implementation details (SPID) for the resolution of Fukushima near-term task force recommendation 2.1.”, Palo Alto, CA.
Gupta, A., and Krawinkler, H. (1999). “Seismic demands for performance evaluation of steel moment resisting frame structures.”, John A. Blume Earthquake Engineering Center, Stanford Univ., Stanford, CA.
Gutenberg, B., and Richter, C. (1944). “Frequency of earthquakes in California.” Bull. Seismol. Soc. Am., 34(4), 185–188.
Hardebeck, J. L. (2013). “Geometry and earthquake potential of the Shoreline fault, central California.” Bull. Seismol. Soc. Am., 103(1), 447–462.
Jayaram, N., and Baker, J. (2008). “Statistical tests of the joint distribution of spectral acceleration values.” Bull. Seismol. Soc. Am., 98(5), 2231–2243.
Jeong, S., and Elnashai, A. (2007). “Probabilistic fragility analysis parameterized by fundamental response quantities.” Eng. Struct., 29(6), 1238–1251.
McGuire, R. (1995). “Probabilistic seismic hazard analysis and design earthquakes: Closing the loop.” Bull. Seismol. Soc. Am., 85(5), 1275–1284.
McGuire, R. (2004). Seismic hazard and risk analysis, Earthquake Engineering Research Institute, Oakland, CA.
Ni, S.-H., Zhang, D.-Y., Xie, W.-C., and Pandey, M. (2012). “Vector-valued uniform hazard spectra.” Earthquake Spectra, 28(4), 1549–1568.
Shinozuka, M., Feng, M., Lee, J., and Naganuma, T. (2000). “Statistical analysis of fragility curves.” J. Eng. Mech., 1224–1231.
Shome, N. (1999). “Probabilistic seismic demand analysis of nonlinear structures.” Ph.D. thesis, Stanford Univ., Stanford, CA.
Tothong, P., and Luco, N. (2007). “Probabilistic seismic demand analysis using advanced ground motion intensity measures.” Earthquake Eng. Struct. Dyn., 36(13), 1837–1860.
USGS (U.S. Geological Survey). (2008). “Documentation for the 2008 update of the United States national seismic hazard maps.”, Washington, DC.
USGS (U.S. Geological Survey) and CGS (California Geological Survey). (2013). “Uniform California earthquake rupture forecast, version 3 (UCERF3): The time-independent model.”, Washington, DC.
USGS (U.S. Geological Survey) and CGS (California Geological Survey). (2014). “Quaternary fault and fold database for the United States.” 〈http//earthquake.usgs.gov/hazards/qfaults/〉 (Jan. 9, 2014).
Wen, Y. (2001). “Reliability and performance-based design.” Struct. Saf., 23(4), 407–428.
WGCEP (Working Group on California Earthquake Probabilities). (2003). “Earthquake probabilities in the San Francisco Bay region: 2002–2031.”, U.S. Geological Survey, Washington, DC.
Wills, C., Weldon, R., and Bryant, W. (2008). “Appendix: California fault parameters for the national seismic hazard map and working group on California earthquake probabilities.”, U.S. Geological Survey, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Mar 13, 2015
Accepted: Jan 4, 2016
Published online: Apr 1, 2016
Published in print: Sep 1, 2016
Discussion open until: Sep 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.