Behavior and Strength of Headed Stud–SFRCC Shear Connection. I: Experimental Study
Publication: Journal of Structural Engineering
Volume 142, Issue 2
Abstract
The performance of a single-headed stud and group of studs embedded in steel-fiber-reinforced cementitious composites (SFRCC) were investigated by conducting push-out tests. A total of 16 specimens were tested with various parameters including diameter of studs, numbers of studs, gauge lengths, pitch lengths, and fiber volume fractions of SFRCC. The test results showed that the headed studs embedded in SFRCC ensured the failure mode of stud fracture even without using steel rebar in the slab. The studs densely arranged with the smallest pitch length permitted for installation provided more than 90% of the full shear strength of a single stud. Using nine studs densely arranged in an area allowing for only four studs in the current design code, the overall shear resistance was twice that of the conventional design. When the fiber volume fraction of SFRCC directly affects the ductility of the stud, it was found using a fiber volume fraction of 6% is most suitable.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO and LRFD. (2012). “Bridge design specifications, 2012.” Washington, DC.
An, L., and Cederwall, K. (1996). “Push-out tests on studs in high strength and normal strength concrete.” J. Constr. Steel Res., 36(1), 15–29.
Anderson, N. S., and Meinheit, D. F. (2005). “Pryout capacity of cast-in headed stud anchors.” PCI J., 50(2), 90–112.
ANSI/AISC (American National Standard Institute). (2010). “Specification for structural steel buildings.” ANSI/AISC 360, Chicago.
Architectural Institute of Japan. (2010). “Design recommendations for composite constructions.” Tokyo.
Bache, H. H. (1981a). “Compact reinforced concrete composite, basic principles.” Aalborg Portland, Aalborg, Denmark.
Bache, H. H. (1981b). “Densified cement/ultra-fine particle-based materials.” Conf. on Superplasticizers in Concrete, Aalborg Portland, Cement and Concrete Lab.
CEN (European Committee for Standardization). (1994). “Design of composite steel and concrete structures.”, Brussels.
Cui, Y., Luo, Y., and Nakashima, M. (2013). “Development of steel beam-to-column connections using sfrcc slabs.” Eng. Struct., 52, 545–557.
Kaneko, Y., Mihashi, H., Kirikoshi, K., and Abe, T. (2001). “New application filed of steel fiber reinforced cementitous composites-experiment on column-beam joint in steel structures.” J. Archit. Build. Sci., 116(1481), 119–122.
Li, V. C., and Kanda, T. (1998). “Engineered cementitious composites for structural applications.” J. Mater. Civ. Eng., 66–69.
Nielsen, C. V. (1995). “Ultra high-strength steel fibre reinforced concrete. Part I: Basic strength properties of compresit matrix.” Technical Univ. of Denmark, Copenhagen, Denmark, 323.
Oehlers, D. (1989). “Splitting induced by shear connectors in composite beams.” J. Struct. Eng., 341–362.
Oehlers, D., and Coughlan, C. (1986). “The shear stiffness of stud shear connections in composite beams.” J. Constr. Steel Res., 6(4), 273–284.
Okada, J., Yoda, T., and Lebet, J.-P. (2006). “A study of the grouped arrangements of stud connectors on shear strength behavior.” Struct. Eng. Earthquake Eng., 23(1), 75S–89S.
Okubo, N., and Kurita, A. (2005). “Application of grouped studs to continuous composite girder bridges.” Proc. Jpn Soc. Civ. Eng., 780, 545–557.
Ollgaard, J. G., Slutter, R. G., and Fisher, J. W. (1971). “Shear strength of stud connectors in lightweight and normal-weight concrete.” AISC Eng. J., 8(2), 55–64.
Qian, S., and Li, V. C. (2009). “Influence of concrete material ductility on headed anchor pullout performance.” ACI Mater. J., 106(1), 72.
Viest, I. M. (1956). “Investigation of stud shear connectors for composite concrete and steel t-beams.” ACI J., 52(4), 875–892.
Xu, C., and Sugiura, K. (2013). “Parametric push-out analysis on group studs shear connector under effect of bending-induced concrete cracks.” J. Constr. Steel Res., 89, 86–97.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Sep 11, 2014
Accepted: Jun 2, 2015
Published online: Jul 31, 2015
Discussion open until: Dec 31, 2015
Published in print: Feb 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.