Experimental Characterization of a Composite Slab Subjected to Simulated Column Removal Loading
Publication: Journal of Structural Engineering
Volume 142, Issue 1
Abstract
Steel gravity frames are inherently simple systems, which has led to questions regarding their structural integrity or robustness. The concept of structural integrity is often tied to column removal scenarios in which the structure must develop alternate load paths. The mobilization of the composite slab with ribbed metal decking as a part of this behavior, theorized to be via membrane action, shifts the loading in the slab from bending to primarily tension. This study consists of composite slab component tests that include uniaxial tests in both orthogonal directions with respect to the deck corrugations, and shear and tension tests of the side lap splices. Also included are transverse uniaxial slab tests with additional reinforcement, and tension tests of the support fastener connections between the metal deck and beams and girders. The test results show the composite slab to be weak in the transverse direction regardless of side lap engagement and strong but susceptible to debonding in the longitudinal direction. They also cast doubt on the ability of the support fasteners to develop the longitudinal strength.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The collaborative research was funded by the National Science Foundation under Grant Nos. CMMI-1000926, CMMI-0969837 (this paper), and CMMI-1000077, with additional support from the American Institute of Steel Construction. Any opinions, findings, conclusions, and recommendations are those of the authors, and do not necessarily reflect the views of the sponsors.
References
ACI (American Concrete Institute). (2011). “Building code requirements for structural concrete and commentary.”, Farmington Hills, MI.
Alashker, Y., and El-Tawil, S. (2011). “A design-oriented model for the collapse resistance of composite floors subjected to column loss.” J. Constr. Steel Res., 67(1), 84–92.
Alashker, Y., El-Tawil, S., and Sadek, F. (2010). “Progressive collapse resistance of steel-concrete composite floors.” J. Struct. Eng., 1187–1196.
ASCE. (2010). “Minimum design loads for buildings and other structures.”, Reston, VA.
Astaneh-Asl, A., et al. (2001a). “Use of catenary cables to prevent progressive collapse of buildings.”, Dept. of Civil and Environmental Engineering, Univ. of California, Berkeley, CA.
Astaneh-Asl, A., Jones, B., Zhao, Y., and Hwa, R. (2001b). “Progressive collapse resistance of steel building floors.”, Dept. of Civil and Environmental Engineering, Univ. of California, Berkeley, CA.
DoD (Department of Defense). (2009). “Design of buildings to resist progressive collapse.”, Washington, DC.
FEMA (Federal Emergency Agency). (2000). “State of the art report on connection performance.”, Washington, DC.
Foley, C., Martin, K., and Schneeman, C. (2007). “Robustness in structural steel framing systems.”, Marquette Univ., Milwaukee.
Jahromi, H., et al. (2012). “Robustness assessment of building structures under explosion.” Buildings, 2(4), 497–518.
Jamshidi, A., and Driver, R. (2014). “Full-scale tests on shear connections of composite beams under a column removal scenario.” ASCE/SEI Structures Congress, ASCE/Structural Engineering Institute (SEI), Reston, VA.
Johnson, E., Meissner, J., and Fahnestock, L. (2015). “Experimental behavior of a large-scale steel-concrete composite floor system subjected to column removal scenarios.” J. Struct. Eng., in press.
Kwasniewski, L. (2010). “Nonlinear dynamic simulations of progressive collapse for a multistory building.” Eng. Struct., 32(5), 1223–1235.
Main, J., and Sadek, F. (2012). “Robustness of steel gravity-frame systems with single-plate shear connections.”, National Institute of Standards and Technology, Gaithersburg, MD.
Nawy, E., and Ukadike, M. (1983). “Shear transfer in concrete and polymer modified concrete members subjected to shearing loads.” J. Test. Eval., 11(2), 89–98.
Sadek, F., El-Tawil, S., and Lew, H. (2008). “Robustness of composite floor systems with shear connections: Modeling, simulation, and evaluation.” J. Struct. Eng., 1717–1725.
SDI (Steel Deck Institute). (2004). “Diaphragm design manual.”, Glenshaw, PA.
Tan, S., and Astaneh-Asl, A. (2003). “Cable-based retrofit of steel building floors to prevent progressive collapse.”, Dept. of Civil and Environmental Engineering, Univ. of California, Berkeley, CA.
Weigand, J. M., and Berman, J. W. (2014). “Integrity of steel single plate shear connections subjected to simulated column removal.” J. Struct. Eng., 04013114.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Dec 31, 2014
Accepted: May 7, 2015
Published online: Jun 25, 2015
Discussion open until: Nov 25, 2015
Published in print: Jan 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.