Torsional Behavior of Rectangular and Flanged Concrete Beams with FRP Reinforcements
Publication: Journal of Structural Engineering
Volume 141, Issue 12
Abstract
The demand for sustainable future infrastructures calls for new and innovative alternatives to avoid the problems associated with the conventional methods of construction. Fiber-reinforced polymer (FRP) bars have superior properties over conventional steel, mainly being noncorrosive. The objective of this study is to propose a model for predicting the full torsional behavior of concrete beams with the following: (1) carbon (C) or glass (G) FRP reinforcements, (2) different cross section shapes, and (3) adhesively bonded FRP stirrups or bent FRP stirrups. A brief recount of the findings from previous works is presented. Two previous models were adapted, and several new features were added to them, including but not limited to (1) recommending appropriate constitutive models for both the FRP and the concrete and (2) proposing failure criteria based on the experimentally observed failure modes. In addition, the first model was extended from an original strength model to a full behavior model (modified Collins). Moreover, the ability to analyze unsymmetrical beams with FRP reinforcements under torsion was added to the second model (modified Deifalla). The modified Deifalla model showed a slightly better agreement with the experimental results compared with the modified Collins model. In addition, modified Deifalla was capable of calculating the transversal strain at different faces of the cross section with a reasonable agreement compared to the experimentally observed ones. However, the modified Collins model was simpler than the modified Deifalla model. Further experimental data are needed before these findings can be generalized and refined.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support of the Science and Technology Development Fund (STDF) of Egypt, Short Term Fellowship Project ID 6482 is gratefully acknowledged.
References
ACI (American Concrete Institute). (2004). “Guide test methods for fiber reinforced polymers (FRP) for reinforcing or strengthening concrete structures.”, Farmington Hills, MI.
ACI (American Concrete Institute). (2006). “Guide for the design and construction of structural concrete reinforced with FRP bars.”, Farmington Hills, MI.
ACI (American Concrete Institute). (2013). “Report on torsion in structural concrete.”, Farmington Hills, MI.
Belarbi, A., and Hsu, T. (1995). “Constitutive laws of softened concrete in biaxial tension compression.” ACI Struct. J., 92(5), 562–573.
Bernardo, L., Andrade, J., and Lopes, S. (2012). “Modified variable angle truss-model for torsion in reinforced concrete beams.” Mater. Struct., 45(12), 1877–1902.
Canadian Standards Association. (2002). “Design and construction of building components with fiber-reinforced polymers.”, Toronto.
Chalioris, C. E. (2006). “Experimental study of the torsion of reinforced concrete members.” Struct. Eng. Mech., 23(6), 713–737.
Chalioris, C. E. (2008). “Torsional strengthening of rectangular and flanged beams using carbon fibre-reinforced-polymers—Experimental study.” Constr. Build. Mater., 22(1), 21–29.
Chalioris, C. E., and Karayannis, C. G. (2009). “Effectiveness of the use of steel fibres on the torsional behaviour of flanged concrete beams.” Cem. Concr. Compos., 31(5), 331–341.
Cocchi, G., and Volpi, M. (1996). “Inelastic analysis of reinforced concrete beams subjected to combined torsion, flexure and axial loads.” Comput. Struct., 61(3), 479–494.
Collins, M. P., and Mitchell, D. (1997). Prestressed concrete structures, Response Publication, Toronto.
Deifalla, A., and Ghobarah, A. (2010). “Full torsional behavior of RC beams wrapped with FRP: Analytical model.” Compos. Constr., 289–300.
Deifalla, A., and Ghobarah, A. (2014). “Behavior and analysis of inverted T-shaped RC beams under shear and torsion.” Eng. Struct., 68, 57–70.
Deifalla, A., Hamed, M., Saleh, A., and Ali, T. (2014a). “Exploring GFRP bars as reinforcement for rectangular and L-shaped beams subjected to significant torsion: An experimental study.” Eng. Struct., 59, 776–786.
Deifalla, A., Khali, M. S., and Abdelrahman, A. (2014b). “Simplified model for the torsional strength of concrete beams with GFRP stirrups.” Compos. Constr, 04014032.
Greene, G. J., and Belarbi, A. (2009). “Model for reinforced concrete members under torsion, bending, and shear. I: Theory.” J. Eng. Mech., 961–969.
Hsu, T. (1984). Torsion of reinforced concrete, Van Nostrand Reinhold Company, New York.
Hsu, T. (1993). Unified theory of reinforced concrete, CRC Press, Boca Raton, FL.
Japan Society of Civil Engineers. (1997). Recommendation for design and construction of concrete structures using continuous fiber reinforcing materials, Tokyo.
Jeng, C., and Hsu, T. (2009). “A softened membrane model for torsion in reinforced concrete members.” Eng. Struct., 31(9), 1944–1954.
Karayannis, C. G. (2000). “Smeared crack analysis for plain concrete in torsion.” J. Struct. Eng., 638–645.
Karayannis, C. G., and Chalioris, C. E. (2000). “Experimental validation of a smeared analysis for concrete in torsion.” J. Struct. Eng., 646–653.
Mitchell, D., and Collins, M. (1974). “Diagonal compression field theory—A rational model for structural concrete in pure torsion.” ACI Struct. J., 71, 396–408.
Mohamed, H., Chaallal, O., and Benmokrane, B. (2014). “Torsional moment capacity and failure mode mechanisms of concrete beams reinforced with carbon FRP bars and stirrups.” J. Compos. Constr., 04014049.
National Research Council. (2012). “Guide for the design and construction of externally bonded FRP systems for strengthening existing structures.”, Rome.
Onsongo, W. M. (1978). “Diagonal compression field theory for reinforced concrete beams subjected to combined torsion, flexure, and axial load.” Ph.D. thesis, Univ. of Toronto, Toronto.
Ragab, K. S., and Eisa, A. S. (2013). “Torsion; behavior of steel fibered high strength self compacting concrete beams reinforced by GFRB bars.” World Acad. Sci. Eng. Technol. Int. J. Civ. Archit. Sci. Eng., 7(9), 331–341.
Rahal, K. N., and Collins, M. P. (1995). “Analysis of sections subjected to combined shear and torsion—A theoretical model.” ACI Struct. J., 92(4), 459–469.
Shehab, H. K., El-Awady, M., Husain, M., and Mandour, S. (2009). “Behavior of concrete beams reinforced by GFRP bars under torsion.” Proc., 13th ICSGE. Cairo, Ain Shames Univ., Egypt.
Shirai, S., and Nougchi, H. (1989). “Compressive deterioration of cracked concrete.” Proc., ASCE Structures Congress, Design, Analysis and Testing, ASCE, New York, 1–10.
Vecchio, F., and Collins, M. (1982). The response of reinforced concrete to in-plane shear and normal stresses, Dept. of Civil Engineering, Univ. of Toronto, Toronto.
Vecchio, F., and Collins, M. (1986). “The modified compression field theory for concrete elements subjected to shear.” ACI Struct. J., 83(2), 219–231.
Walkenbach, J. (2010). Excel 2010 bible, Wiley, New York.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Feb 4, 2014
Accepted: Mar 12, 2015
Published online: May 18, 2015
Discussion open until: Oct 18, 2015
Published in print: Dec 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.