Mechanistic Model for Simulating Critical Behavior in Elastomeric Bearings
Publication: Journal of Structural Engineering
Volume 141, Issue 5
Abstract
When an elastomeric bearing is subjected to simultaneous vertical compressive load and lateral displacement, the shear force can pass through a maximum beyond which the bearing exhibits negative tangential horizontal stiffness and a condition of unstable equilibrium. This behavior has been experimentally demonstrated and has important implications on the stability and earthquake response of elastomeric seismic isolation bearings. Yet, analytical bearing models used for numerical earthquake simulation assume a positive second-slope stiffness irrespective of vertical load and/or bearing lateral displacement and therefore are unable to simulate the experimentally observed bearing behavior. Semiempirical bearing models have been developed and some of these models have been shown to simulate the influence of vertical load and lateral displacement on the shear force response with reasonable accuracy, however these models rely on a number of experimentally calibrated parameters, making them impractical for the purpose of design. An alternative approach to modeling the behavior of elastomeric bearings is explored in this study, which uses a series of vertical springs and a simple bilinear constitutive relationship to represent the rotational behavior of elastomeric bearings. The mechanistic bearing model, utilizing vertical springs, is shown to be capable of simulating the experimentally observed behavior with reasonable accuracy without relying on experimentally calibrated parameters.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the support of the National Science Foundation through award number CMMI-1031362. Furthermore, the authors would like to acknowledge the author of Sanchez et al. (2013) for providing experimental data through the NEES Project Warehouse (https://nees.org/warehouse/project/571) and award number CMMI-1113275. Any opinions, findings, and recommendations expressed in this paper are those of the authors and do not necessarily reflect the views of the funding institutions.
References
3D-Basis [Computer software]. Buffalo, NY, Univ. at Buffalo.
ABAQUS standard version 6.10 [Computer software]. DSSC, Providence, RI.
ASTM. “Standard test methods for vulcanized rubber and thermoplastic elastomers tension.” D412-06a, West Conshohocken, PA.
Buckle, I. G., and Liu, H. (1994). “Experimental determination of critical loads of elastomeric isolators at high shear strain.” NCEER Bull., 8(3), 1–5.
Buckle, I. G., Nagarajaiah, S., and Ferrell, K. (2002). “Stability of elastomeric isolation bearings: Experimental study.” J. Struct. Eng., 3–11.
Campolongo, F., and Braddock, B. (1999). “Sensitivity analysis of the IMAGE greenhouse model.” Environ. Modell. Software, 14(4), 275–282.
Constantinou, M. C., Kartoum, A., and Kelly, J. M. (1992). “Analysis of compression of hollow circular elastomeric bearings.” Eng. Struct., 14(2), 103–111.
Gent, A. N. (2001). Engineering with rubber: How to design rubber components, 2nd Ed., Hanser, Munich, Germany.
Han, X., Keller, C. A., Warn, G. P., and Wagener, T. (2013). “Identification of the controlling mechanism for predicting critical loads in elastomeric bearings.” J. Struct. Eng., 04013016.
Iizuka, M. (2000). “A macroscopic model for predicting large-deformation behaviors of laminated rubber bearings.” Eng. Struct., 22(4), 323–334.
Kelly, J. M. (1997). Earthquake resistant design with rubber, 2nd Ed., Springer, London.
Kelly, J. M., and Takhirov, S. M. (2004). “Analytical and numerical study on buckling of elastomeric bearings with various shape factors.”, Earthquake Engineering Research Center, Univ. of California, Berkeley, CA.
Kikuchi, M., Nakamura, T., and Aiken, I. D. (2010). “Three-dimensional analysis for square seismic isolation bearings under large shear deformations and high axial loads.” Earthquake Eng. Struct. Dyn., 39(13), 1513–1531.
Koh, C. G., and Kelly, J. M. (1988). “A simple mechanical model for elastomeric bearings used in base isolation.” Int. J. Mech. Sci., 30(12), 933–943.
Morris, M. D. (1991). “Factorial sampling plans for preliminary computational experiments.” Technometrics, 33(2), 161–174.
Mullins, L. (1969). “Softening of rubber by deformation.” Rubber Chem. Technol., 42(1), 339–362.
Nagarajaiah, S., and Ferrell, K. (1999). “Stability of elastomeric seismic isolation bearings.” J. Struct. Eng., 946–954.
Nagarajaiah, S., Reinhorn, A. M., and Constantinou, M. C. (1991). “Nonlinear dynamic analysis of 3D-base-isolated structures.” J. Struct. Eng., 2035–2054.
OpenSees V2.4.1 [Computer software]. Pacific Earthquake Engineering Research Center (PEER), Univ. of California, Berkeley, CA.
Sanchez, J., Masroor, A., Mosqueda, G., and Ryan, K. (2013). “Static and dynamic stability of elastomeric bearings for seismic protection of buildings.” J. Struct. Eng., 1149–1159.
SAP 2000 V15.2.1 [Computer software]. Computers and Structures (CSI), Walnut Creek, CA.
Warn, G. P., and Weisman, J. (2010). “Numerical study on the stability of elastomeric seismic isolation bearings.” 9th U.S. National and 10th Canadian Conf. on Earthquake Engineering, Earthquake Engineering Research Institute, Oakland, CA, 1008–1017.
Warn, G. P., and Weisman, J. (2011). “Parametric finite element investigation of the critical load capacity of elastomeric strip bearings.” Eng. Struct., 33(12), 3509–3515.
Warn, G. P., and Whittaker, A. S. (2006). “A study of the coupled horizontal-vertical behavior of elastomeric and lead-rubber seismic isolation bearings.”, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, NY.
Weisman, J., and Warn, G. P. (2012). “Stability of elastomeric and lead-rubber seismic isolation bearings.” J. Struct. Eng., 215–223.
Yamamoto, S., Kikuchi, M., Ueda, M., and Aiken, I. D. (2009). “A mechanical model for elastomeric seismic isolation bearings including the influence of axial load.” Earthquake Eng. Struct. Dyn., 38(2), 157–180.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Sep 26, 2013
Accepted: Mar 20, 2014
Published online: Jul 21, 2014
Discussion open until: Dec 21, 2014
Published in print: May 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.