Shear Behavior of High-Volume Fly Ash Concrete versus Conventional Concrete: Experimental Study
Publication: Journal of Structural Engineering
Volume 141, Issue 3
Abstract
The production of portland cement—the key ingredient in concrete—generates a significant amount of carbon dioxide. However, due to its incredible versatility, availability, and relatively low cost, concrete is the most consumed synthetic material on the planet. One method of reducing concrete’s contribution to greenhouse-gas emissions is the use of fly ash to replace a significant amount of the cement. This paper compares two experimental studies that were conducted to investigate the shear strength of full-scale beams constructed with both high-volume fly ash concrete (HVFAC)—concrete with at least 50% of the cement replaced with fly ash—and conventional concrete (CC). The primary difference between the two studies involved the amount of cementitious material, with one mix having a relatively high-total cementitious content [ ()] and the other mix having a relatively low-total cementitious content [ ()]. Both HVFAC mixes used a 70% mass replacement of portland cement with Class C fly ash. Each of these experimental programs consisted of 16 beams—eight constructed from HVFAC and eight constructed from CC—with three different longitudinal reinforcement ratios. The beams were tested under a simply supported four-point-loading condition. The experimental shear strengths of the beams were compared with both the shear provisions of selected standards (United States, Australia, Canada, Europe, and Japan) and a shear database of CC specimens. This comparison indicates that the HVFAC beams possess superior shear strength compared with the CC beams.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support provided by the MoDOT and the National University Transportation Center at Missouri University of Science and Technology. The conclusions and opinions expressed in this paper are those of the authors and do not necessarily reflect the official views or policies of the funding institutions.
References
AASHTO. (2010). AASHTO LRFD bridge design specifications, 4th Ed., Washington, DC, 72–84.
ACI Committee 211. (1993). “Guide for selecting proportions for high-strength concrete with portland cement and fly ash.” ACI Mater. J., 90(3), 272–283.
ACI Committee 232. (2003). “Use of fly ash in concrete.”, Farmington Hills, MI.
American Concrete Institute ACI Committee. (2011). “Building code requirements for structural concrete ACI 318-08and commentary 318R-08.”, Farmington Hills, MI, 155–168.
ASTM. (2010a). “Standard test method for density (unit weight), yield, and air content (gravimetric) of concrete.” C138/C138M-10a, West Conshohocken, PA, 4.
ASTM. (2010b). “Standard test method for flexural strength of concrete using simple beam with third-point loading.” C78/C78M-10, West Conshohocken, PA, 4.
ASTM. (2010c). “Standard test method for slump of hydraulic-cement concrete.” C143/C143M-10a, West Conshohocken, PA, 4.
ASTM. (2011). “Standard test method for splitting tensile strength of cylindrical concrete.” C496/C496M-11, West Conshohocken, PA, 5.
ASTM. (2012a). “Standard test method for air content of freshly mixed concrete by the volumetric method1.” C173/C173M-12, West Conshohocken, PA, 9.
ASTM. (2012b). “Standard specification for deformed and plain carbon-steel bars for concrete reinforcement.” A615/A615-12, West Conshohocken, PA, 6.
ASTM. (2012c). “Standard test method for compressive strength of cylindrical concrete specimens.” C39/C39M-12, West Conshohocken, PA, 7.
ASTM. (2012d). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” C618, West Conshohocken, PA, 3.
Bazant, Z. P., and Becq-Giraudon, E. (2002). “Statistical prediction of fracture parameters of concrete and implications for choice of testing standards.” Cem. Concr. Res. J., 32(4), 529–556.
Bažant, Z. P., and Yu, Q. (2005). “Design against size effect on shear strength of reinforced concrete beams without stirrups.” J. Struct. Eng., 1877–1885.
Bentz, D. P. (2010). “Powder additions to mitigate retardation in high-volume fly ash mixtures.” ACI Mater. J., 107(5), 508–514.
Berry, E. E., Hemmings, R. T., Zhang, M. H., Cornelious, B. J., and Golden, D. M. (1994). “Hydration in high-volume fly ash binders.” ACI Mater. J., 91(4), 382–389.
Bilodeau, A., and Malhotra, V. M. (2000). “High-volume fly ash system: Concrete solution for sustainable development.” ACI Mater. J., 97(1), 41–48.
Canadian Standards Association. (2004). “Design of concrete standards for buildings.”, Rexdale, Ontario, Canada, 53–61.
Cross, D., Stephens, J., and Vollmer, J. (2005). “Structural applications of 100 percent fly ash concrete.” Proc., 2005 World of Coal Ash (WOCA), 1–19.
Davis, R. E., Carlson, R. W., Kelly, J. W., and Davis, H. E. (1937). “Properties of cements and concretes containing fly ash.” J. Am. Concr. Inst., 33(5), 577–612.
Dunstan, E. R. (1976). “Performance of lignite and sub-bituminous fly ash in concrete.”, U.S. Bureau of Reclamation, Denver, 23.
Dunstan, E. R. (1980). “A possible method for identifying fly ashes that will improve the sulfate resistance of concretes.” Cem. Concr. Aggregates, 2(1), 20–30.
Dunstan, E. R. (1984). “Fly ash and fly ash concrete.”, Bureau of Reclamation, Denver, 42.
European Committee for Standardization. (2005). “Design of concrete structures. Part 1: General rules and rules for buildings.” Eurocode 2, Brussels, 84–92.
Gastebled, O. J., and May, I. M. (2001). “Fracture mechanics model applied to shear failure of reinforced concrete beams without stirrups.” ACI Struct. J., 98(2), 184–190.
Gopalan, M. K. (1993). “Nucleation and pozzolanic factors in strength development of class F fly ash concrete.” ACI Mater. J., 90(2), 117–121.
Hanle, L., Jayaraman, K., and Smith, J. (2012). “ emissions profile of the U.S. cement industry.” 〈http://infohouse.p2ric.org/ref/43/42552.pdf〉 (Dec. 26, 2013).
Japan Society of Civil Engineers. (2007). “Standard specification for concrete structure.” JSCE No. 15, Tokyo, 154–159.
Koyama, T., Sun, Y. P., Fujinaga, T., Koyamada, H., and Ogata, F. (2008). “Mechanical properties of concrete beam made of a large amount of fine fly ash.” Proc. for the 14th World Conf. on Earthquake Engineering, Mira Digital Publishing, St. Louis, MO.
Malhotra, V. M. (1986). “Superplasticized fly ash concrete for structural applications.” Concr. Int., 8(12), 28–31.
Marland, G., Boden, T. A., and Andres, R. J. (2008). “Global, regional, and national fossil fuel emissions.” Trends: A compendium of data on global change, Carbon Dioxide Information Analysis Center, Oak Ridge National Laboratory, United States Dept. of Energy, Oak Ridge, TN.
Minitab 15 [Computer software]. Statistical Software, Minitab.
Myers, J. J., and Carrasquillo, R. L. (1999). “Mix proportioning for high-strength HPC bridge beams.” American Concrete Institute Special Publication 189, American Concrete Institute, Detroit, MI, 37–56.
Rao, R. M., Mohan, S., and Sekar, S. K. (2011). “Shear resistance of high volume fly ash reinforced concrete beams without web reinforcement.” Int. J. Civ. Struct. Eng., 1(4), 986–993.
Reineck, K. H., Kuchma, D. A., Kim, K. S., and Marx, S. (2003). “Shear database for reinforced concrete members without shear reinforcement.” ACI Struct. J., 100(2), 240–249.
RILEM. (1985). “Determination of the fracture energy of mortar and concrete by means of three-point bend tests on notched beams.” RILEM Recommendation Mater. Struct., 18(4), 287–290.
Standards Australia. (2009). “Concrete structures.” AS-3600, Sydney, Australia, 105–109.
Taylor, H. P. J. (1972). “Shear strength of large beams.” J. Struct. Div., 98(ST11), 2473–2489.
Taylor, H. P. J. (1974). “The fundamental behavior of reinforced concrete beams in bending and shear.” Shear in Reinforced Concrete, SP-42, American Concrete Institute, Farmington Hills, MI, 43–77.
U.S. Geological Survey. (2012). Minerals yearbook, cement, United States Dept. of the Interior, Reston, VA, 38–39.
Xu, S., Zhang, X., and Reinhardt, H. W. (2012). “Shear capacity prediction of reinforced concrete beams without stirrups using fracture mechanics approach.” ACI Struct. J., 109(5), 705–714.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Aug 9, 2012
Accepted: Nov 13, 2013
Published online: Apr 9, 2014
Discussion open until: Sep 9, 2014
Published in print: Mar 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.