Experimental Investigation of SPSW Web Plate Stress Field Development and Vertical Boundary Element Demand
Publication: Journal of Structural Engineering
Volume 140, Issue 6
Abstract
Steel plate shear walls (SPSW) are an efficient but largely underutilized building lateral force resisting system. The system consists of a moment frame (the boundary frame) with slender steel web plates that are welded or bolted inside the boundary frame, forming a diaphragm. The resulting structure resembles a vertical plate girder. The system resists lateral load primarily through tension field action of the postbuckled web plate. The magnitude and orientation of this tension field is governed by the relative stiffness of the web plate and boundary frame. The 2010 Seismic Provisions currently require that the tension field inclination angle be either 40° or computed using a closed-form equation derived from elastic analysis. It is demonstrated through experimentation and finite-element analyses that the tension field inclination may migrate, from an initially low angle under an elastic postbuckled state, toward 45° as the plate is loaded plastically. The resulting flexural demand on the vertical boundary elements is consistent with this change for both monotonic and cyclic loading. Through a series of small-scale experiments, slender A1008 steel web plates were loaded inside a square reusable pin-connected frame. The aim of this study was to examine the interaction of the web plate with the boundary frame members and the development and change in the web plate tension field orientation. This paper presents the results of the experiments and some of the numerical simulations that were used to study the migration of the tension field orientation angle, and extend the results to a variety of SPSW configurations.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was carried out as part of the NEES SPSW project for “NEESR-SG: Smart and Resilient Steel Walls for Reducing Earthquake Impacts.” Financial support for this study was provided by the National Science Foundation as part of the George E. Brown Network for Earthquake Engineering Simulation under award number CMMI-0830294.
References
ABAQUS 6.9 [Computer software]. Dassault Systèmes Simulia, Providence, RI.
American Institute of Steel Construction. (2005). Seismic Provisions for Structural Steel Buildings, Chicago.
American Institute of Steel Construction. (2010). Specification for Structural Steel Buildings, Chicago.
Behbahanifard, M. R. (2003). “Cyclic behavior of unstiffened steel plate shear walls.” Doctoral dissertation, Univ. of Alberta, Edmonton, Alberta.
Chen, R. (1991). “Cyclic behavior of unstiffened thin steel plate shear walls.” Doctoral dissertation, Univ. of Maine, Orono, ME.
Computers and Structures (CSI). (2009). SAP2000 v.12.0.2 user manual, Berkeley, CA.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behavior of steel plate shear walls.”, Univ. of Alberta, Edmonton, Alberta.
Elgaaly, M., Caccese, V., and Du, R. (1993). “Post-buckling behavior of steel plate shear walls under cyclic loads.” J. Struct. Eng., 588–605.
Jalali, A., and Sazgari, A. (2006). “Experimental and theoretical post-buckling study of steel shear walls.” Proc., of the NSC/NARL 4th Int. Conf. on Earthquake Engineering, 114.
Kharrazi, M. H. K. (2005). “Rational method for analysis and design of steel plate walls.” Doctoral dissertation, Univ. of British Columbia, Vancouver, BC.
Lubell, A. S. (1997). “Performance of unstiffened steel plate shear walls under cyclic quasi-static loading.” Master’s thesis, Univ. of British Columbia, Vancouver, BC.
Rezai, M. (1999). “Seismic behavior of steel plate shear walls by shake table testing.” Doctoral dissertation, Univ. of British Columbia, Vancouver, BC.
Roberts, T. M., and Sabouri-Ghomi, S. (1991). “Hysteretic characteristics of unstiffened plate shear panels.” Thin-Walled Struct., 12(2), 145–162.
Somerville, P., Smith, N., Punyamurthula, S., and Sun, J. (1997). “Development of ground motion time histories for phase 2 of the FEMA/SAC steel project. SAC background document.”, SAC Joint Venture, Richmond, CA.
Thornburn, L. J., Kulak, G. L., and Montgomery, C. J. (1983). “Analysis of steel plate shear walls.”, Univ. of Alberta, Edmonton, Alberta.
Timler, P. A., and Kulak, G. L. (1983). “Experimental study of steel plate shear walls.”, Univ. of Alberta, Edmonton, Alberta.
Tromposch, E. W., and Kulak, G. L. (1987). “Cyclic and static behavior of thin panel steel plate shear walls.”, Univ. of Alberta, Edmonton, Alberta.
Webster, D. J. (2013). “The inelastic seismic response of a steel plate shear wall web plate and its interaction with the vertical boundary frame members.” Doctoral Dissertation, Univ. of Washington, Seattle, WA.
Webster, D. J., Berman, J. W., and Lowes, L. N. (2012). “The elastic and inelastic post-buckling behavior of steel plate shear wall web plates and their interaction with vertical boundary elements.” Proc., Annual SSRC Stability Conf., Chicago, IL.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 140 • Issue 6 • June 2014
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Apr 17, 2013
Accepted: Oct 28, 2013
Published online: Feb 17, 2014
Published in print: Jun 1, 2014
Discussion open until: Jul 17, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.